Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Journal of Applied Physics

Testing the effect of surface coatings on alkali atom polarization lifetimes

Scott J. Seltzer, David M. Rampulla, Sandrine Rivillon, Yves Jean Chabal, Steven L. Bernasek, Michael V. Romalis

Published Nov 15, 2008• 62 citations
Publisher

Abstract

The evaluation of different surface coatings used in alkali metal atomic magnetometers is necessary for the improvement of sensitivity of these devices. A method to measure the polarization lifetime of alkali atoms in the region between substrates with different coatings was developed to determine the effectiveness of the coating at preserving alkali spin polarization as well as chemical compatibility and high-temperature stability. Multiple coatings can be compared under identical experimental conditions, using an experimental geometry that allows surface characterization before and after evaluation of the polarization lifetime. Multilayered, cross-linked octadecyltrichlorosilane films, alkyltrichlorosilane monolayers, and octadecylphosphonic acid monolayers were evaluated using this approach.

DOI
10.1063/1.2985913

Related papers

An evaluation method for anti-relaxation coatings in alkali-metal vapor cells based on cumulative relaxation damage factor

Haoran Xu, Yi-an Xu, Yuan Hu +3 more

Abstract Alkali‑metal vapor cells are critical for quantum precision measurement devices such as atomic gyroscopes, magnetometers and clocks. The anti‑relaxation coating on cell walls determines atomic spin polarization lifetime and measurement sensitivity. Conventional evaluations depend on short‑term relaxation tests and fail to characterize long‑term coating stability and microscopic degradation. This work proposes a novel evaluation method based on a cumulative relaxation damage factor. From long‑range kinetic perspectives, alkali‑metal surface dynamics are decomposed into three elementary processes quantified by adsorption energy, charge transfer and diffusion barrier. Drawing on Lusser’s reliability law, we construct this unified factor to interpret relaxation mechanisms and assess coating performance. A first‑principles computational framework with periodic slab models is established for alkali‑metal and organic/inorganic interfaces, validated using experimental interaction parameters of four typical coatings. The simulation results demonstrate that the proposed cumulative relaxation damage factor effectively distinguishes the anti-relaxation performance of different coatings and exhibits general applicability across various alkali-metal species. This study converts cumulative long‑range kinetic relaxation into microscopic coating design rules, offering a theoretical tool for wall‑collision relaxation analysis, coating screening and quantum sensing instruments optimization.

•Sep 23, 2026•0 citations

Investigation of antirelaxation coatings for alkali-metal vapor cells using surface science techniques

Scott J. Seltzer, David J. Michalak, Marcus H. Donaldson +17 more

Many technologies based on cells containing alkali-metal atomic vapor benefit from the use of antirelaxation surface coatings in order to preserve atomic spin polarization. In particular, paraffin has been used for this purpose for several decades and has been demonstrated to allow an atom to experience up to 10 000 collisions with the walls of its container without depolarizing, but the details of its operation remain poorly understood. We apply modern surface and bulk techniques to the study of paraffin coatings in order to characterize the properties that enable the effective preservation of alkali spin polarization. These methods include Fourier transform infrared spectroscopy, differential scanning calorimetry, atomic force microscopy, near-edge x-ray absorption fine structure spectroscopy, and x-ray photoelectron spectroscopy. We also compare the light-induced atomic desorption yields of several different paraffin materials. Experimental results include the determination that crystallinity of the coating material is unnecessary, and the detection of C[Double Bond]C double bonds present within a particular class of effective paraffin coatings. Further study should lead to the development of more robust paraffin antirelaxation coatings, as well as the design and synthesis of new classes of coating materials.

arXiv:1002.4417•The Journal of Chemical Physics•Oct 11, 2010•69 citations

High-temperature alkali vapor cells with antirelaxation surface coatings

Scott J. Seltzer, Michael V. Romalis

Antirelaxation surface coatings allow long spin relaxation times in alkali-metal cells without buffer gas, enabling faster diffusion of the alkali atoms throughout the cell and giving larger signals due to narrower optical linewidths. Effective coatings were previously unavailable for operation at temperatures above 80 °C. We demonstrate that octadecyltrichlorosilane (OTS) can allow potassium or rubidium atoms to experience hundreds of collisions with the cell surface before depolarizing, and that an OTS coating remains effective up to about 170 °C for both potassium and rubidium. We consider the experimental concerns of operating without buffer gas and with minimal quenching gas at high vapor density, studying the stricter need for effective quenching of excited atoms and deriving the optical rotation signal shape for atoms with resolved hyperfine structure in the spin-temperature regime. As an example of a high-temperature application of antirelaxation coated alkali vapor cells, we operate a spin-exchange relaxation-free atomic magnetometer with sensitivity of 6 fT/Hz and magnetic linewidth as narrow as 2 Hz.

arXiv:0906.3054•Journal of Applied Physics•Dec 1, 2009•146 citations

Anti-relaxation coating of the vapor cell

Xie Xin, Liu Yunhui, Bai Yuanyuan +1 more

In order to achieve the maximum possible polarization lifetime of the alkali atoms in the vapor cell, we discussed several spin-relaxation mechanisms and anti-relaxation methods. We found that octadecyltrichlorosilane (OTS) acts as an anti-relaxation coating for alkali atoms, with good effect in high-temperature conditions.

International Conference on Optoelectronics and Microelectronics•Sep 1, 2013•0 citations

Effects of organic film morphology on the formation of Rb clusters on surface coatings in alkali metal vapor cells

David M. Rampulla, Nuri Oncel, Esta Abelev +3 more

Surface relaxation rates differ for spin-polarized alkali atoms interacting with monolayer or bilayer octadecyltrichlorosilane (OTS) coatings. The morphology and composition of Rb vapor-exposed films of OTS have been studied with atomic force microscopy (AFM) and x-ray photoelectron spectroscopy (XPS). On OTS monolayers, numerous small (<500 nm wide) Rb containing islands nucleate at the boundaries of the ∼1–2 μm wide organic domains. On OTS bilayers, singular large (∼3 μm wide) Rb containing islands were found. Alkali island formation mediated by surface structure could affect the antirelaxation behavior of organic coatings used in atomic magnetometer cells.

Applied Physics Letters•Jan 26, 2009•25 citations

Method for characterizing self-assembled monolayers as antirelaxation wall coatings for alkali vapor cells

Youngwoo Yi, H. G. Robinson, Svenja A. Knappe +5 more

We describe a method for characterizing self-assembled monolayers (SAMs) in terms of their performance as antirelaxation wall coatings for alkali atom vapor cells. A combination of initial surface analysis and subsequent laser spectroscopy is used to provide insight into the quality of the coating, as well as its performance under the exposure to alkalis as it occurs, for example, when used in applications such as atomic magnetometers or clocks. Fused silica plates coated with octadecyltrichlorosilane SAMs were used to make cubic R87b gas cells. The surface was characterized by x-ray diffraction, contact angle measurements, and atomic force microscopy. Measurements of hyperfine resonance linewidths and frequency shifts show that the rubidium vapor atoms collide up to 40 times with the walls of the cells before their coherence relaxes and their adsorption energy is around 0.065 eV. Chemical analysis of the cell indicates some weak reactions between the coating and the rubidium atoms.

Journal of Applied Physics•Jul 15, 2008•77 citations
The evaluation of different surface coatings used in alkali metal atomic magnetometers is necessary for the improvement of sensitivity of these devices. A method to measure the polarization lifetime of alkali atoms in the region between substrates with different coatings was developed to determine the effectiveness of the coating at preserving alkali spin polarization as well as chemical compatibility and high-temperature stability. Multiple coatings can be compared under identical experimental conditions, using an experimental geometry that allows surface characterization before and after evaluation of the polarization lifetime. Multilayered, cross-linked octadecyltrichlorosilane films, alkyltrichlorosilane monolayers, and octadecylphosphonic acid monolayers were evaluated using this approach.
Abstract Alkali‑metal vapor cells are critical for quantum precision measurement devices such as atomic gyroscopes, magnetometers and clocks. The anti‑relaxation coating on cell walls determines atomic spin polarization lifetime and measurement sensitivity. Conventional evaluations depend on short‑term relaxation tests and fail to characterize long‑term coating stability and microscopic degradation. This work proposes a novel evaluation method based on a cumulative relaxation damage factor. From long‑range kinetic perspectives, alkali‑metal surface dynamics are decomposed into three elementary processes quantified by adsorption energy, charge transfer and diffusion barrier. Drawing on Lusser’s reliability law, we construct this unified factor to interpret relaxation mechanisms and assess coating performance. A first‑principles computational framework with periodic slab models is established for alkali‑metal and organic/inorganic interfaces, validated using experimental interaction parameters of four typical coatings. The simulation results demonstrate that the proposed cumulative relaxation damage factor effectively distinguishes the anti-relaxation performance of different coatings and exhibits general applicability across various alkali-metal species. This study converts cumulative long‑range kinetic relaxation into microscopic coating design rules, offering a theoretical tool for wall‑collision relaxation analysis, coating screening and quantum sensing instruments optimization.
Many technologies based on cells containing alkali-metal atomic vapor benefit from the use of antirelaxation surface coatings in order to preserve atomic spin polarization. In particular, paraffin has been used for this purpose for several decades and has been demonstrated to allow an atom to experience up to 10 000 collisions with the walls of its container without depolarizing, but the details of its operation remain poorly understood. We apply modern surface and bulk techniques to the study of paraffin coatings in order to characterize the properties that enable the effective preservation of alkali spin polarization. These methods include Fourier transform infrared spectroscopy, differential scanning calorimetry, atomic force microscopy, near-edge x-ray absorption fine structure spectroscopy, and x-ray photoelectron spectroscopy. We also compare the light-induced atomic desorption yields of several different paraffin materials. Experimental results include the determination that crystallinity of the coating material is unnecessary, and the detection of C[Double Bond]C double bonds present within a particular class of effective paraffin coatings. Further study should lead to the development of more robust paraffin antirelaxation coatings, as well as the design and synthesis of new classes of coating materials.
Antirelaxation surface coatings allow long spin relaxation times in alkali-metal cells without buffer gas, enabling faster diffusion of the alkali atoms throughout the cell and giving larger signals due to narrower optical linewidths. Effective coatings were previously unavailable for operation at temperatures above 80 °C. We demonstrate that octadecyltrichlorosilane (OTS) can allow potassium or rubidium atoms to experience hundreds of collisions with the cell surface before depolarizing, and that an OTS coating remains effective up to about 170 °C for both potassium and rubidium. We consider the experimental concerns of operating without buffer gas and with minimal quenching gas at high vapor density, studying the stricter need for effective quenching of excited atoms and deriving the optical rotation signal shape for atoms with resolved hyperfine structure in the spin-temperature regime. As an example of a high-temperature application of antirelaxation coated alkali vapor cells, we operate a spin-exchange relaxation-free atomic magnetometer with sensitivity of 6 fT/Hz and magnetic linewidth as narrow as 2 Hz.
Surface relaxation rates differ for spin-polarized alkali atoms interacting with monolayer or bilayer octadecyltrichlorosilane (OTS) coatings. The morphology and composition of Rb vapor-exposed films of OTS have been studied with atomic force microscopy (AFM) and x-ray photoelectron spectroscopy (XPS). On OTS monolayers, numerous small (<500 nm wide) Rb containing islands nucleate at the boundaries of the ∼1–2 μm wide organic domains. On OTS bilayers, singular large (∼3 μm wide) Rb containing islands were found. Alkali island formation mediated by surface structure could affect the antirelaxation behavior of organic coatings used in atomic magnetometer cells.
We describe a method for characterizing self-assembled monolayers (SAMs) in terms of their performance as antirelaxation wall coatings for alkali atom vapor cells. A combination of initial surface analysis and subsequent laser spectroscopy is used to provide insight into the quality of the coating, as well as its performance under the exposure to alkalis as it occurs, for example, when used in applications such as atomic magnetometers or clocks. Fused silica plates coated with octadecyltrichlorosilane SAMs were used to make cubic R87b gas cells. The surface was characterized by x-ray diffraction, contact angle measurements, and atomic force microscopy. Measurements of hyperfine resonance linewidths and frequency shifts show that the rubidium vapor atoms collide up to 40 times with the walls of the cells before their coherence relaxes and their adsorption energy is around 0.065 eV. Chemical analysis of the cell indicates some weak reactions between the coating and the rubidium atoms.