Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Applied Physics Letters

Ion implantation into Nb/Nb oxide/PbAuIn Josephson tunnel junctions

Stanley I. Raider, G. J. Clark

Published Oct 1, 1984• 2 citations
Publisher

Abstract

Boron ions have been implanted into complete planar and edge Nb/Nb oxide/PbAuIn Josephson tunnel junctions to directly trim the Josephson current I0. Implantation caused reproducible increases in I0 and in the junction subgap conductance and decreases in the junction energy gap voltage Vg. The variations in junction properties were monotonic with 11B implant dose. Trimming of I0 was optimized when the 11B ions were implanted with the depth distribution peaked near the tunnel barrier.

DOI
10.1063/1.95369

Related papers

Nb/Nb oxide/Pb-alloy Josephson tunnel junctions

Stanley I. Raider, R.E. Drake

A procedure is described for fabricating thin film Nb/Nb oxide/Pb-alloy Josephson tunnel junctions that satisfies the principal requirements for integrated circuit design and fabrication. A deposited Nb film, evaporated from an e-gun heated source, was patterned by chemical etching to form a base electrode. A junction was completed by plasma etching and plasma oxidizing the Nb junction area to form a tunnel barrier and by depositing a Pb alloy counterelectrode. Josephson tunnel junctions with Nb/Nb oxide/Pb-Au-In structures were prepared with low excess subgap currents in the current-voltage (I-V) curve and with reproducible and stable I-V characteristics. Variations in junction current density from run-run were ± 15%. Seven 3-junction interferomeeters out of a population of 50,000 were shorted (99.99% yield) for causes not immediately attributable to photoresist-related defects. No changes in Josephson current were detected after thermal cycling 17,000 interferometers 1,800 × between room temperature and 4.2°K, after storing them for 2 years at 5°C, or after annealing 5,000 interferometers for 4.5 hours at 70°C.

IEEE Transactions on Magnetics•Jan 1, 1981•41 citations

Fabrication of ultrasmall Nb-AlOx-Nb Josephson tunnel junctions

John M. Martinis, Ronald H. Ono

We describe a fabrication process to make Nb-AlOx-Nb edge junctions with areas as small as 0.0022 μm2 and with current densities from 10 to 24 000 A/cm2. The junction conductance was low for voltages below the superconducting energy gap which indicates good quality tunnel barriers. Coulomb gap measurements obtained when the junctions were in the normal state were used to find the junction capacitance. Junction capacitance as small as 0.18 fF has been measured.

Applied Physics Letters•Aug 6, 1990•34 citations

Niobium nitride Josephson tunnel junctions with magnesium oxide barriers

Akira Shoji, Masahiro Aoyagi, S. Kosaka +2 more

Niobium nitride-niobium nitride Josephson tunnel junctions have been fabricated using amorphous magnesium oxide (a-MgO) films as barriers. These junctions have excellent tunneling characteristics. For example, a large gap voltage (Vg=5.1 mV), a large product of the maximum critical current and the normal tunneling resistance (IcRn=3.25 mV), and a small subgap leakage current (Vm=45 mV, measured at 3 mV) have been obtained for a NbN/a-MgO/NbN junction. The critical current of this junction remains finite up to 14.5 K.

Applied Physics Letters•Jun 1, 1985•138 citations

Tunneling properties of single crystal Nb/Nb2O5/Pb Josephson junctions

Sergio Celaschi, T. H. Geballe, Walter P. Lowe

Preparation of high quality single crystal Nb tunnel junctions based on Nb/Nb2O5/Pb structures is reported. Vm values of 30±10 mV were obtained. The average specific capacitance of these junctions is 0.020±0.002 pF/μm2. From measurements of the oxidation rate, the conductance at high voltage bias, and observations of the tunneling behavior, we show that some characteristics previously associated with oxidized niobium barriers are not intrinsic and are significantly improved when the underlying niobium film is single crystal.

Applied Physics Letters•Oct 15, 1983•24 citations

Postfabrication resistance trimming of a superconducting tunnel junction using a focused ion beam

Z. H. Barber, Mark G. Blamire, Nick Dawes

A high current density NbN/MgO/Nb superconducting tunnel junction has been modified using a focused ion beam to trim the junction area following fabrication and measurement. After milling, the exposed edge of the junction was cleaned of resputtered material using a low current ion beam combined with gas assisted etching. Some remaining shorts across the barrier were then removed by anodization. The modified junction showed a resistance increase correlating exactly with the decrease in area and very little change in quality. This technique may be used on fully fabricated circuits to trim accurately the resistance of selected junctions in order to overcome variations in barrier conductance and junction area.

Journal of Vacuum Science & Technology B Microelectronics and Nanometer Structures Processing Measurement and Phenomena•Mar 1, 1995•2 citations

Fabrication of all-NbN Josephson tunnel junctions using single crystal NbN films for the base electrodes

Alexandre Shoji

All-NbN Josephson tunnel junctions with sputter-deposited magnesium oxide barriers have been fabricated using single-crystal NbN films for the base electrodes. Fabricated Josephson junctions have shown good tunneling characteristics with large gap voltages (5.6-5.8 mV), narrow gap widths (0.1-0.2 mV, from 30 to 70%), and small subgap leakage currents (V/sub m/=20-30 mV, measured at 3 mV). The results of a measurement of a subgap structure for a fabricated junction suggest that the excess leakage currents of fabricated junctions are due to multiparticle tunneling through locally thin areas in the MgO barriers.

IEEE Transactions on Magnetics•Mar 1, 1991•25 citations
Boron ions have been implanted into complete planar and edge Nb/Nb oxide/PbAuIn Josephson tunnel junctions to directly trim the Josephson current I0. Implantation caused reproducible increases in I0 and in the junction subgap conductance and decreases in the junction energy gap voltage Vg. The variations in junction properties were monotonic with 11B implant dose. Trimming of I0 was optimized when the 11B ions were implanted with the depth distribution peaked near the tunnel barrier.
A procedure is described for fabricating thin film Nb/Nb oxide/Pb-alloy Josephson tunnel junctions that satisfies the principal requirements for integrated circuit design and fabrication. A deposited Nb film, evaporated from an e-gun heated source, was patterned by chemical etching to form a base electrode. A junction was completed by plasma etching and plasma oxidizing the Nb junction area to form a tunnel barrier and by depositing a Pb alloy counterelectrode. Josephson tunnel junctions with Nb/Nb oxide/Pb-Au-In structures were prepared with low excess subgap currents in the current-voltage (I-V) curve and with reproducible and stable I-V characteristics. Variations in junction current density from run-run were ± 15%. Seven 3-junction interferomeeters out of a population of 50,000 were shorted (99.99% yield) for causes not immediately attributable to photoresist-related defects. No changes in Josephson current were detected after thermal cycling 17,000 interferometers 1,800 × between room temperature and 4.2°K, after storing them for 2 years at 5°C, or after annealing 5,000 interferometers for 4.5 hours at 70°C.
Niobium nitride-niobium nitride Josephson tunnel junctions have been fabricated using amorphous magnesium oxide (a-MgO) films as barriers. These junctions have excellent tunneling characteristics. For example, a large gap voltage (Vg=5.1 mV), a large product of the maximum critical current and the normal tunneling resistance (IcRn=3.25 mV), and a small subgap leakage current (Vm=45 mV, measured at 3 mV) have been obtained for a NbN/a-MgO/NbN junction. The critical current of this junction remains finite up to 14.5 K.
Preparation of high quality single crystal Nb tunnel junctions based on Nb/Nb2O5/Pb structures is reported. Vm values of 30±10 mV were obtained. The average specific capacitance of these junctions is 0.020±0.002 pF/μm2. From measurements of the oxidation rate, the conductance at high voltage bias, and observations of the tunneling behavior, we show that some characteristics previously associated with oxidized niobium barriers are not intrinsic and are significantly improved when the underlying niobium film is single crystal.
A high current density NbN/MgO/Nb superconducting tunnel junction has been modified using a focused ion beam to trim the junction area following fabrication and measurement. After milling, the exposed edge of the junction was cleaned of resputtered material using a low current ion beam combined with gas assisted etching. Some remaining shorts across the barrier were then removed by anodization. The modified junction showed a resistance increase correlating exactly with the decrease in area and very little change in quality. This technique may be used on fully fabricated circuits to trim accurately the resistance of selected junctions in order to overcome variations in barrier conductance and junction area.
All-NbN Josephson tunnel junctions with sputter-deposited magnesium oxide barriers have been fabricated using single-crystal NbN films for the base electrodes. Fabricated Josephson junctions have shown good tunneling characteristics with large gap voltages (5.6-5.8 mV), narrow gap widths (0.1-0.2 mV, from 30 to 70%), and small subgap leakage currents (V/sub m/=20-30 mV, measured at 3 mV). The results of a measurement of a subgap structure for a fabricated junction suggest that the excess leakage currents of fabricated junctions are due to multiparticle tunneling through locally thin areas in the MgO barriers.