Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Journal of Modern Optics

Maximum count rate of large area superconducting single photon detectors

Mikkel Ejrnaes, A. Casaburi, Roberto Cristiano, Orlando Quaranta, S. Marchetti, S. Pagano

Published Jan 20, 2009• 23 citations
Publisher

Abstract

An analysis of different strategies for increasing the maximum count rate of superconducting single photon detectors using parallel nanowires is performed with particular emphasis on the expected behaviour when the detector area is increased. We find that for a serial connection of blocks of parallel nanowires, the maximum count rate decreases with the square root of the detector area, whereas it decreases proportional to the detector area for current meandered detectors. Using this design we estimate that a signal pulse falltime of 7.8 ns for a 84 × 84 µm2 parallel detector based on current material parameters should be obtainable. We argue that the slow decrease of count rate with detector area might permit detectors based on parallel nanowires to fully exploit the available cooling power.

DOI
10.1080/09500340802673182

Related papers

Characterization of parallel superconducting nanowire single photon detectors

Mikkel Ejrnaes, A. Casaburi, Orlando Quaranta +6 more

Superconducting nanowire single photon detectors (SNSPDs) have been realized using an innovative parallel wire configuration. This configuration allows, at the same time, a large detection area and a fast response, with the additional advantage of large signal amplitudes. The detectors have been thoroughly characterized in terms of signal properties (amplitude, risetime and falltime), detector operation (latching and not latching) and quantum efficiency (at 850 nm). It has been shown that the parallel SNSPD is able to provide significantly higher maximum count rates for large area SNSPDs than meandered SNSPDs. Through a proper parallel wire configuration the increase in maximum count rate can be obtained without latching problems.

Superconductor Science and Technology•Mar 30, 2009•55 citations

Large area single photon detectors based on parallel configuration NbN nanowires

F. Mattioli, Mikkel Ejrnaes, Alessandro Gaggero +4 more

The authors present superconducting single photon detectors (SSPDs) based on parallel nanostrips with an area up to 40 × 40 μm2. The SSPDs presented here are based on 100 nm wide ultrathin NbN nanostrips with a filling factor of 40%. The devices are fabricated by extending the standard electron beam lithography (EBL) patterning process to those densely structured large areas. By a thorough characterization it is shown that the electrical properties of the parallel SSPDs are comparable with those of smaller devices, as expected, proving in this way that the extended EBL process results in uniform nanostrips also in large area detectors. Furthermore, the estimated maximum count rate of the 40 × 40 μm2 parallel SSPDs was 33 MHz, showing that the parallel nanostrip configuration is much faster when compared with standard meandered serial SSPDs. The successful extension of parallel SSPDs to a large area coverage opens a new route to the use of such detectors also with multimode fibers.

Journal of Vacuum Science & Technology B Nanotechnology and Microelectronics Materials Processing Measurement and Phenomena•Apr 3, 2012•10 citations

Superconducting single photon detectors based on parallel NbN nanowires

Mikkel Ejrnaes, A. Casaburi, S. Pagano +4 more

Ultrathin NbN nanowires is the material of choice for superconducting single photon detectors (SSPD) due to the good efficiency, dark count rate and timing jitter at 1550 nm wavelength obtained. These performance parameters are achieved using nanowires a few nanometers thick and 100 nm wide patterned into a meander shape in order to achieve area coverage. The meander shape effectively makes the SSPD of a single very long nanowire in turn giving it a significant inductance which limits the maximum count rate of the detector. Recently, we demonstrated how one can exploit a cascade switch to the normal state of nanowires connected in parallel to significantly reduce the SSPD inductance and increase the signal amplitude. Here we present how one can configure SSPDs that uses multiple cascade switches to the normal state. We show how this principle can be used to expand the SSPD coverage area with a very limited increase in detector inductance with area. Finally we discuss our first results obtained with SSPD based on the multiple cascade switch principle, showing correct operation, increased operational bias range and increased signal pulse amplitudes.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Apr 29, 2011•0 citations

Operation of parallel SNSPDs at high detection rates

Matthieu Perrenoud, Misael Caloz, Emna Amri +4 more

Abstract Recent progress in the development of superconducting nanowire single-photon detectors (SNSPD) has delivered excellent performance, and their increased adoption has had a great impact on a range of applications. One of the key characteristic of SNSPDs is their detection rate, which is typically higher than other types of free-running single-photon detectors. The maximum achievable rate is limited by the detector recovery time after a detection, which itself is linked to the superconducting material properties and to the geometry of the meandered SNSPD. Arrays of detectors biased individually can be used to solve this issue, but this approach significantly increases both the thermal load in the cryostat and the need for time processing of the many signals, and this scales unfavorably with a large number of detectors. One potential scalable approach to increase the detection rate of individual detectors further is based on parallelizing smaller meander sections. In this way, a single detection temporarily disables only one subsection of the whole active area, thereby leaving the overall detection efficiency mostly unaffected. In practice however, cross-talk between parallel nanowires typically leads to latching, which prevents high detection rates. Here we show how this problem can be avoided through a careful design of the whole SNSPD structure. Using the same electronic readout as with conventional SNSPDs and a single coaxial line, we demonstrate detection rates over 200 MHz without any latching, and a fibre-coupled SDE as high as 77%, and more than 50% average SDE per photon at 50 MHz detection rate under continuous wave illumination.

Superconductor Science and Technology•Nov 9, 2020•28 citations

Operation of parallel SNSPDs at high detection rates

Matthieu Perrenoud, Misael Caloz, Emna Amri +4 more

Recent progress in the development of superconducting nanowire single-photon detectors (SNSPD) has delivered ex-cellent performance, and their increased adoption has had a great impact on a range of applications. One of the key characteristic of SNSPDs is their detection rate, which is typically higher than other types of free-running single-photondetectors. The maximum achievable rate is limited by the detector recovery time after a detection, which itself is linked to the superconducting material properties and to the geometry of the meandered SNSPD. Arrays of detectors biased individually can be used to solve this issue, but this approach significantly increases both the thermal load in the cryo-stat and the need for time processing of the many signals, and this scales unfavorably with a large number of detectors. One potential scalable approach to increase the detection rate of individual detectors further is based on parallelizing smaller meander sections. In this way, a single detection temporarily disables only one subsection of the whole active area, thereby leaving the overall detection efficiency mostly unaffected. In practice however, cross-talk between parallel nanowires typically leads to latching, which prevents high detection rates. Here we show how this problem can be avoided through a careful design of the whole SNSPD structure. Using the same electronic readout as with conventional SNSPDs and a single coaxial line, we demonstrate detection rates over 200 MHz without any latching, and a fibre-coupled SDE as high as 77%, and more than 50% average SDE per photon at 50 MHz detection rate under continuous wave illumination.

arXiv:2109.03126•Sep 7, 2021•1 citation

Improving maximum count rate of superconducting nanowire single-photon detector with small active area using series attenuator

Chaolin Lv, Weijun Zhang, Lixing You +9 more

Maximum count rate is a crucial parameter of superconducting nanowire single-photon detector (SNSPD) for quantum communication and laser communication. However, when increasing the incident photon flux, the SNSPD device with small active area is apt to latch due to the AC coupling of room temperature amplifier in the readout circuit, which limits SNSPD to reach a high count rate. We proposed a simple way by inserting an electrical attenuator in series with small-active area SNSPD to avoid the latching effect, thus improving maximum count rate effectively. The count rate with the system detection efficiency reduced by half increased by 6 times for SNSPD with an active area of Φ15 μm.

AIP Advances•Oct 1, 2018•14 citations
An analysis of different strategies for increasing the maximum count rate of superconducting single photon detectors using parallel nanowires is performed with particular emphasis on the expected behaviour when the detector area is increased. We find that for a serial connection of blocks of parallel nanowires, the maximum count rate decreases with the square root of the detector area, whereas it decreases proportional to the detector area for current meandered detectors. Using this design we estimate that a signal pulse falltime of 7.8 ns for a 84 × 84 µm2 parallel detector based on current material parameters should be obtainable. We argue that the slow decrease of count rate with detector area might permit detectors based on parallel nanowires to fully exploit the available cooling power.
Superconducting nanowire single photon detectors (SNSPDs) have been realized using an innovative parallel wire configuration. This configuration allows, at the same time, a large detection area and a fast response, with the additional advantage of large signal amplitudes. The detectors have been thoroughly characterized in terms of signal properties (amplitude, risetime and falltime), detector operation (latching and not latching) and quantum efficiency (at 850 nm). It has been shown that the parallel SNSPD is able to provide significantly higher maximum count rates for large area SNSPDs than meandered SNSPDs. Through a proper parallel wire configuration the increase in maximum count rate can be obtained without latching problems.
The authors present superconducting single photon detectors (SSPDs) based on parallel nanostrips with an area up to 40 × 40 μm2. The SSPDs presented here are based on 100 nm wide ultrathin NbN nanostrips with a filling factor of 40%. The devices are fabricated by extending the standard electron beam lithography (EBL) patterning process to those densely structured large areas. By a thorough characterization it is shown that the electrical properties of the parallel SSPDs are comparable with those of smaller devices, as expected, proving in this way that the extended EBL process results in uniform nanostrips also in large area detectors. Furthermore, the estimated maximum count rate of the 40 × 40 μm2 parallel SSPDs was 33 MHz, showing that the parallel nanostrip configuration is much faster when compared with standard meandered serial SSPDs. The successful extension of parallel SSPDs to a large area coverage opens a new route to the use of such detectors also with multimode fibers.
Ultrathin NbN nanowires is the material of choice for superconducting single photon detectors (SSPD) due to the good efficiency, dark count rate and timing jitter at 1550 nm wavelength obtained. These performance parameters are achieved using nanowires a few nanometers thick and 100 nm wide patterned into a meander shape in order to achieve area coverage. The meander shape effectively makes the SSPD of a single very long nanowire in turn giving it a significant inductance which limits the maximum count rate of the detector. Recently, we demonstrated how one can exploit a cascade switch to the normal state of nanowires connected in parallel to significantly reduce the SSPD inductance and increase the signal amplitude. Here we present how one can configure SSPDs that uses multiple cascade switches to the normal state. We show how this principle can be used to expand the SSPD coverage area with a very limited increase in detector inductance with area. Finally we discuss our first results obtained with SSPD based on the multiple cascade switch principle, showing correct operation, increased operational bias range and increased signal pulse amplitudes.
Abstract Recent progress in the development of superconducting nanowire single-photon detectors (SNSPD) has delivered excellent performance, and their increased adoption has had a great impact on a range of applications. One of the key characteristic of SNSPDs is their detection rate, which is typically higher than other types of free-running single-photon detectors. The maximum achievable rate is limited by the detector recovery time after a detection, which itself is linked to the superconducting material properties and to the geometry of the meandered SNSPD. Arrays of detectors biased individually can be used to solve this issue, but this approach significantly increases both the thermal load in the cryostat and the need for time processing of the many signals, and this scales unfavorably with a large number of detectors. One potential scalable approach to increase the detection rate of individual detectors further is based on parallelizing smaller meander sections. In this way, a single detection temporarily disables only one subsection of the whole active area, thereby leaving the overall detection efficiency mostly unaffected. In practice however, cross-talk between parallel nanowires typically leads to latching, which prevents high detection rates. Here we show how this problem can be avoided through a careful design of the whole SNSPD structure. Using the same electronic readout as with conventional SNSPDs and a single coaxial line, we demonstrate detection rates over 200 MHz without any latching, and a fibre-coupled SDE as high as 77%, and more than 50% average SDE per photon at 50 MHz detection rate under continuous wave illumination.
Recent progress in the development of superconducting nanowire single-photon detectors (SNSPD) has delivered ex-cellent performance, and their increased adoption has had a great impact on a range of applications. One of the key characteristic of SNSPDs is their detection rate, which is typically higher than other types of free-running single-photondetectors. The maximum achievable rate is limited by the detector recovery time after a detection, which itself is linked to the superconducting material properties and to the geometry of the meandered SNSPD. Arrays of detectors biased individually can be used to solve this issue, but this approach significantly increases both the thermal load in the cryo-stat and the need for time processing of the many signals, and this scales unfavorably with a large number of detectors. One potential scalable approach to increase the detection rate of individual detectors further is based on parallelizing smaller meander sections. In this way, a single detection temporarily disables only one subsection of the whole active area, thereby leaving the overall detection efficiency mostly unaffected. In practice however, cross-talk between parallel nanowires typically leads to latching, which prevents high detection rates. Here we show how this problem can be avoided through a careful design of the whole SNSPD structure. Using the same electronic readout as with conventional SNSPDs and a single coaxial line, we demonstrate detection rates over 200 MHz without any latching, and a fibre-coupled SDE as high as 77%, and more than 50% average SDE per photon at 50 MHz detection rate under continuous wave illumination.
Maximum count rate is a crucial parameter of superconducting nanowire single-photon detector (SNSPD) for quantum communication and laser communication. However, when increasing the incident photon flux, the SNSPD device with small active area is apt to latch due to the AC coupling of room temperature amplifier in the readout circuit, which limits SNSPD to reach a high count rate. We proposed a simple way by inserting an electrical attenuator in series with small-active area SNSPD to avoid the latching effect, thus improving maximum count rate effectively. The count rate with the system detection efficiency reduced by half increased by 6 times for SNSPD with an active area of Φ15 μm.