Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

AIP conference proceedings

Progress on millimeter wave Josephson junction mixers

Y. Taur, Anthony R. Kerr

Published Jan 1, 1978• 1 citation
Publisher

Abstract

Preset, recyclable Nb point contacts are tested as low‐noise Josephson mixers at a signal frequency of 115 GHz. The best result achieved is a mixer noise temperature (single sideband) of 120 K with unity conversion efficiency (SSB) for a junction at 6 K. Variation of mixer properties with temperature and other parameters is presented.
DOI
10.1063/1.31348

Related papers

Low-noise Josephson mixers at 115 GHz using recyclable point contacts

Y. Taur, Anthony R. Kerr

Thermally recyclable Nb point-contact Josephson junctions are investigated as low-noise mixers with an external local oscillator at 115 GHz. The best single sideband mixer noise temperature achieved is 140 (±20) K with a (SSB) conversion loss of 2.4 (±0.5) dB. Such rugged junctions are suitable for use in practical receivers and should give unprecedented sensitivity at the shorter millimeter wavelengths.

Applied Physics Letters•Jun 1, 1978•32 citations

Noise in Josephson mm-wave mixers

J. H. Claassen, Yuan Taur, P. L. Richards

Point contact Josephson junctions can function as millimeter wave heterodyne mixers with conversion gain. The best results achieved thus far show a single sideband conversion gain of 1.3 and a mixer contribution to the system noise temperature of 54$sup 0$K. Both of these results are approximately 5 times better than the best published figures for cooled Schottky barrier diode mixers operated at the same frequency. The measured noise for a variety of junctions can be expressed as a universal function of the normalized rf frequency $Omega$ = h$omega$/2eI/sub c/R. It is about a factor 2 larger than the calculated noise arising from the thermal noise in the junction shunt resistance, R. The noise calculation was done for the resistively shunted junction model using an analog junction simulator. (auth)

•Mar 1, 1975•0 citations

A Low-Noise 47-GHz Mixer Using a Permanent Josephson Junction

JOCHEN EDRICH

A new method to produce permanent Josephson junctions for millimeter-wave mixers is reported. In contrast to conventional point contacts which are mechanically unstable and require adjustments after each cooldown, these point contact junctions are set at room temperature, stay mechanically stable, and can be temperature cycled without readjustments. Using these junctions in a modified Sharpless wafer mixer mount, a single-sideband noise temperature of 71 K was measured at 47 GHz. Based on these results, system noise temperatures of less than 100 K are predicted for practical broad-band radiometers, RADAR, and communications receivers up to at least 100 GHz

IEEE Transactions on Microwave Theory and Techniques•Nov 1, 1976•7 citations

Noise in Josephson effect mm-wave mixers

J. H. Claassen, Y. Taur, P. L. Richards

We have recently shown that point contact Josephson junctions can function as millimeter wave heterodyne mixers with conversion gain. The best results achieved thus far show a single sideband conversion gain of 1.3 and a mixer contribution to the system noise temperature of 54K. Both of these results are ∼ 5 times better than the best published figures for cooled Schottky barrier diode mixers operated at the same frequency. The measured noise for a variety of junctions can be expressed as a universal function of the normalized rf frequency\Omega = \hbar \omega/2eI_{c}R. It is about a factor 2 larger than the calculated noise arising from the thermal noise in the junction shunt resistance R. The noise calculation was done for the resistively shunted junction model using an analog junction simulator.

IEEE Transactions on Magnetics•Mar 1, 1975•1 citation

Noise in Josephson effect mm-wave mixers

J. H. Claassen, Y. Taur, P. L. Richards

We have recently shown that point contact Josephson junctions can function as millimeter wave heterodyne mixers with conversion gain. The best results achieved thus far show a single sideband conversion gain of 1.3 and a mixer contribution to the system noise temperature of 54K. Both of these results are ∼ 5 times better than the best published figures for cooled Schottky barrier diode mixers operated at the same frequency. The measured noise for a variety of junctions can be expressed as a universal function of the normalized rf frequency \Omega = \hbar \omega/2eI_{c}R . It is about a factor 2 larger than the calculated noise arising from the thermal noise in the junction shunt resistance R. The noise calculation was done for the resistively shunted junction model using an analog junction simulator.

•Sep 1, 1974•0 citations

Conversion gain in a Josephson effect mixer

Y. Taur, J. H. Claassen, P. L. Richards

The measured performance of Nb–Nb point contact Josephson junctions used as 36-GHz microwave mixers is in good agreement with the predictions of the resistively shunted junction model. Conversion efficiencies greater than unity are attained, with mixer noise temperatures comparable with the best competing devices.

Applied Physics Letters•Jan 15, 1974•54 citations
Point contact Josephson junctions can function as millimeter wave heterodyne mixers with conversion gain. The best results achieved thus far show a single sideband conversion gain of 1.3 and a mixer contribution to the system noise temperature of 54sup0sup 0sup0K. Both of these results are approximately 5 times better than the best published figures for cooled Schottky barrier diode mixers operated at the same frequency. The measured noise for a variety of junctions can be expressed as a universal function of the normalized rf frequency OmegaOmegaOmega = homegaomegaomega/2eI/sub c/R. It is about a factor 2 larger than the calculated noise arising from the thermal noise in the junction shunt resistance, R. The noise calculation was done for the resistively shunted junction model using an analog junction simulator. (auth)
A new method to produce permanent Josephson junctions for millimeter-wave mixers is reported. In contrast to conventional point contacts which are mechanically unstable and require adjustments after each cooldown, these point contact junctions are set at room temperature, stay mechanically stable, and can be temperature cycled without readjustments. Using these junctions in a modified Sharpless wafer mixer mount, a single-sideband noise temperature of 71 K was measured at 47 GHz. Based on these results, system noise temperatures of less than 100 K are predicted for practical broad-band radiometers, RADAR, and communications receivers up to at least 100 GHz
We have recently shown that point contact Josephson junctions can function as millimeter wave heterodyne mixers with conversion gain. The best results achieved thus far show a single sideband conversion gain of 1.3 and a mixer contribution to the system noise temperature of 54K. Both of these results are ∼ 5 times better than the best published figures for cooled Schottky barrier diode mixers operated at the same frequency. The measured noise for a variety of junctions can be expressed as a universal function of the normalized rf frequency\Omega = \hbar \omega/2eI_{c}R. It is about a factor 2 larger than the calculated noise arising from the thermal noise in the junction shunt resistance R. The noise calculation was done for the resistively shunted junction model using an analog junction simulator.
We have recently shown that point contact Josephson junctions can function as millimeter wave heterodyne mixers with conversion gain. The best results achieved thus far show a single sideband conversion gain of 1.3 and a mixer contribution to the system noise temperature of 54K. Both of these results are ∼ 5 times better than the best published figures for cooled Schottky barrier diode mixers operated at the same frequency. The measured noise for a variety of junctions can be expressed as a universal function of the normalized rf frequency \Omega = \hbar \omega/2eI_{c}R . It is about a factor 2 larger than the calculated noise arising from the thermal noise in the junction shunt resistance R. The noise calculation was done for the resistively shunted junction model using an analog junction simulator.