Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Towards the quantum limit: A Single Electron Transistor analysis

Zhongqing Ji

Published Jan 1, 2008• 1 citation
OpenAlex

Abstract

The Single Electron Transistor (SET), especially its variation the radio frequency single electron transistor (RF-SET), is a fast and ultra-sensitive electrometer working in the vicinity of the quantum limit. In this thesis, the theory and techniques related to the SET in the normal state and the superconducting state are introduced The thesis focuses especially on our efforts of improving the sensitivity of superconducting RF-SET, including: the design and fabrication of an all superconducting near loss-less matching network for improving the RF modulation, our early investigation of the sensitivity and linearity of a superconducting SET (S-SET) subject to quantum fluctuations of quasiparticles and Cooper pairs under different tunneling mechanisms, and our recent work approaching the quantum sensitivity limit using a double Josephson quasiparticle (DJQP) cycle of a S-SET. Using an effective bath description, we have found that the S-SET provides damping of the resonator modes proportional to its differential conductance, and has an effective temperature that can be well below both the ambient temperature and the energy scale of the bias voltage. In the region of negative differential conductance (NDC), the S-SET shows negative damping and a negative temperature. In the final part of the thesis, I have demonstrated our first application of an RF-SET for real-time detection of electron tunneling through a quantum dot.

Related papers

Study of the radio frequency single electron transistor: Principles and applications

Zhongqing Ji

This thesis will discuss the principles, techniques and applications of the Radio Frequency Single Electron Transistor (RF-SET). In the first part, the operating principles of Single Electron Transistors (SETS) in the normal and superconducting states will be introduced. The general techniques of fabricating and calibrating SETs will also be introduced. In the second part, two of our recent experiments are reviewed. One is related to the sensitivity and linearity of superconducting RF-SETs. We found that the RF-SET achieves the best balance of charge sensitivity and linearity in the subgap regime, as opposed to the usual preferred working point in the above-gap regime. The second experiment relates to the real-time counting of single electrons. We demonstrated that the RF-SET can be used as a fast and ultra-sensitive electrometer which can even detect tunneling of a single electron inside a tunable quantum dot (QD) formed in a two dimensional electron gas (2DEG).

•Jan 1, 2005•0 citations

Double quantum dot coupled to a radio-frequency single-electron transistor: Quantum measurement and back action

Madhu Thalakulam

The radio-frequency superconducting single electron transistor (RF-SET) is a highly sensitive and fast electrometer operating near the quantum limit. The back-action current noise of the SET induces voltage fluctuations on the system it is coupled to, dephasing its charge states. Here we propose to study the back action of the RF-SET by means of a double quantum dot (DQD) and, an RF-SET electrostatically coupled to one of the two dots. The inelastic current through the DQD is very sensitive to the spectral density of the voltage fluctuations in the nearby environment. By properly choosing the dot size and inter-dot tunnel barrier thickness, one can cause inelastic process to dominate the transport processes. A measurement of the inelastic current through the double dot system can then be used to calculate the spectral density of noise associated with the RF-SET and hence its back action. The design, fabrication and characterization of an RF-SET/DQD system is discussed in this work. Real-time studies of electron dynamics in coupled dots are also addressed.

•Jan 1, 2004•0 citations

The Single Cooper Pair Box - a Quantum-Mechanical Electronic Circuit

David Gunnarsson

In this thesis the single Cooper pair box (SCB) is investigated with a radio frequency single electron transistor (RF-SET). The RF-SET is used as an electrometer to detect the charge of the SCB. The SCB can be regarded as a quantum two-level system and could therefore be a possible qubit. Both the SCB and the RF-SET have been fabricated with e-beam lithography followed by two-angle shadow evaporation of aluminium. The system has been measured in a dilution refrigerator at temperatures of ~30 mK. A charge sensitivity of 2.3 μe/square root of Hz was measured for an optimized RF-SET with a bandwidth of 7 MHz, operated in the superconducting state. In a phase sensitive measurement of the RF-SET reflected signal, the gate dependence of the quantum capacitance, due to avoided level crossing, was detected in a superconducting SET. Coulomb staircases for the SCB were obtained by changing the charge of the SCB by ramping a gate voltage and continuously measuring the charge with the RF-SET. To prevent quasiparticle poisoning of the SCB island, we have used a method of graded gaps. Here we exploit the greater reduction of the superconducting gap for the connecting leads with an external magnetic field applied, resulting in a higher gap for the island. This creates an effective barrier against quasiparticle tunnelling. The charging energy and the Josephson coupling energy of the SCB were measured with microwave spectroscopy. The SCBs were fabricated in a SQUID geometry, which made it possible to tune the Josephson coupling energy of the box. This tuning was verified through microwave spectroscopy. The effect of tuning could also be seen in the pure 2e Coulomb staircase, as a predicted smearing of the staircase, which was in excellent agreement with the independent spectroscopy data. Coherent quantum oscillation of the SCB charge state was measured by applying nonadiabatic DC-pulses to the SCB gate. The measured amplitude of the charge oscillations was higher than 70%. The deviation from 100% can be explained by the initial charge state purity and the finite rise time of the pulses. The longest decoherence time of the charge oscillations was T2 = 9 ns at the charge degeneracy point. It was found to be limited by relaxation. Away from the degeneracy point the decoherence time was limited by pure dephasing, due to low frequency charge fluctuators.

•Jan 1, 2005•0 citations

Single-electron transistor: Effects of the environment and detecting electron motion in real time

Wei Dong Lu

This thesis will be divided into two parts. In the first part, theory and results of a novel system in which a superconducting single-electron transistor (S-SET) coupled to a two-dimensional electron gas (2DEG) serving as a tunable electromagnetic environment for the S-SET will be discussed, including effects of dissipation, resonant tunneling with photon emission, and photon-assisted tunneling. In the second part, we discuss the techniques for which the SET is incorporated in an RF resonant circuit, resulting in an ultra high charge sensitivity and bandwidth. After the 2DEG is confined into a quantum dot, random telegraph signals (RTS) caused by individual electrons tunneling on and off the dot have been observed. In the equilibrium configuration, the occupational probabilities of the charge states of the dot can be directly measured from the RTS and were found to follow a Fermi distribution. In the non-equilibrium configuration, the RTS correctly detected the onset of the current through the dot.

•Jan 1, 2003•0 citations

Quantum Noise, Effective Temperature, and Damping in a Superconducting Single-Electron Transistor

W. W. Xue, Zhongqing Ji, Pan, Feng +2 more

We have directly measured the quantum noise of a superconducting single-electron transistor (S-SET) embedded in a microwave resonator consisting of a superconducting LC tank circuit. Using an effective bath description, we find that the S-SET provides damping of the resonator modes proportional to its differential conductance and has an effective temperature that depends strongly on the S-SET bias conditions. In the vicinity of a double Cooper pair resonance, when both resonances are red detuned the S-SET effective temperature can be well below both the ambient temperature and the energy scale of the bias voltage. When blue detuned, the S-SET shows negative differential conductivity,

arXiv:0805.1037•May 7, 2008•0 citations

The Radio-Frequency Single-Electron Transistor (RF-SET): A Fast and Ultrasensitive Electrometer

R. J. Schoelkopf, Paula Wahlgren, A. A. Kozhevnikov +2 more

A new type of electrometer is described that uses a single-electron transistor (SET) and that allows large operating speeds and extremely high charge sensitivity. The SET readout was accomplished by measuring the damping of a 1.7-gigahertz resonant circuit in which the device is embedded, and in some ways is the electrostatic "dual" of the well-known radio-frequency superconducting quantum interference device. The device is more than two orders of magnitude faster than previous single-electron devices, with a constant gain from dc to greater than 100 megahertz. For a still-unoptimized device, a charge sensitivity of 1.2 x 10(-5) e/hertz was obtained at a frequency of 1.1 megahertz, which is about an order of magnitude better than a typical, 1/f-noise-limited SET, and corresponds to an energy sensitivity (in joules per hertz) of about 41 Planck's over 2pi.

Science•May 22, 1998•776 citations
The Single Electron Transistor (SET), especially its variation the radio frequency single electron transistor (RF-SET), is a fast and ultra-sensitive electrometer working in the vicinity of the quantum limit. In this thesis, the theory and techniques related to the SET in the normal state and the superconducting state are introduced The thesis focuses especially on our efforts of improving the sensitivity of superconducting RF-SET, including: the design and fabrication of an all superconducting near loss-less matching network for improving the RF modulation, our early investigation of the sensitivity and linearity of a superconducting SET (S-SET) subject to quantum fluctuations of quasiparticles and Cooper pairs under different tunneling mechanisms, and our recent work approaching the quantum sensitivity limit using a double Josephson quasiparticle (DJQP) cycle of a S-SET. Using an effective bath description, we have found that the S-SET provides damping of the resonator modes proportional to its differential conductance, and has an effective temperature that can be well below both the ambient temperature and the energy scale of the bias voltage. In the region of negative differential conductance (NDC), the S-SET shows negative damping and a negative temperature. In the final part of the thesis, I have demonstrated our first application of an RF-SET for real-time detection of electron tunneling through a quantum dot.
This thesis will discuss the principles, techniques and applications of the Radio Frequency Single Electron Transistor (RF-SET). In the first part, the operating principles of Single Electron Transistors (SETS) in the normal and superconducting states will be introduced. The general techniques of fabricating and calibrating SETs will also be introduced. In the second part, two of our recent experiments are reviewed. One is related to the sensitivity and linearity of superconducting RF-SETs. We found that the RF-SET achieves the best balance of charge sensitivity and linearity in the subgap regime, as opposed to the usual preferred working point in the above-gap regime. The second experiment relates to the real-time counting of single electrons. We demonstrated that the RF-SET can be used as a fast and ultra-sensitive electrometer which can even detect tunneling of a single electron inside a tunable quantum dot (QD) formed in a two dimensional electron gas (2DEG).
The radio-frequency superconducting single electron transistor (RF-SET) is a highly sensitive and fast electrometer operating near the quantum limit. The back-action current noise of the SET induces voltage fluctuations on the system it is coupled to, dephasing its charge states. Here we propose to study the back action of the RF-SET by means of a double quantum dot (DQD) and, an RF-SET electrostatically coupled to one of the two dots. The inelastic current through the DQD is very sensitive to the spectral density of the voltage fluctuations in the nearby environment. By properly choosing the dot size and inter-dot tunnel barrier thickness, one can cause inelastic process to dominate the transport processes. A measurement of the inelastic current through the double dot system can then be used to calculate the spectral density of noise associated with the RF-SET and hence its back action. The design, fabrication and characterization of an RF-SET/DQD system is discussed in this work. Real-time studies of electron dynamics in coupled dots are also addressed.
In this thesis the single Cooper pair box (SCB) is investigated with a radio frequency single electron transistor (RF-SET). The RF-SET is used as an electrometer to detect the charge of the SCB. The SCB can be regarded as a quantum two-level system and could therefore be a possible qubit. Both the SCB and the RF-SET have been fabricated with e-beam lithography followed by two-angle shadow evaporation of aluminium. The system has been measured in a dilution refrigerator at temperatures of ~30 mK. A charge sensitivity of 2.3 μe/square root of Hz was measured for an optimized RF-SET with a bandwidth of 7 MHz, operated in the superconducting state. In a phase sensitive measurement of the RF-SET reflected signal, the gate dependence of the quantum capacitance, due to avoided level crossing, was detected in a superconducting SET. Coulomb staircases for the SCB were obtained by changing the charge of the SCB by ramping a gate voltage and continuously measuring the charge with the RF-SET. To prevent quasiparticle poisoning of the SCB island, we have used a method of graded gaps. Here we exploit the greater reduction of the superconducting gap for the connecting leads with an external magnetic field applied, resulting in a higher gap for the island. This creates an effective barrier against quasiparticle tunnelling. The charging energy and the Josephson coupling energy of the SCB were measured with microwave spectroscopy. The SCBs were fabricated in a SQUID geometry, which made it possible to tune the Josephson coupling energy of the box. This tuning was verified through microwave spectroscopy. The effect of tuning could also be seen in the pure 2e Coulomb staircase, as a predicted smearing of the staircase, which was in excellent agreement with the independent spectroscopy data. Coherent quantum oscillation of the SCB charge state was measured by applying nonadiabatic DC-pulses to the SCB gate. The measured amplitude of the charge oscillations was higher than 70%. The deviation from 100% can be explained by the initial charge state purity and the finite rise time of the pulses. The longest decoherence time of the charge oscillations was T2 = 9 ns at the charge degeneracy point. It was found to be limited by relaxation. Away from the degeneracy point the decoherence time was limited by pure dephasing, due to low frequency charge fluctuators.
This thesis will be divided into two parts. In the first part, theory and results of a novel system in which a superconducting single-electron transistor (S-SET) coupled to a two-dimensional electron gas (2DEG) serving as a tunable electromagnetic environment for the S-SET will be discussed, including effects of dissipation, resonant tunneling with photon emission, and photon-assisted tunneling. In the second part, we discuss the techniques for which the SET is incorporated in an RF resonant circuit, resulting in an ultra high charge sensitivity and bandwidth. After the 2DEG is confined into a quantum dot, random telegraph signals (RTS) caused by individual electrons tunneling on and off the dot have been observed. In the equilibrium configuration, the occupational probabilities of the charge states of the dot can be directly measured from the RTS and were found to follow a Fermi distribution. In the non-equilibrium configuration, the RTS correctly detected the onset of the current through the dot.
We have directly measured the quantum noise of a superconducting single-electron transistor (S-SET) embedded in a microwave resonator consisting of a superconducting LC tank circuit. Using an effective bath description, we find that the S-SET provides damping of the resonator modes proportional to its differential conductance and has an effective temperature that depends strongly on the S-SET bias conditions. In the vicinity of a double Cooper pair resonance, when both resonances are red detuned the S-SET effective temperature can be well below both the ambient temperature and the energy scale of the bias voltage. When blue detuned, the S-SET shows negative differential conductivity,
A new type of electrometer is described that uses a single-electron transistor (SET) and that allows large operating speeds and extremely high charge sensitivity. The SET readout was accomplished by measuring the damping of a 1.7-gigahertz resonant circuit in which the device is embedded, and in some ways is the electrostatic "dual" of the well-known radio-frequency superconducting quantum interference device. The device is more than two orders of magnitude faster than previous single-electron devices, with a constant gain from dc to greater than 100 megahertz. For a still-unoptimized device, a charge sensitivity of 1.2 x 10(-5) e/hertz was obtained at a frequency of 1.1 megahertz, which is about an order of magnitude better than a typical, 1/f-noise-limited SET, and corresponds to an energy sensitivity (in joules per hertz) of about 41 Planck's over 2pi.