The atom laser has long been a holy grail within atom physics and with the creation of an atom laser we hope to bring a similar revolution in to the field of atom optics. With the creation of the Bose-Einstein Condensate (BEC) in 1995 the path to an atom laser was initiated. An atom laser is continues source of BEC. In a Bose condensate all the atoms occupy the same quantum state and can be described by the same wave function and phase. With an atom laser the De Broglie wavelength of atoms can be much smaller than the wavelength of light. Due to the ultimate control over the atoms the atom laser is very interesting for atom optics, lithography, metrology, etching and deposition of atoms on a surface. All previous atom lasers have been created from atoms coupled out from an existing Bose-Einstein Condensate. There are different approaches but common to them all is that the duration of the output of the atom laser is limited by the size of the initial BEC and they all have a low flux. This leaves the quest to build a continuous high flux atom laser. An alternative approach to a continuous BEC beam is to channel a continuous ultra cold atomic beam into a magnetic guide and then cool this beam down to degeneracy. Cooling down a continuous beam of atoms faces three large problems: The collision rate has to be large enough for effective rethermalization, since evaporative cooling in 2D is not as effective as in 3D and a large thermal conductivity due to atoms with a high angular momentum causes heating downstream in the guide. We have built a 4 meter magnetic guide that is placed on a downward slope with a magnetic barrier in the end. In the guide we load packets of ultra cold rubidium atoms with a frequency rate large enough for the packets to merge together to form a continuous atomic beam. The atomic beam is supersonic and when the beam reaches the end barrier it will return and collide with itself. The collisions lowers the velocity of the beam into subsonic velocities and a shock wave is created between the two velocity regions. In order to conserve number of particle, momentum and enthalpy the density of the atomic beam passing through the shock wave must increase. We have build such a shock wave in an atomic beam and observed the density increase due to this. As an extra feature having a subsonic beam on a downward slope adds an extra density increase due to gravitational compression. Loading ultra cold atoms into a 3D trap from the dense subsonic beam overcomes the problem with 2D cooling and thermal conductivity. This was done and evaporative cooling was applied creating an unprecedented large number rubidium BEC.
The atom laser has long been a holy grail within atom physics and with the creation of an atom laser we hope to bring a similar revolution in to the field of atom optics. With the creation of the Bose-Einstein Condensate (BEC) in 1995 the path to an atom laser was initiated. An atom laser is continues source of BEC. In a Bose condensate all the atoms occupy the same quantum state and can be described by the same wave function and phase. With an atom laser the De Broglie wavelength of atoms can be much smaller than the wavelength of light. Due to the ultimate control over the atoms the atom laser is very interesting for atom optics, lithography, metrology, etching and deposition of atoms on a surface. All previous atom lasers have been created from atoms coupled out from an existing Bose-Einstein Condensate. There are different approaches but common to them all is that the duration of the output of the atom laser is limited by the size of the initial BEC and they all have a low flux. This leaves the quest to build a continuous high flux atom laser. An alternative approach to a continuous BEC beam is to channel a continuous ultra cold atomic beam into a magnetic guide and then cool this beam down to degeneracy. Cooling down a continuous beam of atoms faces three large problems: The collision rate has to be large enough for effective rethermalization, since evaporative cooling in 2D is not as effective as in 3D and a large thermal conductivity due to atoms with a high angular momentum causes heating downstream in the guide. We have built a 4 meter magnetic guide that is placed on a downward slope with a magnetic barrier in the end. In the guide we load packets of ultra cold rubidium atoms with a frequency rate large enough for the packets to merge together to form a continuous atomic beam. The atomic beam is supersonic and when the beam reaches the end barrier it will return and collide with itself. The collisions lowers the velocity of the beam into subsonic velocities and a shock wave is created between the two velocity regions. In order to conserve number of particle, momentum and enthalpy the density of the atomic beam passing through the shock wave must increase. We have build such a shock wave in an atomic beam and observed the density increase due to this. As an extra feature having a subsonic beam on a downward slope adds an extra density increase due to gravitational compression. Loading ultra cold atoms into a 3D trap from the dense subsonic beam overcomes the problem with 2D cooling and thermal conductivity. This was done and evaporative cooling was applied creating an unprecedented large number rubidium BEC.
In 1925, Einstein predicted the condensation of bosons into the ground state of the system for low (but finite) temperatures. Several phenomena, including superfluidity and superconductivity have been associated with Bose-Einstein condensation, but these systems interact strongly with their environment and pure Bose-Einstein condensation could not be established. It took 70 years, in which time the laser was discovered, and laser cooling techniques to manipulate atoms in a dilute atomic gas, before Bose-Einstein condensation in dilute atomic gases could be demonstrated in 1995. In the first condensation experiments, BECs were created in a magnetic trap. Since in a magnetic trap not all mF states of the atom can be trapped simultaneously, thereby limiting the number of experiments that can be done, other ways of trapping and generating BECs were sought and found. In 2001, the first all-optical BEC was made, where the dipole force was used to trap atoms in the crossing of two far red detuned laser beams. In an optical dipole trap not only atoms in different internal states can be trapped, but also different atomic species simultaneously. In this thesis, the formation of an all-optical Bose-Einstein condensate with rubidium atoms is presented. Conventional all-optical BECs are usually created in high power CO2 laser dipole traps, or have complicated laser cooling schemes and complex dipole trap setups. In our simple and straightforward setup, we load rubidium atoms from a magneto-optical trap into a crossed optical dipole trap created by a single frequency Yb:YAG laser with a wavelength at 1030 nm. The small wavelength allows for a small diffraction limit, and permits us to use standard optical materials, thus making the experimental setup cost effective. Other attempts to achieve Bose-Einstein condensation in a multi-mode (frequency) fiber laser at 1064 nm failed, because the atom loss was quite high. It is assumed that the multi-mode character of the fiber laser induces Raman transitions in rubidium atoms, thereby heating them. We can trap about ∼ 5E7 atoms in a single beam dipole trap out of ∼ 5E9 atoms trapped in theMOT, and ∼ 350,000 atoms can be trapped in a crossed beam dipole trap due to the smaller trap volume. 70% of the atoms in the dipole trap is optically pumped into one mF state. Quantum degeneracy is reached by evaporatively cooling the atoms in the crossed dipole trap by ramping down the laser power with three linear ramps. We can independently change the power of each beam by an AOM. This allows us to use one beam as an atom waveguide for future experiments. After evaporation, we typically have about 10,000 atoms at a temperature below the critical temperature. We have proved Bose-Einstein condensation by using the anisotropic expansion of a quantum degenerate gas trapped in an anisotropic potential. The aspect ratio of our atom cloud changed during a time of flight from 0.7 to 1.2 in 10 ms, thus proving that we have reached quantum degeneracy. We have about 5,000 condensed atoms in our optical dipole trap at a temperature less than 100 nK. The remaining atoms are thermal. Bose-Einstein condensation is obtained within 8 s, and we can repeat the experiment every 30 s. It should be mentioned that the Bose-Einstein experiment was moved from the ”Leibniz Universität Hannover” to the ”Technische Universität Darmstadt”, and had to be completely rebuilt. All-optical Bose-Einstein condensation was reached within one year after the move. Our Bose-Einstein condensation setup presents an ideal starting point for using our condensates in combination with miniaturized atom optical setups based on our novel microfabricated optical elements. With our microlenses, we can create a number of possible dipole trap configurations, such as the dipole trap array or the cylindrical microlens array. Using microlenses in miniaturized atom optical setups opens a completely new field of coherent atom optics. Also because the tight confinement of the microtraps allows us to load a 3D BEC, a 1D BEC, or a Tonks-Girardeau gas in the micropotentials depending on the density.
This thesis examines two complimentary methods for the laser cooling of a magnetically guided ultra-cold atom beam. If combined, these methods could serve as a starting point for high-through put and possibly even continuous production of Bose-Einstein condensates. First, a mechanism is outlined to harvest ultra cold atoms from a magnetically guided atom beam into an optical dipole trap. A continuous loading scheme is described that dissipates the directed kinetic energy of a captured atom via deceleration by a magnetic potential barrier followed by optical pumping to the energetically lowest Zeeman sublevel. The application of this scheme to the transfer of ultra cold chromium atoms from a magnetically guided atom beam into a deep optical dipole trap is investigated via numerical simulations of the loading process. Based on the results of the theoretical studies the feasibility and the efficiency of our loading scheme, including the realisation of a suitable magnetic field configuration, are analysed. Second, experiments were conducted on the transverse laser cooling of a magnetically guided beam of ultra cold chromium atoms. Radial compression by a tapering of the guide is employed to adiabatically heat the beam. Inside the tapered section heat is extracted from the atom beam by a two-dimensional optical molasses perpendicular to it, resulting in a significant increase of atomic phase space density. A magnetic offset field is applied to prevent optical pumping to untrapped states. Our results demonstrate that by a suitable choice of the magnetic offset field, the cooling beam intensity and detuning, atom losses and longitudinal heating can be avoided. Final temperatures below 65 µK have been achieved, corresponding to an increase of phase space density in the guided beam by more than a factor of 30.
Optical trapping as a viable means of exploring the physics of ultracold dilute atomic gases has revealed a new spectrum of physical phenomena. In particular, macroscopic and sudden occupation of the ground state below a critical temperature—-a phenomenon known as Bose-Einstein condensation—-has become an even richer system for the study of quantum mechanics, ultracold collisions, and many-body physics in general. Optical trapping liberates the spin degree of the BEC, making the order parameter vectorial (‘spinor BEC’), as opposed to the scalar order of traditional magnetically trapped condensates. The work described within is divided into two main efforts. The first encompasses the all-optical creation of a Bose-Einstein condensate in rubidium vapor. An all-optical path to spinor BEC (as opposed to transfer to an optical trap from a magnetic-trap condensate) was desired both for the simplicity of the experimental setup and also for the potential gains in speed of creation; evaporative cooling, the only known path to dilute-gas condensation, works only as efficiently as the rate of elastic collisions in the gas, a rate that starts out much higher in optical traps. The first all-optical BEC was formed elsewhere in 2001; the years following saw many groups worldwide seeking to create their own version. Our own all-optical spinor BEC, made with a single-beam dipole trap formed by a focused CO₂ laser, is described here, with particular attention paid to trap loading, measurement of trap parameters, and the use of a novel 780 nm high-power laser system. The second part describes initial experiments performed with the nascent condensate. The spinor properties of the condensate are documented, and a measurement is made of the density-dependent rate of spin mixing in the condensate. In addition, we demonstrate a novel dual-beam atom laser formed by outcoupling oppositely polarized components of the condensate, whose populations have been coherently evolved through spin dynamics. We drive coherent spin-mixing evolution through adiabatic compression of the initially weak trap. Such dual beams, nominally number-correlated through the angular momentum-conserving collision m=0 + m=0 ⇌ m=+1 + m=-1 have been proposed as tools to explore entanglement and squeezing in Bose-Einstein condensates.
In the last decades, experimental access to the quantum regime has been gained in a large variety of systems, including dilute ultracold gases, trapped ions, micromechanical oscillators, superconducting circuits, and many more.These systems allow for such exciting applications as quantum computing and communication, quantum metrology and quantum simulation.A physical system's quantum mechanical features can only be revealed by cooling it until the thermal excitations are negligible.To date, the coldest temperatures are reached with ultracold gases by a combination of laser cooling and evaporation, inherently producing individual ensembles.However, many applications can greatly benefit from a continuous source of ultracold atoms, for example sympathetic cooling of molecules or nanoscopic objects.Ideally, this cooling source operates without light, as most molecules have a rich internal structure and can absorb photons of many wavelengths.Another promising application of continuous sources of ultracold matter is atom interferometry.Such interferometers perform measurements of inertial forces, time and gravity.Currently, each cold sample is destroyed by its evaluation and the measurement is interrupted by the preparation of a new samples.Continuous sources can help to eliminate this restriction.So far, no dark and continuous sources exist in the microkelvin regime.This thesis presents the first preparation of such an ultracold atom cloud which is continuously replenished and protected from light.The continuously refilled reservoir is prepared by loading a magnetically guided atom beam into an elongated magnetic trapping potential.This static potential has an entrance barrier which allows atoms from a guided beam to enter the trap.Once in the trap, the atoms undergo collisions and redistribute their kinetic energy.Those gaining energy can escape again, but those losing energy are trapped.A steady state with 3.8 × 10 7 atoms atoms at a temperature of 102 µK is reached and maintained.The setup of the continuous loading scheme is described in this thesis.A key component is a mesoscopic atom chip which produces all magnetic fields for the continuous loading scheme.The initial atom source is a high-flux double magneto-optical trap system.An atomic beam is created out of the precooled atoms and guided to the static trap through a stray light protection allowing for a dark retrapping region.The cooling scheme does not rely on any specific atomic properties of the atoms and can thus be applied to a wide range of particles.The results offer exciting perspectives for an application as a continuous source of ultracold atoms, either as a coolant for sympathetic cooling or as a resource for metrology.
We present a guided atom laser. A Bose-Einstein condensate (BEC) is created in a crossed hybrid magnetic and an elongated optical trap, which acts as a matterwave guide. Atoms are extracted from the BEC by radio frequency (rf) outcoupling and then guided in the horizontal optical matterwave guide. This method allows to control the acceleration of the beam and to achieve large de Broglie wavelength. We also measure the longitudinal energy of the guided atom laser using atom optical elements based on a blue light barrier.
The continuous injection and propagation of a cold atomic beam in a 1.7 m long high-gradient (up to 2.7 kG/cm) magnetic guide is demonstrated. Continuous injection is accomplished by side-loading a magnetic guide with atoms from a sequence of two modified magneto-optical traps. In the high-gradient portion of the guide, the guided atomic beam has a transverse temperature of 420 muK +/- 40 muK, a longitudinal temperature of 1 mK, and an average velocity of order 1 m/s. Essential for the characterization of this steady-state atomic beam, imaging methods compatible with the high field-gradients associated with this magnetic guide have been investigated and developed. By utilizing a probe laser tuned to an open transition, the fluorescence yield per atom is largely fixed throughout the trap volume, independent of the trapping field. This enables a reliable conversion of fluorescence images into atomic-density profiles. Using a fixed radio-frequency (nurf) current coupled directly onto the guide wires, continuous and selective removal of atoms with a transverse energy exceeding hnurf is demonstrated. This removal scheme is the essence of an rf filter, where the number of modes occupied by the atomic flow is reduced. Through sufficient rf-filtering, a near-single-mode guided atomic beam should be achievable, enabling basic atom-interferometric experiments. The extension of this fixed-frequency removal of atoms for continuous position-resolved evaporative cooling in a long magnetic guide is outlined. Employing an innovative gridless technique for performing Direct Simulation of rarefied gas dynamics via Monte Carlo (DSMC), the evaporative cooling process in a guided atomic beam has been simulated. Both fixed-frequency as well as variable-frequency evaporative cooling layouts have been explored and the results of these simulations are presented. The implementation of this gridless technique is presented and its benefits are briefly outlined. In parallel with the development of a continuous-wave atom laser, tools suited to manipulate cold atomic beams in atom guides have been explored. An atomic guide with a tunable aspect ratio, using rf-dressed state potentials, is presented.