The Josephson frequency conversion in the millimeter and submillimeter wave region is studied with superconducting Nb–Nb point-contact junctions at 4.2 °K, using the contact both as the local oscillator and the mixer with intermediate frequencies of 0.1, 0.3, and 9.2 GHz. The point contact is in a nonresonant structure and fed by a constant current source: neither a strong rf coupling of the contact with a cavity nor a stabilizing shunt resistance was proved necessary. The direct observation of frequency conversion was performed with a microwave receiver at 9.2 GHz in a range of Josephson frequencies between 145 and 1600 GHz. The experiments with intermediate frequencies fi of 0.1 and 0.3 GHz indicate that conventional frequency conversion does not occur but that the observed signals are related to noise effects. An analysis of the frequency conversion mechanism in a Josephson junction operated as an oscillator-mixer is proposed which includes the noise effects and also the feedback effects induced in a junction driven by a constant current source. The results show that low-frequency current components are induced in the junction, which can give large spurious signals when small i.f. are used.
The Josephson frequency conversion in the millimeter and submillimeter wave region is studied with superconducting Nb–Nb point-contact junctions at 4.2 °K, using the contact both as the local oscillator and the mixer with intermediate frequencies of 0.1, 0.3, and 9.2 GHz. The point contact is in a nonresonant structure and fed by a constant current source: neither a strong rf coupling of the contact with a cavity nor a stabilizing shunt resistance was proved necessary. The direct observation of frequency conversion was performed with a microwave receiver at 9.2 GHz in a range of Josephson frequencies between 145 and 1600 GHz. The experiments with intermediate frequencies fi of 0.1 and 0.3 GHz indicate that conventional frequency conversion does not occur but that the observed signals are related to noise effects. An analysis of the frequency conversion mechanism in a Josephson junction operated as an oscillator-mixer is proposed which includes the noise effects and also the feedback effects induced in a junction driven by a constant current source. The results show that low-frequency current components are induced in the junction, which can give large spurious signals when small i.f. are used.
The Josephson frequency conversion in the millimeter and submillimeter wave region is studied with superconducting Nb-Nb point contact junctions at 4.2 K, using the contact both as the local oscillator and the mixer with intermediate frequencies of 0.1 and 9.2 GHz. Frequency conversion signals are only detected in the latter case with a microwave receiver at 9.2 GHz in a range of Josephson frequencies between 145 and 1 600 GHz. The experiments with intermediate frequency fi of 0.1 GHz indicate for this small value of f i that the observed signals are not related to frequency conversion but noise effects. An analysis of the frequency conversion mechanism in a Josephson junction operated as an oscillator-mixer is proposed which includes the noise effects and also the feedback effects induced in a junction driven by a constant current source. We have then investigated the noise properties up to 450 GHz of superconducting point-contacts using the junction as an oscillator-mixer where the Josephson current is mixed with harmonics of an externally applied signal. The emitted intermediate frequency is detected at 9.2 GHz and its linewidth is measured. In the very high frequency range the dc quasiparticle current dominates in a Josephson weak-link and we compare the corresponding theoretical linewidth calculated by Scalapino with our experimental results.
Microwave superconducting mixers operating at 10–13 GHz utilizing Josephson junctions have been investigated analytically and experimentally. Measurements on mixer sensitivity were carried out at 13 GHz using waveguide-mounted experimental point-contact Josephson junctions at 4.2 K. Results showed sensitivities of −90 dBm/MHz (10−18 W/Hz) which included mismatch losses encountered in the waveguide structure. The Josephson junction mixing mechanism was analyzed on the basis of small-signal modulation of the staircase like dc I-V characteristics. It was shown that a small-signal microwave excitation results in an ac lateral shift of the regions between steps, such that: (a) Optimum Josephson mixing occurs halfway between steps. (b) Mixing occurs between all steps with maximum conversion efficiency between the zero and first step. (c) Predicted low conversion loss and possibly internal gain for a matched mixer. The analytical model was simulated by a digital computer and the behavior of the Josephson mixer predicted for various conditions of excitation. The model chosen for the analysis and the computer simulation is based on the simplest assumptions concerning bulk-formed Josephson junctions. In the laboratory an external local oscillator set 60 MHz below the signal frequency was used to induce the well-known step structure in the dc I-V characteristic of the point-contact Josephson junction. Mixing of the Lo and signal was found to occur between constant voltage steps in agreement with both analysis and computer simulation. The correctness of the model is demonstrated by the agreement between the theory and experiment.
Abstract : The term 'Josephson effects' refers to a number of unusual properties of current flow through a barrier or weak link between two superconductors. Such a structure--called a Josephson junction--gives rise to frequency conversion effects that suggest its use as an oscillator-mixer in the millimeter and submillimeter region. Such a device would offer high sensitivity, broad bandwidth, tunability, and, in certain modes of operation, the possibility of conversion gain. These frequency conversion effects were observed in the range of 100 GHz to 600 GHz and beyond. The junctions were driven by a 75 GHz or 25 GHz klystron while coupled either to a coaxial cavity resonant at 20 GHz or to a resonance at about 500 GHz associated with the junction structure. Lines in the junction voltage-current characteristic were observed which demonstrated that, at certain values of junction bias, power at the rf--or its harmonics--was converted to power at the resonance frequency. An explanation of the experiment is given together with the necessary background, which provides the basis for a discussion of such operational considerations as upper frequency limit, sensitivity, temperature of operation, and saturation behavior at high signal levels. (Author)
The properties of point-contact Josephson junctions operated as mixers with an external local oscillator at 130 GHz have been studied, and the results compared with predictions of the resistively shunted junction model. It was found that the junction’s output noise could be within a factor of 1.5 of the model prediction based on the thermal-driving noise. When the coupling to the rf source was optimized, a factor of 2 discrepancy was typical. The measured conversion efficiency agreed with the model, within the experimental uncertainty in the equivalent microwave circuit. The best coupling was achieved in full-height waveguide. The best overall performance, measured using the hot/cold source technique, was a single sideband conversion efficiency of 0.30 and a mixer-noise temperature of 180 K (both ±20%). The best junctions were made of Nb, with carefully prepared points. Nonideal behavior in other junctions is ascribed to heating effects. There is some evidence that junctions whose resistance exceeds a threshold value of ∼60 Ω are no longer well described by the RSJ model. A discussion is given of possible improvements in performance with better junctions or improved rf matching.
NOTE: Text or symbols not renderable in plain ASCII are indicated by [...]. Abstract is included in .pdf document. This thesis describes both theoretical and experimental investigations into the dynamics and noise processes of Josephson junctions, with the intent of evaluating their potential as mixers in heterodyne instruments for submillimeter-wave (i.e., the frequency range from 300 GHz to 3THz) detection. Superconducting tunnel junctions utilizing the nonlinearity due to photon-assisted tunneling of quasiparticles (SIS mixers) have become the state-of-the-art technology for sensitive heterodyne detection up to frequencies of about 700 [...]. Recent progress in the fabrication of high [...], superconductors has led to Josephson-effect devices with [...] products of up to ten millivolts, which might be suitable for mixing at frequencies of many terahertz. The key question for weighing the prospects for high-frequency Josephson mixers is that of the sensitivity which can be attained. Previous experimental work on Josephson mixing suggests the existence of an "excess" noise, which degrades the sensitivity. Theoretical modeling of mixer performance, based on the resistivelyshunted junction (RSJ) model for the dynamics of the device, also indicates the presence of larger noise than expected. The origin of this noise was not clearly understood, however, nor was its exact magnitude or expected scaling with frequency or junction characteristics known. In addition, previous experiments utilized crude devices of the point-contact type, which were unstable and thus undesirable for real applications. In the first part of this thesis research, extensive numerical simulations were performed with the RSJ model, including calculations of mixer noise and conversion efficiency. These calculations have revealed that the source of excess noise is the AC Josephson oscillations of the device, which can be completely incoherent, with a linewidth comparable to their frequency. Thus they appear as a broadband noise source. While this noise is intrinsic and unavoidable, an optimized mixer is still shown to be capable of interesting sensitivity levels, and the excess noise is expected to become relatively less important as the operating frequency is increased. Secondly, a process has been developed for the fabrication of stable, well-characterized, and reproducible Josephson devices based on resistively-shunted Nb and NbN tunnel junctions. The devices utilize submicron-area, high current-density tunnel junctions and a AuGe shunt resistor to yield completely non-hysteretic I-V curves, normal-state resistances of about [...] products of about half a millivolt. These devices should be nearly optimal for mixing at [...]. Heterodyne measurements using these junctions have been performed in a waveguide mixer mount. Receiver temperatures as low as 190 K (DSB), with -6 dB conversion efficiency, have been obtained at 100 [...], but these results are still a factor of about four higher than those predicted by the RSJ simulations. Accurate measurements of the available noise power of the junctions at the intermediate frequency of 1.5 [...] were made, and confirmed that the receivers were limited by elevated junction output noise. The deviations of the noise from theoretical predictions are shown to be caused by the nonlinear interaction of the junction with the embedding circuit. While this work points out some of the complexity introduced by the strong nonlinearity of Josephson devices, it is still expected that Josephson-effect mixers may be useful for heterodyne detection at very high frequencies.
Fundamental mixing at 36 GHz in non-hysteretic Nb point contacts has been observed with overall conversion efficiencies in the range 0.33 ≤ η ≤ 4 and mixer noise temperatures in the neighborhood of TM ~ 200 K. The observed conversion efficiencies are in good agreement with the Resistively Shunted Junction model. The observed noise can be accounted for by assuming that the Johnson noise in the shunt resistor is the only source of noise driving the junction. Somewhat larger noise is seen from resonantly coupled mixers than is seen when the mixer is driven from an rf current source. Fundamental mixing in hysteretic junctions is limited to a narrow if bandwidth and gives much larger conversion gain but also larger noise. Parametric amplification at the if frequency is seen in hysteretic junctions. Fourth order harmonic mixing with ωLO/2 π at 9 GHz has been achieved with performance almost comparable to fundamental mixing. Cavity mode mixing appears less promising.