Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Microwave and superconducting techniques for measurements on unconventional Josephson junctions

Georgina M. Klemencic

Published Jul 1, 2013• 1 citation
OpenAlex

Abstract

The frst part of the thesis describes the instrumentation, testing and analysis of a planar circuit designed for the measurement of the current-phase relationship of niobium-cobalt-insulator-niobium Josephson junctions. A detailed analysis method and fitting routine was developed but the results show that an irreducible mutual inductance places a limit on the accuracy of the chip for the intended measurement. The second part describes a study of the magnetic and microwave properties of a range of thin film niobium coplanar resonators with cobalt and normal metal layers. Magnetic measurements show a magnetic dead layer of 1.3 nm. The observed microwave losses are found to be two orders of magnitude higher than for high quality niobium films. Computer simulation shows that this is mainly due to conductive, rather than magnetic losses, and is in good agreement with the observed proportionality to cobalt thickness. Measurements of the temperature and magnetic field dependence of the losses and resonant frequency as a function of the cobalt thickness show no signs of the oscillatory thickness dependence reported in a number of other experiments. The temperature dependence of all films is found to be in good agreement with Mattis-Bardeen theory.

Related papers

Josephson Junctions: Oscillators and Broadband Spectrometers at Frequencies up to 1 THz

J. Edstam

This thesis is devoted to some selected applications of the Josephson junction oscillator. The initial work was performed using low-Tc Nb/PbBi tunnel junctions, while the later parts were done using the recently developed high-Tc YBa2Cu3O7 (YBCO) Josephson junctions. The latter junctions have raised the hope for Josephson oscillator applications with substantially increased operation frequencies and temperatures. In the first part of this thesis the use of inductor-resistor (LR) shunted tunnel junctions in arrays of phase locked Josephson junction oscillators was investigated. The LR shunt is designed to resonate out the intrinsic tunnel junction capacitance at the operation frequency. We show that LR shunted tunnel junctions have important advantages compared to the commonly used resistively shunted tunnel junctions; i.e. narrower linewidths, higher impedance of the junctions and that they can be optimized also at frequencies higher than about 100 GHz. Design rules for stable, non-chaotic oscillations with optimized output power were developed. Measurements on a non- optimized circuit show that oscillator arrays of LR shunted tunnel junctions can generate substantial power, ~10 nW to a 300 .OMEGA. load at 390 GHz from a 10 junction array. In the second part the phase locking of YBCO Josephson junctions was clearly demonstrated for the first time. Mutual phase locking of two junctions was observed at frequencies between 0.2 and 1 THz, and was only limited by the bandwidth of the coupling circuit. The locking was in good agreement with simulations based on the resistively shunted junction model. The interaction of a single Josephson junction with a 5 junction oscillator array was also measured at frequencies up to about 350 GHz, but was substantially reduced by the high losses of the coupling circuit. The YBCO Josephson junctions were found to be interesting candidates for microwave generation at frequencies approaching 1 THz and oscillator arrays to be mainly limited by the high losses of the coupling circuits at these frequencies. In the third part the interaction of YBCO Josephson junctions with integrated resonators were studied for the first time. Using a novel method, Josephson Broadband Spectroscopy (JOBS), the high frequency properties of the resonators were measured with a bandwidth of up to 1 THz and in the temperature range 4-77 K. The YBCO surface resistance (9 m.OMEGA. at 4 K and 100 GHz) was found to scale as f2 and had a temperature dependence in good agreement with the two-fluid model, modified with 18% non-pairing charge carriers. The YBCO London penetration depth was frequency independent (460 nm at 4 K) and had a temperature dependence in agreement with the two-fluid model.

•Jan 1, 1994•0 citations

Josephson junctions in superconducting coplanar DC bias cavities: Fundamental studies and applications

Felix E. Schmidt

This thesis investigates fundamental properties of Josephson junctions embedded in microwave circuits, and an application arising from this hybrid approach. We used the versatility of superconducting coplanar DC bias cavities to extract previously inaccessible information on phase coherent and subgap mechanisms of graphene Josephson junctions. Chapter 1 gives an introduction to the technology of Josephson field effect transistors, among which graphene junctions show promise for future improvements in quantum computation. Together with an overview of the Josephson effect in superconducting-semiconducting systems, we introduce the concept of coplanar DC bias cavities for probing Josephson junctions at gigahertz frequencies. In chapter 2, we describe the experimental methods developed for carrying out the subsequent measurements. We include details on fabrication, material properties and measurement setup. Results of graphene Josephson junctions embedded in DC bias microwave resonators are presented in chapters 3 and 4. By following the resonance frequency and losses of the circuit, we are able to extract the junctions’ Josephson inductance and subgap resistance. Studying the nonlinear power and bias current response reveals further information on the underlying loss mechanisms and current phase relation. We turn to an application of our hybrid bias cavity – Josephson junction devices to detect small, low-frequency currents in chapter 5. Our device is competitive with state-of-the-art techniques for microwave radiation detection and, with minor modifications, should be able to outperform existing technologies by orders of magnitude. Finally, we conclude the presented work in chapter 6 and provide an outlook on potential future research.

•Jul 28, 2020•0 citations

Loss mechanisms in superconducting thin film microwave resonators

Jan Goetz, Frank Deppe, Max Haeberlein +10 more

We present a systematic analysis of the internal losses of superconducting coplanar waveguide microwave resonators based on niobium thin films on silicon substrates. In particular, we investigate losses introduced by Nb/Al interfaces in the center conductor, which is important for experiments where Al based Josephson junctions are integrated into Nb based circuits. We find that these interfaces can be a strong source for two-level state (TLS) losses, when the interfaces are not positioned at current nodes of the resonator. In addition to TLS losses, for resonators including Al, quasiparticle losses become relevant above 200 mK. Finally, we investigate how losses generated by eddy currents in conductive material on the backside of the substrate can be minimized by using thick enough substrates or metals with high conductivity on the substrate backside.

arXiv:1510.05957•Journal of Applied Physics•Jan 5, 2016•69 citations

Fabrication and Characterization of Superconductive Coplanar Waveguide Resonators

Adem Ergül

The objective of this thesis is to evaluate a generic process for fabrication and characterization of the Superconductive coplanar waveguide (CPW) resonators. Superconductive CPW resonators with various lengths and shapes are designed to investigate their electrical and magnetic properties as well as resonance properties and sensitivities. In the first part of thesis, two different models are introduced in order to estimate the nonlinear kinetic inductance of a superconducting CPW resonator. The first model is based on Bean critical-state model and the second one is based on current dependence of London penetration depth. The existence of a shift in resonant frequency of Superconductive CPW resonator caused by a non-linear kinetic inductance is also shown experimentally. Simulations were carried out to estimate the nonlinear kinetic inductance due to the self- induced magnetic field penetration. The rest of the thesis is concerned with development of very smooth Aluminum (Al) thin films with RMS (Root Mean Square) roughness 1~nm and CAD (Computer Aid Design) of superconductive CPW resonators. Experimental investigation of a generic fabrication technique for superconductive CPW resonator is carried out. Many resonators are fabricated with different design parameters, such as centerline or gap width, film thickness and gap capacitors length. The fabrication process is described in detail. Electron Beam Lithography is used to fabricate Nb and Al CPW resonators which are coupled to outer conductors via gap capacitors. We have fabricated GHz frequency CPW resonators with quality factors, Q up 5X10^5.

•Jan 1, 2009•0 citations

Microwave Properties of Superconducting Atomic-Layer Deposited TiN Films

P. C. J. J. Coumou, Marc R. Zuiddam, E. F. C. Driessen +3 more

We have grown superconducting TiN films by atomic layer deposition with thicknesses ranging from 6 to 89 nm. This deposition method allows us to tune the resistivity and critical temperature by controlling the film thickness. The microwave properties are measured, using a coplanar-waveguide resonator, and we find internal quality factors above a million, high sheet inductances (5.2-620 pH), and pulse response times up to 100 μs. The high normal state resistivity of the films (>; 100 μΩ · cm) affects the superconducting state and thereby the electrodynamic response. The microwave response is modeled using a quasiparticle density of states modified with an effective pair-breaker, consistently describing the measured temperature dependence of the quality factor and the resonant frequency.

arXiv:1212.4434•IEEE Transactions on Applied Superconductivity•Dec 27, 2012•40 citations

TiN 및 Al 박막의 초전도 길이 척도에 대한 정량적 특성 분석 및 양자 소자 응용으로의 고찰

김성훈

Although advances in circuit design and quantum control have improved the coherence of superconducting quantum circuits, microwave losses arising from the intrinsic properties of constituent materials remain a primary limitation. Identifying and understanding these decoherence mechanisms requires research at the material level, which in turn requires the development of precise measurement techniques and quantitative analysis of superconducting thin films. This thesis introduces an experimental framework for characterizing basic superconducting length scales, specifically the superconducting coherence length and the London penetration depth. The superconductivity of titanium nitride (TiN) thin films was investigated using upper critical field measurements. Analysis of the pronounced anisotropy between the in-plane and out-of-plane critical fields, along with the observed temperature-dependent dimensional crossover, indicates that superconductivity is confined to an effective thickness that is even smaller than the nominal value. These results provide quantitative evidence for the presence of an interfacial dead layer in which the superconductivity is strongly suppressed. Furthermore, this transport-based analysis suggests that it can serve as a non-destructive method for evaluating interface quality and effective superconducting volume in disordered systems. To measure the London penetration depth, a key parameter for characterizing and exploring superconductivity, the electrodynamic response of superconducting films was examined using the two-coil mutual inductance technique (TCMI). Aluminum thin films served as a standard system to validate both the experimental setup and the numerical inversion code. The measured temperature dependence of the penetration depth aligns with conventional s-wave BCS theory, yielding a zero-temperature penetration depth λ(0) of 45 nm, consistent with well-known bulk values. These methodologies enable high-throughput characterization, which is essential for optimizing superconducting films for quantum circuits. Moreover, this capability allows a systematic separation of geometry-dependent circuit effects from intrinsic material-loss mechanisms. This distinction provides a practical pathway toward improving coherence by addressing material limitations at their origin.

•Jan 1, 2026•0 citations
The frst part of the thesis describes the instrumentation, testing and analysis of a planar circuit designed for the measurement of the current-phase relationship of niobium-cobalt-insulator-niobium Josephson junctions. A detailed analysis method and fitting routine was developed but the results show that an irreducible mutual inductance places a limit on the accuracy of the chip for the intended measurement. The second part describes a study of the magnetic and microwave properties of a range of thin film niobium coplanar resonators with cobalt and normal metal layers. Magnetic measurements show a magnetic dead layer of 1.3 nm. The observed microwave losses are found to be two orders of magnitude higher than for high quality niobium films. Computer simulation shows that this is mainly due to conductive, rather than magnetic losses, and is in good agreement with the observed proportionality to cobalt thickness. Measurements of the temperature and magnetic field dependence of the losses and resonant frequency as a function of the cobalt thickness show no signs of the oscillatory thickness dependence reported in a number of other experiments. The temperature dependence of all films is found to be in good agreement with Mattis-Bardeen theory.
This thesis is devoted to some selected applications of the Josephson junction oscillator. The initial work was performed using low-Tc Nb/PbBi tunnel junctions, while the later parts were done using the recently developed high-Tc YBa2Cu3O7 (YBCO) Josephson junctions. The latter junctions have raised the hope for Josephson oscillator applications with substantially increased operation frequencies and temperatures. In the first part of this thesis the use of inductor-resistor (LR) shunted tunnel junctions in arrays of phase locked Josephson junction oscillators was investigated. The LR shunt is designed to resonate out the intrinsic tunnel junction capacitance at the operation frequency. We show that LR shunted tunnel junctions have important advantages compared to the commonly used resistively shunted tunnel junctions; i.e. narrower linewidths, higher impedance of the junctions and that they can be optimized also at frequencies higher than about 100 GHz. Design rules for stable, non-chaotic oscillations with optimized output power were developed. Measurements on a non- optimized circuit show that oscillator arrays of LR shunted tunnel junctions can generate substantial power, ~10 nW to a 300 .OMEGA. load at 390 GHz from a 10 junction array. In the second part the phase locking of YBCO Josephson junctions was clearly demonstrated for the first time. Mutual phase locking of two junctions was observed at frequencies between 0.2 and 1 THz, and was only limited by the bandwidth of the coupling circuit. The locking was in good agreement with simulations based on the resistively shunted junction model. The interaction of a single Josephson junction with a 5 junction oscillator array was also measured at frequencies up to about 350 GHz, but was substantially reduced by the high losses of the coupling circuit. The YBCO Josephson junctions were found to be interesting candidates for microwave generation at frequencies approaching 1 THz and oscillator arrays to be mainly limited by the high losses of the coupling circuits at these frequencies. In the third part the interaction of YBCO Josephson junctions with integrated resonators were studied for the first time. Using a novel method, Josephson Broadband Spectroscopy (JOBS), the high frequency properties of the resonators were measured with a bandwidth of up to 1 THz and in the temperature range 4-77 K. The YBCO surface resistance (9 m.OMEGA. at 4 K and 100 GHz) was found to scale as f2 and had a temperature dependence in good agreement with the two-fluid model, modified with 18% non-pairing charge carriers. The YBCO London penetration depth was frequency independent (460 nm at 4 K) and had a temperature dependence in agreement with the two-fluid model.
This thesis investigates fundamental properties of Josephson junctions embedded in microwave circuits, and an application arising from this hybrid approach. We used the versatility of superconducting coplanar DC bias cavities to extract previously inaccessible information on phase coherent and subgap mechanisms of graphene Josephson junctions. Chapter 1 gives an introduction to the technology of Josephson field effect transistors, among which graphene junctions show promise for future improvements in quantum computation. Together with an overview of the Josephson effect in superconducting-semiconducting systems, we introduce the concept of coplanar DC bias cavities for probing Josephson junctions at gigahertz frequencies. In chapter 2, we describe the experimental methods developed for carrying out the subsequent measurements. We include details on fabrication, material properties and measurement setup. Results of graphene Josephson junctions embedded in DC bias microwave resonators are presented in chapters 3 and 4. By following the resonance frequency and losses of the circuit, we are able to extract the junctions’ Josephson inductance and subgap resistance. Studying the nonlinear power and bias current response reveals further information on the underlying loss mechanisms and current phase relation. We turn to an application of our hybrid bias cavity – Josephson junction devices to detect small, low-frequency currents in chapter 5. Our device is competitive with state-of-the-art techniques for microwave radiation detection and, with minor modifications, should be able to outperform existing technologies by orders of magnitude. Finally, we conclude the presented work in chapter 6 and provide an outlook on potential future research.
We present a systematic analysis of the internal losses of superconducting coplanar waveguide microwave resonators based on niobium thin films on silicon substrates. In particular, we investigate losses introduced by Nb/Al interfaces in the center conductor, which is important for experiments where Al based Josephson junctions are integrated into Nb based circuits. We find that these interfaces can be a strong source for two-level state (TLS) losses, when the interfaces are not positioned at current nodes of the resonator. In addition to TLS losses, for resonators including Al, quasiparticle losses become relevant above 200 mK. Finally, we investigate how losses generated by eddy currents in conductive material on the backside of the substrate can be minimized by using thick enough substrates or metals with high conductivity on the substrate backside.
The objective of this thesis is to evaluate a generic process for fabrication and characterization of the Superconductive coplanar waveguide (CPW) resonators. Superconductive CPW resonators with various lengths and shapes are designed to investigate their electrical and magnetic properties as well as resonance properties and sensitivities. In the first part of thesis, two different models are introduced in order to estimate the nonlinear kinetic inductance of a superconducting CPW resonator. The first model is based on Bean critical-state model and the second one is based on current dependence of London penetration depth. The existence of a shift in resonant frequency of Superconductive CPW resonator caused by a non-linear kinetic inductance is also shown experimentally. Simulations were carried out to estimate the nonlinear kinetic inductance due to the self- induced magnetic field penetration. The rest of the thesis is concerned with development of very smooth Aluminum (Al) thin films with RMS (Root Mean Square) roughness 1~nm and CAD (Computer Aid Design) of superconductive CPW resonators. Experimental investigation of a generic fabrication technique for superconductive CPW resonator is carried out. Many resonators are fabricated with different design parameters, such as centerline or gap width, film thickness and gap capacitors length. The fabrication process is described in detail. Electron Beam Lithography is used to fabricate Nb and Al CPW resonators which are coupled to outer conductors via gap capacitors. We have fabricated GHz frequency CPW resonators with quality factors, Q up 5X10^5.
We have grown superconducting TiN films by atomic layer deposition with thicknesses ranging from 6 to 89 nm. This deposition method allows us to tune the resistivity and critical temperature by controlling the film thickness. The microwave properties are measured, using a coplanar-waveguide resonator, and we find internal quality factors above a million, high sheet inductances (5.2-620 pH), and pulse response times up to 100 μs. The high normal state resistivity of the films (>; 100 μΩ · cm) affects the superconducting state and thereby the electrodynamic response. The microwave response is modeled using a quasiparticle density of states modified with an effective pair-breaker, consistently describing the measured temperature dependence of the quality factor and the resonant frequency.
Although advances in circuit design and quantum control have improved the coherence of superconducting quantum circuits, microwave losses arising from the intrinsic properties of constituent materials remain a primary limitation. Identifying and understanding these decoherence mechanisms requires research at the material level, which in turn requires the development of precise measurement techniques and quantitative analysis of superconducting thin films. This thesis introduces an experimental framework for characterizing basic superconducting length scales, specifically the superconducting coherence length and the London penetration depth. The superconductivity of titanium nitride (TiN) thin films was investigated using upper critical field measurements. Analysis of the pronounced anisotropy between the in-plane and out-of-plane critical fields, along with the observed temperature-dependent dimensional crossover, indicates that superconductivity is confined to an effective thickness that is even smaller than the nominal value. These results provide quantitative evidence for the presence of an interfacial dead layer in which the superconductivity is strongly suppressed. Furthermore, this transport-based analysis suggests that it can serve as a non-destructive method for evaluating interface quality and effective superconducting volume in disordered systems. To measure the London penetration depth, a key parameter for characterizing and exploring superconductivity, the electrodynamic response of superconducting films was examined using the two-coil mutual inductance technique (TCMI). Aluminum thin films served as a standard system to validate both the experimental setup and the numerical inversion code. The measured temperature dependence of the penetration depth aligns with conventional s-wave BCS theory, yielding a zero-temperature penetration depth λ(0) of 45 nm, consistent with well-known bulk values. These methodologies enable high-throughput characterization, which is essential for optimizing superconducting films for quantum circuits. Moreover, this capability allows a systematic separation of geometry-dependent circuit effects from intrinsic material-loss mechanisms. This distinction provides a practical pathway toward improving coherence by addressing material limitations at their origin.