Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2609.23126

Performance optimization of cascaded traveling wave Josephson parametric amplifiers

Ilari Lilja, Ekaterina Mukhanova, Stanislav Khaldeev, Ilya Golokolenov, Visa Vesterinen, Pertti Hakonen

quant-phcond-mat.supr-conSubmitted Sep 19, 2026• Announced Sep 22, 2026• 0 citations
arXivHTMLPDF

Abstract

Traveling-wave parametric amplifiers (TWPAs) based on Josephson metamaterials provide broadband gain with near-quantum-limited added noise. Whereas long nonlinear metamaterial devices can deliver high gain, short arrays suffer less from dissipation, pump depletion, and internal standing waves which can degrade noise performance. Here, we demonstrate a cascaded TWPA architecture that combines the advantages of both approaches by employing a short (736-element), low-dissipation Superconducting Nonlinear Asymmetric Inductive eLement (SNAIL)-based TWPA as the first amplification stage, followed by a conventional long (1632-element) TWPA that provides additional gain. The resulting amplifier cascade achieves nearly 30 dB of total gain over a tunable bandwidth of approximately 1 GHz while maintaining added noise close to the quantum limit. Our results establish a cascade of TWPAs as a practical approach for high-gain, broadband, quantum amplification with applications in quantum information processing, multi-mode entanglement, and quantum sensing applications at microwave frequencies.

Comments
16 pages, 3 figures

Related papers

Josephson traveling-wave parametric amplifier with inverse Kerr phase matching

M. T. Bell

Superconducting traveling-wave parametric amplifiers (TWPA) have emerged as highly versatile devices, offering broadband amplification with quantum-limited noise performance. They hold significant potential for addressing the readout bottleneck in prototype quantum computers, enabling scalability. Key challenges with this technology include achieving sufficient gain with minimal gain ripple while maintaining low noise performance. Efficient phase matching between a weak signal and a strong pump over the entire length of the TWPA is critical to overcoming these challenges. We present an experimental demonstration of the inverse Kerr phase matching technique in a TWPA, first proposed in Ref. Phys. Rev. Appl. 4, 024014. This method addresses several limitations of conventional dispersion engineering approaches of phase matching in the four-wave mixing parametric process in TWPAs. Most notably the existence of an unusable region of gain near the pump frequency which typically corresponds to the region of most optimal phase matching and maximum gain. The inverse Kerr phase matching approach, allows for greater frequency separation between the region of optimal gain and pump, \textit{in situ} tunability of the pump, minimal gain ripple, and a compact footprint which reduces losses. A TWPA employing the inverse Kerr phase matching technique experimentally demonstrated 20 dB of gain over a 3 GHz instantaneous bandwidth, with a tunable bandwidth of 8 GHz, minimal gain ripple, and near quantum-limited noise performance, with 1.5 photons of added noise.

arXiv:2507.17039•Physical Review Applied•Dec 23, 2025•1 citation

Development of Quantum Limited Superconducting Amplifiers for Advanced Detection

S. Pagano, C. Barone, M. Borghesi +36 more

Ultralow-noise microwave amplification and detection play a central role in different applications, going from fundamental physics experiments to the deployment of quantum technologies. In many applications the necessity of reading multiple detectors, or cavities or qubits, calls for large bandwidth amplifiers with the lowest possible noise. Current technologies are based on High Electron Mobility Transistors and Josephson Parametric Amplifiers. Both have limitations, the former in terms of the minimum noise, the latter in terms of bandwidth. Superconducting Traveling Wave Parametric Amplifiers (TWPAs) have the potential of offering quantum limited noise and large bandwidth. These amplifiers are based on the parametric amplification of microwaves traveling along a transmission line with embedded nonlinear elements. We are developing superconducting TWPAs based both on Josephson junction arrays (Traveling Wave Josephson Parametric Amplifiers) and on nonlinear kinetic inductance (Dispersion Engineered Traveling Wave Kinetic Inductance Amplifiers). Our goal is to achieve large bandwidth (in the 5 to 10 GHz range), large gain (more than 20 dB), large saturation power (more than −50 dBm), and near quantum limited noise (noise temperature less than 600 mK). Current achievements in the design and development of the high performance TWPAs are here reported and discussed, together with current limitations and possible future developments.

IEEE Transactions on Applied Superconductivity•Jan 25, 2022•16 citations

Broadband Parametric Amplification in DARTWARS

M. Faverzani, P Campana, Rodolfo Carobene +46 more

Abstract Superconducting parametric amplifiers offer the capability to amplify feeble signals with extremely low levels of added noise, potentially reaching quantum-limited amplification. This characteristic makes them essential components in the realm of high-fidelity quantum computing and serves to propel advancements in the field of quantum sensing. In particular, Traveling-Wave Parametric Amplifiers (TWPAs) may be especially suitable for practical applications due to their multi-Gigahertz amplification bandwidth, a feature lacking in Josephson Parametric Amplifiers (JPAs), despite the latter being a more established technology. This paper presents recent developments of the DARTWARS (Detector Array Readout with Traveling Wave AmplifieRS) project, focusing on the latest prototypes of Kinetic Inductance TWPAs (KITWPAs). The project aims to develop a KITWPA capable of achieving 20 dB of amplification. To enhance the production yield, the first prototypes were fabricated with half the length and expected gain of the final device. In this paper, we present the results of the characterization of one of the half-length prototypes. The measurements revealed an average amplification of approximately 9 dB across a 2 GHz bandwidth for a KITWPA spanning 17 mm in length.

arXiv:2402.12045•Journal of Low Temperature Physics•May 3, 2024•5 citations

A Black-Box Quantum Model for Superconducting Traveling-Wave Parametric Amplifiers

Michael Haider

Superconducting quantum computing is at the forefront of demonstrating quantum advantages for revolutionary applications in science and technology. One key component for the readout of qubit state information is given by superconducting traveling-wave parametric amplifiers (TWPAs) due to their low power dissipation and unprecedented quantum-limited noise performance. This work presents a black-box circuit quantum electrodynamic model for TWPAs with arbitrary superconducting nonlinear elements. A unified Hamiltonian description for directly pumped and flux-driven amplifiers is derived, and analytic results for the gain and the added quantum noise are presented, closely matching recent experimental realizations. We also offer an optimization strategy for nonlinear elements for large gain and low noise based on the proposed black-box quantum model. The results of this article will be helpful in the design and multitarget optimization of new and improved quantum-limited low-noise amplifiers.

IEEE Transactions on Microwave Theory and Techniques•Jan 9, 2024•13 citations

Three-wave mixing traveling-wave parametric amplifier with periodic variation of the circuit parameters

Anita Fadavi Roudsari, Daryoush Shiri, Hampus Renberg Nilsson +8 more

We report on the implementation of a near-quantum-limited, traveling-wave parametric amplifier that uses three-wave mixing (3WM). To favor amplification by 3WM, we use superconducting nonlinear asymmetric inductive element (SNAIL) loops, biased with a dc magnetic flux. In addition, we equip the device with dispersion engineering features to create a stopband at the second harmonic of the pump and suppress the propagation of the higher harmonics that otherwise degrade the amplification. With a chain of 440 SNAILs, the amplifier provides up to 20 dB gain and a 3-dB bandwidth of 1 GHz. The added noise by the amplifier is found to be less than one photon.

arXiv:2209.07551•Applied Physics Letters•Jan 30, 2023•33 citations

Development of superconducting josephson junction travelling wave parametric amplifiers

Navarro Montilla, Javier

Recent progress in physics has increased the necessity for ultra-low noise amplifiers capable of operating at the quantum limit performance. These amplifiers are essential to enhance astronomical detection, dark-matter search, and qubit readout in quantum computing, among other applications. Superconducting Josephson junction Travelling Wave Parametric Amplifiers (JTWPAs) operated in the microwave range, have demonstrated high gain over several gigahertz (GHz) bandwidth, with quantum-limited noise performance and minimal heat dissipation. These excellent properties make JTWPAs an ideal solution for ultra-low noise amplification. This thesis delves into the design, fabrication and characterisation of JTWPAs operated in the microwave (1-16 GHz) and the W-band (70-115GHz) regimes. A generalised coupled-mode equations (CME) framework describing JTWPAs based on Josephson junctions and DC superconducting quantum interference devices (SQUIDs) is introduced. This framework can be combined with electromagnetic (EM) simulation softwares to model the JTWPAs, facilitating their design. It is therefore used to model two microwave JTWPA designs, using parallel plate capacitors (PPCs) and interdigitated capacitors (IDCs). The fabrication and characterisation of both designs are presented, and possible fabrication and design issues are carefully discussed. Despite these issues, we observed broadband gain in the JTWPA with PPCs, achieving > 20 dB gain at several frequency points, and a measured P1dB = −95.8dBm when operated at 17.3 dB. The RF properties of a 500-junction Josephson array are also presented in this manuscript. The device creates a Fabry-Perot cavity, leading to non-travelling wave parametric effects, such as narrow-band gain. We also observed indications of efficient phase-sensitive amplification. The thesis is concluded with the first — to the best of our knowledge — experimental attempt to extend the operational frequency of a JTWPA to the W-band. The novel design, fabrication techniques and characterisation of the W-band JTWPA are discussed in detail in this manuscript, leading to promising results suggesting that JTWPA could operate at high frequencies.

•Jan 1, 2024•0 citations
Traveling-wave parametric amplifiers (TWPAs) based on Josephson metamaterials provide broadband gain with near-quantum-limited added noise. Whereas long nonlinear metamaterial devices can deliver high gain, short arrays suffer less from dissipation, pump depletion, and internal standing waves which can degrade noise performance. Here, we demonstrate a cascaded TWPA architecture that combines the advantages of both approaches by employing a short (736-element), low-dissipation Superconducting Nonlinear Asymmetric Inductive eLement (SNAIL)-based TWPA as the first amplification stage, followed by a conventional long (1632-element) TWPA that provides additional gain. The resulting amplifier cascade achieves nearly 30 dB of total gain over a tunable bandwidth of approximately 1 GHz while maintaining added noise close to the quantum limit. Our results establish a cascade of TWPAs as a practical approach for high-gain, broadband, quantum amplification with applications in quantum information processing, multi-mode entanglement, and quantum sensing applications at microwave frequencies.
Superconducting traveling-wave parametric amplifiers (TWPA) have emerged as highly versatile devices, offering broadband amplification with quantum-limited noise performance. They hold significant potential for addressing the readout bottleneck in prototype quantum computers, enabling scalability. Key challenges with this technology include achieving sufficient gain with minimal gain ripple while maintaining low noise performance. Efficient phase matching between a weak signal and a strong pump over the entire length of the TWPA is critical to overcoming these challenges. We present an experimental demonstration of the inverse Kerr phase matching technique in a TWPA, first proposed in Ref. Phys. Rev. Appl. 4, 024014. This method addresses several limitations of conventional dispersion engineering approaches of phase matching in the four-wave mixing parametric process in TWPAs. Most notably the existence of an unusable region of gain near the pump frequency which typically corresponds to the region of most optimal phase matching and maximum gain. The inverse Kerr phase matching approach, allows for greater frequency separation between the region of optimal gain and pump, \textit{in situ} tunability of the pump, minimal gain ripple, and a compact footprint which reduces losses. A TWPA employing the inverse Kerr phase matching technique experimentally demonstrated 20 dB of gain over a 3 GHz instantaneous bandwidth, with a tunable bandwidth of 8 GHz, minimal gain ripple, and near quantum-limited noise performance, with 1.5 photons of added noise.
Ultralow-noise microwave amplification and detection play a central role in different applications, going from fundamental physics experiments to the deployment of quantum technologies. In many applications the necessity of reading multiple detectors, or cavities or qubits, calls for large bandwidth amplifiers with the lowest possible noise. Current technologies are based on High Electron Mobility Transistors and Josephson Parametric Amplifiers. Both have limitations, the former in terms of the minimum noise, the latter in terms of bandwidth. Superconducting Traveling Wave Parametric Amplifiers (TWPAs) have the potential of offering quantum limited noise and large bandwidth. These amplifiers are based on the parametric amplification of microwaves traveling along a transmission line with embedded nonlinear elements. We are developing superconducting TWPAs based both on Josephson junction arrays (Traveling Wave Josephson Parametric Amplifiers) and on nonlinear kinetic inductance (Dispersion Engineered Traveling Wave Kinetic Inductance Amplifiers). Our goal is to achieve large bandwidth (in the 5 to 10 GHz range), large gain (more than 20 dB), large saturation power (more than −50 dBm), and near quantum limited noise (noise temperature less than 600 mK). Current achievements in the design and development of the high performance TWPAs are here reported and discussed, together with current limitations and possible future developments.
Abstract Superconducting parametric amplifiers offer the capability to amplify feeble signals with extremely low levels of added noise, potentially reaching quantum-limited amplification. This characteristic makes them essential components in the realm of high-fidelity quantum computing and serves to propel advancements in the field of quantum sensing. In particular, Traveling-Wave Parametric Amplifiers (TWPAs) may be especially suitable for practical applications due to their multi-Gigahertz amplification bandwidth, a feature lacking in Josephson Parametric Amplifiers (JPAs), despite the latter being a more established technology. This paper presents recent developments of the DARTWARS (Detector Array Readout with Traveling Wave AmplifieRS) project, focusing on the latest prototypes of Kinetic Inductance TWPAs (KITWPAs). The project aims to develop a KITWPA capable of achieving 20 dB of amplification. To enhance the production yield, the first prototypes were fabricated with half the length and expected gain of the final device. In this paper, we present the results of the characterization of one of the half-length prototypes. The measurements revealed an average amplification of approximately 9 dB across a 2 GHz bandwidth for a KITWPA spanning 17 mm in length.
Superconducting quantum computing is at the forefront of demonstrating quantum advantages for revolutionary applications in science and technology. One key component for the readout of qubit state information is given by superconducting traveling-wave parametric amplifiers (TWPAs) due to their low power dissipation and unprecedented quantum-limited noise performance. This work presents a black-box circuit quantum electrodynamic model for TWPAs with arbitrary superconducting nonlinear elements. A unified Hamiltonian description for directly pumped and flux-driven amplifiers is derived, and analytic results for the gain and the added quantum noise are presented, closely matching recent experimental realizations. We also offer an optimization strategy for nonlinear elements for large gain and low noise based on the proposed black-box quantum model. The results of this article will be helpful in the design and multitarget optimization of new and improved quantum-limited low-noise amplifiers.
We report on the implementation of a near-quantum-limited, traveling-wave parametric amplifier that uses three-wave mixing (3WM). To favor amplification by 3WM, we use superconducting nonlinear asymmetric inductive element (SNAIL) loops, biased with a dc magnetic flux. In addition, we equip the device with dispersion engineering features to create a stopband at the second harmonic of the pump and suppress the propagation of the higher harmonics that otherwise degrade the amplification. With a chain of 440 SNAILs, the amplifier provides up to 20 dB gain and a 3-dB bandwidth of 1 GHz. The added noise by the amplifier is found to be less than one photon.
Recent progress in physics has increased the necessity for ultra-low noise amplifiers capable of operating at the quantum limit performance. These amplifiers are essential to enhance astronomical detection, dark-matter search, and qubit readout in quantum computing, among other applications. Superconducting Josephson junction Travelling Wave Parametric Amplifiers (JTWPAs) operated in the microwave range, have demonstrated high gain over several gigahertz (GHz) bandwidth, with quantum-limited noise performance and minimal heat dissipation. These excellent properties make JTWPAs an ideal solution for ultra-low noise amplification. This thesis delves into the design, fabrication and characterisation of JTWPAs operated in the microwave (1-16 GHz) and the W-band (70-115GHz) regimes. A generalised coupled-mode equations (CME) framework describing JTWPAs based on Josephson junctions and DC superconducting quantum interference devices (SQUIDs) is introduced. This framework can be combined with electromagnetic (EM) simulation softwares to model the JTWPAs, facilitating their design. It is therefore used to model two microwave JTWPA designs, using parallel plate capacitors (PPCs) and interdigitated capacitors (IDCs). The fabrication and characterisation of both designs are presented, and possible fabrication and design issues are carefully discussed. Despite these issues, we observed broadband gain in the JTWPA with PPCs, achieving > 20 dB gain at several frequency points, and a measured P1dB = −95.8dBm when operated at 17.3 dB. The RF properties of a 500-junction Josephson array are also presented in this manuscript. The device creates a Fabry-Perot cavity, leading to non-travelling wave parametric effects, such as narrow-band gain. We also observed indications of efficient phase-sensitive amplification. The thesis is concluded with the first — to the best of our knowledge — experimental attempt to extend the operational frequency of a JTWPA to the W-band. The novel design, fabrication techniques and characterisation of the W-band JTWPA are discussed in detail in this manuscript, leading to promising results suggesting that JTWPA could operate at high frequencies.