Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2609.10606

When Measurement Constraints Favor Quantum Computational Sensing for Stealthy Power-Grid Attack Detection

Saisubramaniam Gopalakrishnan, Supreeth B S, Pranav Sarda, Ashesh Xalxo, Dagnachew Birru

On Aqora:Gopalakrishnan SaisubramaniamGopalakrishnan Saisubramaniam
quant-phcs.CRSubmitted Sep 8, 2026• Announced Sep 9, 2026• 0 citations
arXivHTMLPDF

Abstract

Power-grid defenses that rely on digital telemetry remain vulnerable to stealthy attacks that preserve plausible reported states while altering the underlying physical system. We study when Nitrogen-Vacancy (NV) sensing provides a useful independent physical channel, and when coherent processing before measurement adds value. Across IEEE 14-, 30-, and 118-bus simulations with Lindblad NV models, we evaluate standard FDIA, BDD-stealth, statistical-stealth, and concealed topology attacks. The results reveal an observability hierarchy: evidence shifts from digital telemetry, to reported-versus-physical consistency, to the physical NV state. Quantum Computational Sensing (QCS) follows this selectivity, becoming informative only when the physical state itself carries attack evidence. We then compare QCS, conventional 4-setting NV readout, and tomography under matched measurement budgets. At a matched total budget of only 40 physical trials per sensor on case14, QCS reaches AP $0.944$, versus 0.800 for conventional NV readout and 0.751 for tomography; the same low-budget ordering holds on case30 and case118. Multi-setting methods recover as additional measurements become affordable, showing that the QCS benefit is a measurement-efficiency advantage rather than a universal accuracy advantage. Finally, we ask where the benefit varies across the three case simulations. Although the quantum-to-classical Fisher-information ratio increases from 1.21x to 1.54x, Normal--Attack Helstrom separation collapses in the harder regimes, and interleaved control substantially increases that separation only on case14, thereby quantum sensitivity does not necessarily imply task-relevant distinguishability. Our results show that realized QCS utility depends on the full chain from physical perturbation to state separation, coherent processing, and measurement under the resource constraints of the task.

Related papers

Receiver-Limited Fisher Information for Quantum Sensors under Realistic Readout

Juan Sumaya-Martinez, Omar Olmos-López, Cristian Adán Mojica Casique +1 more

Abstract Quantum Fisher information quantifies the sensitivity encoded in a parameter-dependent quantum state, whereas the performance of a practical sensor is limited by the information that survives the physical channel and can be extracted by the available receiver. We introduce an accessible Fisher-information framework based on a physically admissible family of measurements and use it to separate state-level sensitivity, channel degradation, and receiver limitations. The framework is applied to Ramsey and NOON interferometry, squeezed-state displacement sensing, two-level thermometry, and multiparameter qubit sensing. We show that resource normalization, finite visibility, readout errors, measurement rank, shot allocation, calibration uncertainty, and nuisance parameters can substantially modify the experimentally available advantage. For squeezed-state sensing, homodyne-axis misalignment produces a finite optimal squeezing, while bounded calibration uncertainty leads to a robust operating rule. In the pure-loss model considered here, attenuation reduces the attainable information without shifting this optimum. The results provide practical design rules that connect quantum-enhanced state preparation with realistic measurement constraints and experimentally extractable sensing performance.

•Oct 26, 2026•0 citations

Quantum computational displacement sensing

Sridhar Prabhu, Saeed A. Khan, Xingrui Song +7 more

Quantum computational sensing (QCS) combines quantum sensing with quantum computing to extract task-relevant information from the physical world. QCS can in principle achieve an accuracy advantage for specific tasks versus the alternative of raw-signal estimation using conventional quantum sensing followed by task-specific classical postprocessing. Here we report the experimental demonstration of quantum computational displacement sensing (QCDS) with a superconducting circuit comprising a qubit coupled to an oscillator. We consider binary classification sensing tasks, where the goal is to predict the class label of a single complex-valued displacement sensed once by the oscillator. Rather than estimating the displacement, our computational-sensing protocol -- using parameterized quantum circuits before and after sensing -- attempts to determine the binary class label using quantum processing and map it onto the ground or excited state of the qubit. A single measurement of the qubit directly outputs the prediction. We implemented circuits with up to 24 entangling gates and 38 free parameters, which were trained in silico. We show that increasing the circuit depth systematically improves expressivity and classification accuracy. We experimentally obtained an accuracy advantage over a suite of protocols that first use conventional quantum sensing to estimate the displacement before using classical postprocessing to perform prediction. For certain tasks, our protocol achieves a 15-percentage-points higher classification accuracy than most conventional approaches considered. Our results establish the feasibility of quantum computational sensing with noisy superconducting hardware and illustrate how integrating quantum computation with quantum sensing can enhance performance when the goal is to estimate a property or function of a signal rather than to estimate the signal.

quant-pharXiv:2604.13177•Apr 16, 2026•6 citations

QML for Quantum Sensing under Measurement-Induced Information Loss

Sounak Bhowmik, Himanshu Thapliyal

Nitrogen-vacancy (NV) centers in diamond can serve as highly sensitive solid-state quantum sensors for high-sensitivity magnetometry. However, in the noisy intermediate-scale quantum (NISQ) era, extracting reliable information from noisy, finite-shot, and measurement-limited sensing data remains a considerable challenge. Whereas, quantum machine learning (QML) offers a potential path to improve parameter estimation by learning nonlinear relationships between quantum-sensing data and the underlying physical signal. In this work, we investigate the role of QML in magnetic-field estimation within an NV center-inspired magnetometry setting. We formulated magnetic field sensing as a supervised regression task. We compared the performance of several classical machine learning models trained on measurement-based classical data with that of quantum kernel-based models trained on pre-measurement coherent quantum states. Our objective is to isolate the impact of measurement-induced information loss and therefore provide a theoretical upper bound on the sensing performance. The upper bound is achievable only when coherent quantum information is directly available to the learning model. Our results show that QML-based sensing performance improves significantly with coherent quantum-state information, and not much with changes in model complexity or learning paradigm. This observation underscores the importance of learning pipelines that tightly integrate quantum sensors and QML models to enhance magnetic field sensing under realistic constraints.

quant-pharXiv:2608.23934•Aug 26, 2026•0 citations

Quantum computational sensing using quantum signal processing, quantum neural networks, and Hamiltonian engineering

Saeed A. Khan, Sridhar Prabhu, Logan G. Wright +1 more

Abstract Combining quantum sensing with quantum computing can lead to quantum computational sensing (QCS) protocols that are able to more efficiently extract task-specific information from physical signals than is possible otherwise. In this paper, we present, in theory and numerical simulations, the application of two quantum algorithms—quantum signal processing and quantum neural networks—to various binary and multiclass machine-learning classification tasks in sensing. Here, sensing operations are interleaved with computing operations, giving rise to nonlinear functions of the sensed signals. Our approach to optimizing QCS protocols takes into account quantum sampling noise and allows us to engineer protocols that can yield accurate results with as few as just a single measurement shot. In all cases, we have been able to show a regime of operation where a quantum computational sensor can achieve higher accuracy than a conventional quantum sensor for a given budget of sensing time, with a simulated accuracy advantage of >20 percentage points for some tasks. We also present protocols for performing nonlinear tasks using Hamiltonian-engineered bosonic systems and quantum signal processing with hybrid qubit-bosonic systems, and empirically show an advantage when the received signal has a limited mean photon number.

arXiv:2507.15845•npj Quantum Information•May 14, 2026•7 citations

Quantum Sensing of Non-Repeatable Events Enhanced by In-Sensor Quantum Reservoir Computing

Daiki Sasaki, Hideaki Kawaguchi, Yuichiro Matsuzaki

High-density nitrogen-vacancy (NV) ensembles in diamond enable sensitive magnetometry. Many quantum-sensing protocols rely on reproducible target fields, allowing repeated measurements under different sensing conditions. In dynamical decoupling (DD) magnetometry, sweeping the interval between $π$ pulses across repeated measurements enables estimation of the frequency and amplitude of an unknown alternating field. For non-repeatable events, however, the same field waveform cannot be reproduced for measurements under different settings. Here we propose NV-based in-sensor quantum reservoir computing (NV-QRC) for sensing such events. Field-driven many-body dynamics and simultaneous fluorescence readout from multiple spatial regions provide a classical classifier with multiple features from a single event. For binary phase classification, we benchmark NV-QRC against DD magnetometry using a single pulse sequence fixed in advance. We show that NV-QRC can retain class-dependent information in regimes where the fixed-DD protocol fails to capture it. These results identify non-repeatable-event sensing as a promising application of quantum reservoir computing.

quant-pharXiv:2609.06292•Sep 8, 2026•0 citations

Quantum Current Detection and State Monitoring Technology for Power Grid Energy Storage Batteries Based on NV Centers

Teng Tian, Long Zhao, Rujia Chou +3 more

Accurate current detection and state-of-charge (SoC) estimation are critical for the safe and efficient operation of grid-scale energy storage systems. This paper proposes a quantum sensing approach based on nitrogen-vacancy (NV) centers in diamond for non-contact current measurement and battery state monitoring. The method utilizes optically detected magnetic resonance (ODMR) to measure magnetic fields induced by battery currents and employs a dual-sensor gradiometer configuration to suppress environmental noise. Experimental results demonstrate a magnetic sensitivity of $8.5{\text{pT}}/\sqrt {{\text{Hz}}} $ and accurate current measurement over a wide dynamic range from 0.01 A to 1000 A with a linearity error below 0.15% (measured at 25°C ambient temperature with 10 s averaging time). The proposed approach also improves SoC estimation, achieving a mean absolute error of 1.07% over 500 cycles (tested on a 100 Ah LiFePO4battery at 0.5C charge/discharge rate, 25°C±2°C) and outperforming conventional coulomb counting methods. In addition, the system enables simultaneous multi-parameter monitoring, enhancing battery diagnostic capability. These results indicate that NV-based quantum sensing provides a promising solution for next-generation battery management systems.

IEEE International Conference on Electrical Power Systems and Intelligent Control (EPSIC)•May 22, 2026•0 citations
Power-grid defenses that rely on digital telemetry remain vulnerable to stealthy attacks that preserve plausible reported states while altering the underlying physical system. We study when Nitrogen-Vacancy (NV) sensing provides a useful independent physical channel, and when coherent processing before measurement adds value. Across IEEE 14-, 30-, and 118-bus simulations with Lindblad NV models, we evaluate standard FDIA, BDD-stealth, statistical-stealth, and concealed topology attacks. The results reveal an observability hierarchy: evidence shifts from digital telemetry, to reported-versus-physical consistency, to the physical NV state. Quantum Computational Sensing (QCS) follows this selectivity, becoming informative only when the physical state itself carries attack evidence. We then compare QCS, conventional 4-setting NV readout, and tomography under matched measurement budgets. At a matched total budget of only 40 physical trials per sensor on case14, QCS reaches AP 0.9440.9440.944, versus 0.800 for conventional NV readout and 0.751 for tomography; the same low-budget ordering holds on case30 and case118. Multi-setting methods recover as additional measurements become affordable, showing that the QCS benefit is a measurement-efficiency advantage rather than a universal accuracy advantage. Finally, we ask where the benefit varies across the three case simulations. Although the quantum-to-classical Fisher-information ratio increases from 1.21x to 1.54x, Normal--Attack Helstrom separation collapses in the harder regimes, and interleaved control substantially increases that separation only on case14, thereby quantum sensitivity does not necessarily imply task-relevant distinguishability. Our results show that realized QCS utility depends on the full chain from physical perturbation to state separation, coherent processing, and measurement under the resource constraints of the task.
Abstract Quantum Fisher information quantifies the sensitivity encoded in a parameter-dependent quantum state, whereas the performance of a practical sensor is limited by the information that survives the physical channel and can be extracted by the available receiver. We introduce an accessible Fisher-information framework based on a physically admissible family of measurements and use it to separate state-level sensitivity, channel degradation, and receiver limitations. The framework is applied to Ramsey and NOON interferometry, squeezed-state displacement sensing, two-level thermometry, and multiparameter qubit sensing. We show that resource normalization, finite visibility, readout errors, measurement rank, shot allocation, calibration uncertainty, and nuisance parameters can substantially modify the experimentally available advantage. For squeezed-state sensing, homodyne-axis misalignment produces a finite optimal squeezing, while bounded calibration uncertainty leads to a robust operating rule. In the pure-loss model considered here, attenuation reduces the attainable information without shifting this optimum. The results provide practical design rules that connect quantum-enhanced state preparation with realistic measurement constraints and experimentally extractable sensing performance.
Quantum computational sensing (QCS) combines quantum sensing with quantum computing to extract task-relevant information from the physical world. QCS can in principle achieve an accuracy advantage for specific tasks versus the alternative of raw-signal estimation using conventional quantum sensing followed by task-specific classical postprocessing. Here we report the experimental demonstration of quantum computational displacement sensing (QCDS) with a superconducting circuit comprising a qubit coupled to an oscillator. We consider binary classification sensing tasks, where the goal is to predict the class label of a single complex-valued displacement sensed once by the oscillator. Rather than estimating the displacement, our computational-sensing protocol -- using parameterized quantum circuits before and after sensing -- attempts to determine the binary class label using quantum processing and map it onto the ground or excited state of the qubit. A single measurement of the qubit directly outputs the prediction. We implemented circuits with up to 24 entangling gates and 38 free parameters, which were trained in silico. We show that increasing the circuit depth systematically improves expressivity and classification accuracy. We experimentally obtained an accuracy advantage over a suite of protocols that first use conventional quantum sensing to estimate the displacement before using classical postprocessing to perform prediction. For certain tasks, our protocol achieves a 15-percentage-points higher classification accuracy than most conventional approaches considered. Our results establish the feasibility of quantum computational sensing with noisy superconducting hardware and illustrate how integrating quantum computation with quantum sensing can enhance performance when the goal is to estimate a property or function of a signal rather than to estimate the signal.
Nitrogen-vacancy (NV) centers in diamond can serve as highly sensitive solid-state quantum sensors for high-sensitivity magnetometry. However, in the noisy intermediate-scale quantum (NISQ) era, extracting reliable information from noisy, finite-shot, and measurement-limited sensing data remains a considerable challenge. Whereas, quantum machine learning (QML) offers a potential path to improve parameter estimation by learning nonlinear relationships between quantum-sensing data and the underlying physical signal. In this work, we investigate the role of QML in magnetic-field estimation within an NV center-inspired magnetometry setting. We formulated magnetic field sensing as a supervised regression task. We compared the performance of several classical machine learning models trained on measurement-based classical data with that of quantum kernel-based models trained on pre-measurement coherent quantum states. Our objective is to isolate the impact of measurement-induced information loss and therefore provide a theoretical upper bound on the sensing performance. The upper bound is achievable only when coherent quantum information is directly available to the learning model. Our results show that QML-based sensing performance improves significantly with coherent quantum-state information, and not much with changes in model complexity or learning paradigm. This observation underscores the importance of learning pipelines that tightly integrate quantum sensors and QML models to enhance magnetic field sensing under realistic constraints.
Abstract Combining quantum sensing with quantum computing can lead to quantum computational sensing (QCS) protocols that are able to more efficiently extract task-specific information from physical signals than is possible otherwise. In this paper, we present, in theory and numerical simulations, the application of two quantum algorithms—quantum signal processing and quantum neural networks—to various binary and multiclass machine-learning classification tasks in sensing. Here, sensing operations are interleaved with computing operations, giving rise to nonlinear functions of the sensed signals. Our approach to optimizing QCS protocols takes into account quantum sampling noise and allows us to engineer protocols that can yield accurate results with as few as just a single measurement shot. In all cases, we have been able to show a regime of operation where a quantum computational sensor can achieve higher accuracy than a conventional quantum sensor for a given budget of sensing time, with a simulated accuracy advantage of >20 percentage points for some tasks. We also present protocols for performing nonlinear tasks using Hamiltonian-engineered bosonic systems and quantum signal processing with hybrid qubit-bosonic systems, and empirically show an advantage when the received signal has a limited mean photon number.
High-density nitrogen-vacancy (NV) ensembles in diamond enable sensitive magnetometry. Many quantum-sensing protocols rely on reproducible target fields, allowing repeated measurements under different sensing conditions. In dynamical decoupling (DD) magnetometry, sweeping the interval between πππ pulses across repeated measurements enables estimation of the frequency and amplitude of an unknown alternating field. For non-repeatable events, however, the same field waveform cannot be reproduced for measurements under different settings. Here we propose NV-based in-sensor quantum reservoir computing (NV-QRC) for sensing such events. Field-driven many-body dynamics and simultaneous fluorescence readout from multiple spatial regions provide a classical classifier with multiple features from a single event. For binary phase classification, we benchmark NV-QRC against DD magnetometry using a single pulse sequence fixed in advance. We show that NV-QRC can retain class-dependent information in regimes where the fixed-DD protocol fails to capture it. These results identify non-repeatable-event sensing as a promising application of quantum reservoir computing.
Accurate current detection and state-of-charge (SoC) estimation are critical for the safe and efficient operation of grid-scale energy storage systems. This paper proposes a quantum sensing approach based on nitrogen-vacancy (NV) centers in diamond for non-contact current measurement and battery state monitoring. The method utilizes optically detected magnetic resonance (ODMR) to measure magnetic fields induced by battery currents and employs a dual-sensor gradiometer configuration to suppress environmental noise. Experimental results demonstrate a magnetic sensitivity of $8.5{\text{pT}}/\sqrt {{\text{Hz}}} $ and accurate current measurement over a wide dynamic range from 0.01 A to 1000 A with a linearity error below 0.15% (measured at 25°C ambient temperature with 10 s averaging time). The proposed approach also improves SoC estimation, achieving a mean absolute error of 1.07% over 500 cycles (tested on a 100 Ah LiFePO4battery at 0.5C charge/discharge rate, 25°C±2°C) and outperforming conventional coulomb counting methods. In addition, the system enables simultaneous multi-parameter monitoring, enhancing battery diagnostic capability. These results indicate that NV-based quantum sensing provides a promising solution for next-generation battery management systems.