Monolithic three-dimensional (3D) Paul traps combine the high-precision microfabrication of two-dimensional (2D) chip traps with the deep trapping potentials and low heating rates characteristic of macroscopic 3D Paul traps, which are typically machined by traditional means and mechanically assembled. However, achieving low motional heating rates and optical access with a high numerical aperture (NA) while maintaining the high radio-frequency (RF) voltages required for trapping heavy ionic species, such as Yb
+ and Ba
+, remains a significant technical challenge. In this work, we present a fused-silica, monolithic segmented 3D Paul trap with an ion-electrode distance of 250
μm, and stable operation at high RF voltages. We benchmark the performance of the trap using Yb
+ ions, demonstrating axially homogeneous trapping potentials spanning over 200
μm about the axial center of the trap, high multi-directional optical access (up to 0.7 NA), and radial motional heating as low as $\dot{\bar n}=1.1 \pm 0.1 $ quanta/s at radial trap frequencies about 3 MHz near room temperature. Furthermore, we observe a motional Ramsey coherence time,
T2, of about 95 ms for the radial center-of-mass mode. We demonstrate the generation of a two-qubit Bell state with a parity contrast of
99.3−1.5+0.7% with state preparation and measurement correction. These results establish fused-silica monolithic 3D Paul traps as a scalable, modular platform for quantum simulation, computation, metrology, and networking with heavy ionic species.
We report a 3D-printed microwave-resonator Paul trap that operates at the GHz frequencies required for electron confinement while preserving an open geometry suitable for laser access and imaging ion Coulomb crystals. The resonator exhibits moderate quality factors of approximately 1000, enabling large confining electric-field amplitudes at low input power, and is in good agreement with finite-element-method (FEM) predictions despite manufacturing imperfections, which we experimentally characterize. The validated FEM model is then used to calculate the electromagnetic fields in the trapping region. These field distributions, together with surface-roughness measurements, are incorporated into a model of electron spin-qubit decoherence to estimate the coherence time. Our analysis predicts that electron spin-qubit coherence times on the order of 10 ms should be achievable under the assumption that motional heating is dominated by Johnson noise, making such systems relevant for quantum information processing. The method of obtaining the coherence time is applicable to any electron Paul trap.
Monolithic three-dimensional (3D) Paul traps combine the high-precision microfabrication of two-dimensional (2D) chip traps with the deep trapping potentials and low heating rates characteristic of macroscopic 3D Paul traps, which are typically machined by traditional means and mechanically assembled. However, achieving low motional heating rates and optical access with a high numerical aperture (NA) while maintaining the high radio-frequency (rf) voltages required for trapping heavy ionic species, such as Yb + and Ba + , remains a significant technical challenge. In this work, we present a fused silica, monolithic segmented 3D Paul trap with an ion-electrode distance of 250 μ m , and stable operation at high rf voltages. We benchmark the trap’s performance using Yb + ions, demonstrating axially homogeneous trapping potentials spanning over 200 μ m about the trap’s axial center, high multidirectional optical access (up to 0.7 NA), and radial motional heating as low as n ¯ ˙ = 1.1 ± 0.1 quanta / s at radial trap frequencies about 3 MHz near room temperature. Furthermore, we observe a motional Ramsey coherence time, T 2 , of about 96 ms for the radial center-of-mass mode. We demonstrate the generation of a two-qubit Bell state with a parity contrast of 99.3 − 1.5 + 0.7 % with state preparation and measurement correction. These results establish fused-silica monolithic 3D Paul traps as a scalable, modular platform for quantum simulation, computation, metrology, and networking with heavy ionic species.
Linear radio-frequency quadrupole (RFQ) traps are crucial for ion and phase-space manipulation across diverse physics platforms, including quantum information processing, precision atomic spectroscopy, and high-resolution mass or laser spectrometry. We present the design, electrostatic field optimization, and performance characterization of a scalable, multi-layer printed circuit board (PCB) linear RFQ trap. By utilizing a PCB-based "stacked-electrode" geometry to generate high-quality quadrupolar fields, this architecture suppresses higher-order multipole field components by up to an order of magnitude compared to planar "flat surface-electrode" designs and allows for reclaiming up to 60% of the radial pseudopotential-well depth of an ideal hyperbolic quadrupole. Following a thorough optimisation and characterization using both simulations and experiments, we demonstrate its suitability as a cooler buncher, showing rapid helium buffer-gas cooling with time constants between 34 +/- 3 us and 412 +/- 23 us, and achieving a highly compressed longitudinal phase-space emittance of only 58 +/- 4 eV*ns. The low beam emittance provides flexible control of the extracted bunch properties: weak extraction fields yield energy spreads down to 2.5 +/- 0.4 eV, whereas strong fields produce ultra-narrow temporal widths down to 2.6 +/- 0.3 ns. The results establish our PCB-RFQ platform as a versatile, scalable, and cost-effective alternative to traditionally machined rod-based RFQ assemblies for advanced ion-trapping, beam-preparation, or quantum applications.
Trapped-ion applications, such as in quantum information, precision measurements, optical clocks, and mass spectrometry, rely on specialized high-performance ion traps. The latter applications typically employ traditional machining to customize macroscopic 3D Paul traps, while quantum information processing experiments usually rely on photo-lithographic techniques to miniaturize the traps and meet scalability requirements. Using photolithography, however, it is challenging to fabricate the complex three-dimensional electrode structures required for optimal confinement. Here we address these limitations by adopting a high-resolution 3D printing technology based on two-photon polymerization supporting fabrication of large arrays of high-performance miniaturized 3D traps. We show that 3D-printed ion traps combine the advantages of traditionally machined 3D traps with the miniaturization provided by photolithography by confining single calcium ions in a small 3D-printed ion trap with radial trap frequencies ranging from 2 MHz to 24 MHz. The tight confinement eases ion cooling requirements and allows us to demonstrate high-fidelity coherent operations on an optical qubit after only Doppler cooling. With 3D printing technology, the design freedom is drastically expanded without sacrificing scalability and precision so that ion trap geometries can be optimized for higher performance and better functionality.