Traveling-Wave Parametric Amplifiers (TWPAs) are ubiquitous in superconducting circuit readout, providing high gain with near-quantum-limited noise performance across a wide bandwidth. Their operation, however, relies on a strong microwave pump tone that is typically delivered using off-chip passive components, such as directional couplers or diplexers. These external elements add loss, increase system complexity, and limit scalability. Here, we present a traveling-wave parametric amplifier that incorporates on-chip input and output diplexers for pump routing. This co-fabricated architecture offers a compact and scalable solution for superconducting-circuit readout.
Traveling-Wave Parametric Amplifiers (TWPAs) are ubiquitous in superconducting circuit readout, providing high gain with near-quantum-limited noise performance across a wide bandwidth. Their operation, however, relies on a strong microwave pump tone that is typically delivered using off-chip passive components, such as directional couplers or diplexers. These external elements add loss, increase system complexity, and limit scalability. Here, we present a traveling-wave parametric amplifier that incorporates on-chip input and output diplexers for pump routing. This co-fabricated architecture offers a compact and scalable solution for superconducting-circuit readout.
Quantum computing systems and fundamental physics experiments using superconducting technologies frequently require signal amplification chains operating near the quantum limit of added noise. Both Josephson parametric amplifiers (JPAs) and traveling wave parametric amplifiers (TWPAs) have been used as first-stage amplifiers to enable readout chains operating within a few quanta or less of the quantum limit. These devices are also presently entering the commercial industry. However, nearly all demonstrations and existing products require bulky external microwave components for interconnection and application of requisite biases. These components – cabling interconnects, bias tees, directional couplers, and diplexers – increase the overall amplifier footprint, installation complexity, and reduce already limited available cryogenic volumes. Additionally, these components introduce loss and reflections which impact the measurement efficiency and readout system noise performance; thus making it more difficult to operate near the quantum limit. Here we present the design and validation of microfabricated bias tees and directional couplers for operating three-wave mixing kinetic inductance TWPAs (KITs). We report the performance of KITs integrated with the microfabricated rf components. Using these devices we demonstrate reduction in the amplifier installation footprint by a factor of nearly five and elimination of all external, lossy microwave components previously required to operate a KIT. Our device displays a 2.8 GHz 3 dB bandwidth with a median true gain of 17.5 dB and median system noise of 3.4 quanta. These efforts represent the first full integration of all rf components mandatory for TWPA operation on-chip. Our results mark significant progress towards the miniaturization and simplification of parametric amplifier setups and will aid in their more widespread applicability.
High-fidelity qubit measurement is a critical element of all quantum computing architectures. In superconducting systems, qubits are typically measured by probing a readout resonator with a weak microwave tone that must be amplified before reaching the room temperature electronics. Superconducting parametric amplifiers have been widely adopted as the first amplifier in the chain, primarily because of their low noise performance, approaching the quantum limit. However, they require isolators and circulators to route signals up the measurement chain and to protect qubits from amplified noise. While these commercial components are wideband and simple to use, their intrinsic loss, size, and magnetic shielding requirements impact overall measurement efficiency and scalability. Here we report a parametric amplifier that achieves both broadband forward amplification and backward isolation in a single, compact, non-magnetic circuit that could be integrated on chip with superconducting qubits. The approach relies on a nonlinear transmission line that supports traveling-wave parametric amplification of forward propagating signals, and isolation via frequency conversion of backward propagating signals. This traveling-wave parametric amplifier and converter has the potential to reduce the readout hardware overhead when scaling up the size of superconducting quantum computers.
Superconducting travelling-wave parametric amplifiers (TWPAs) provide broadband gain, low added noise, and high dynamic range, making them attractive for applications requiring wide instantaneous bandwidth. This is crucial for amplifying multiplexed narrow band signals spread over a wide frequency range, such as qubit resonator arrays, or amplifying inherently wide band signals, such as in spectrometers or radiometers. In many cases, however, the useful bandwidth of a TWPA is limited by the production of the idler tone at an image frequency. For three-wave-mixing (3WM) TWPAs, for example, an input signal at fs is indistinguishable from one at fp−fs, which can produce spectral ambiguity when the input spectrum is broadband or not known in advance. We experimentally demonstrate a balanced architecture that doubles the instantaneous image-rejected bandwidth available to a 3WM TWPA by spatially separating the amplified signal from the output pump and generated idler, which resolves the sideband degeneracy. The architecture consists of two amplifiers connected between a pair of 180∘ hybrid couplers, with the signal and pump injected and output through the sum and difference ports, respectively. Using two kinetic-inductance TWPAs, we demonstrate approximately 20 dB of signal gain across nearly an octave of bandwidth, together with pump rejection below --20 dB and an average image rejection of approximately --15 dB over the operating band. These results establish balanced TWPAs as a practical approach to broadband parametric amplification, enabling improved contamination free bandwidth and eliminating the need for complex filtering.
Traveling-wave parametric amplifiers (TWPAs) have attracted much attention for their broadband amplification and near-quantum-limited noise performance. TWPAs are nonreciprocal by nature providing gain for forward-propagating signals and transmission line losses for backward traveling waves. This intrinsic nonreciprocity is insufficient to protect sensitive quantum devices from backaction due to noise from warmer amplification stages in practical systems, and requires the use of bulky cryogenic isolators. We present a multistage TWPA (mTWPA) that addresses this limitation by achieving passive in-band reverse isolation alongside near-quantum-limited noise performance. The multistage architecture consists of two mode conversion stages and a reflectionless high-pass filter that provides the passive isolation. Experimental measurements of a prototype mTWPA demonstrated 20 dB of forward gain across a 1.6 GHz bandwidth and greater than 35 dB of reverse isolation. Noise measurements indicate performance at 1.7 times the quantum limit. This demonstrates that the increased complexity of a multistage TWPA design does not lead to significant added noise. The designed distribution of gain across the stages is engineered to minimize internal amplifier noise at the input, and we propose further optimization strategies in redistribution of the gain between the stages. This level of isolation mitigates noise from warmer amplification stages, matching the performance of conventional isolators. The passive reverse isolation of the mTWPA, allows for the amplifier to operate in pulsed mode where the amplifier is off during qubit gate operations and is turned on during readout allowing for an isolator free scalable readout architecture.
We investigate the peripheral circuits required to enable ideal performance for a high-gain traveling-wave parametric amplifier (TWPA) based on three-wave mixing . By embedding the TWPA in a network of superconducting diplexers, hybrid couplers, and impedance matching networks, the amplifier can deliver a high stable gain with near-quantum-limited noise performance, with suppressed gain ripples, while eliminating the reflections of the signal, the idler and the pump as well as the transmission of all unwanted tones. We also demonstrate a configuration where the amplifier can isolate. We call this technique (WIF). The theory is supported by simulations that predict over 20 dB gain in the 4–8 GHz band with 10 dB isolation for a single amplifier and 30 dB isolation for two cascaded amplifiers. We demonstrate how the WIF-TWPAs can be used to construct controllable isolators with over 40 dB isolation over the full 4–8 GHz band. Finally, we look at nonidealities and show how certain nonidealities can be devastating for both the gain and the idler filtering, especially a cutoff imbalance or a flux imbalance, and discuss how to compensate for them. Published by the American Physical Society 2024
Superconducting traveling-wave parametric amplifiers (TWPA) have emerged as highly versatile devices, offering broadband amplification with quantum-limited noise performance. They hold significant potential for addressing the readout bottleneck in prototype quantum computers, enabling scalability. Key challenges with this technology include achieving sufficient gain with minimal gain ripple while maintaining low noise performance. Efficient phase matching between a weak signal and a strong pump over the entire length of the TWPA is critical to overcoming these challenges. We present an experimental demonstration of the inverse Kerr phase matching technique in a TWPA, first proposed in Ref. Phys. Rev. Appl. 4, 024014. This method addresses several limitations of conventional dispersion engineering approaches of phase matching in the four-wave mixing parametric process in TWPAs. Most notably the existence of an unusable region of gain near the pump frequency which typically corresponds to the region of most optimal phase matching and maximum gain. The inverse Kerr phase matching approach, allows for greater frequency separation between the region of optimal gain and pump, \textit{in situ} tunability of the pump, minimal gain ripple, and a compact footprint which reduces losses. A TWPA employing the inverse Kerr phase matching technique experimentally demonstrated 20 dB of gain over a 3 GHz instantaneous bandwidth, with a tunable bandwidth of 8 GHz, minimal gain ripple, and near quantum-limited noise performance, with 1.5 photons of added noise.