Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2508.06636 · PRX Quantum

Nondegenerate Josephson Mixers with Enhanced Bandwidth and Saturation Power for Quantum Signal Amplification and Transduction

Baleegh Abdo, Dongbing Shao, Shayne Cairns, Jae-Woong Nah, Oblesh Jinka, Srikanth J. Srinivasan, Thomas McConkey, Vincent Arena, Corrado Mancini

Published Apr 22, 2026• 0 citations
arXivHTMLPDF

Abstract

Nondegenerate Josephson mixers (JMs), formed by coupling two different transmission-line resonators to Josephson ring modulators (JRMs), are vital and versatile devices capable of processing microwave signals at the quantum limit. Owing to the lossless nondegenerate three-wave mixing process enabled by the JRM, JMs can perform phase-preserving amplification of quantum signals, generate two-mode squeezed states, and perform noiseless frequency conversion. However, due to their limited bandwidth and saturation power, such resonator-based JMs are generally unable to simultaneously process frequency-multiplexed signals required in large quantum processors. To overcome this longstanding dual challenge, we redesign the JRM parameters by optimizing its inductances to suppress higher order mixing products and engineer its electromagnetic environment by incorporating lumped-element coupled-mode networks between the JRM and the two distinct ports of the JM. By implementing these strategies, we measure for JMs realized with four coupled modes per port, operated in amplification (conversion), bandwidths of about 400 MHz (700 MHz) with power reflections above 10 dB (below − 10 dB) and saturation powers of about − 110 dBm at 15 dB ( − 91 dBm at − 26 dB). Similarly, we demonstrate for a low external quality factor resonant-mode JM operated in conversion, a maximum bandwidth of about 670 MHz with power reflections below − 10 dB and a maximum saturation power of about − 86 dBm at − 17 dB. Such nondegenerate JMs with enhanced bandwidths and saturation powers could serve in a variety of frequency-multiplexed settings ranging from high-fidelity qubit readout and unidirectional routing of quantum signals to the generation of remote entanglement with continuous variables.

DOI
10.1103/s1s8-r7y2

Related papers

A compact design for the Josephson mixer: The lumped element circuit

Jean-Damien Pillet, Emmanuel Flurin, F. Mallet +1 more

We present a compact and efficient design in terms of gain, bandwidth, and dynamical range for the Josephson mixer, the superconducting circuit performing three-wave mixing at microwave frequencies. In an all lumped-element based circuit with galvanically coupled ports, we demonstrate nondegenerate amplification for microwave signals over a bandwidth up to 50 MHz for a power gain of 20 dB. The quantum efficiency of the mixer is shown to be about 70%, and its saturation power reaches −112 dBm.

arXiv:1503.08185•Applied Physics Letters•Jun 1, 2015•18 citations

Nondegenerate three-wave mixing with the Josephson ring modulator

Baleegh Abdo, Archana Kamal, Michel Devoret

The Josephson ring modulator (JRM) is a device, based on Josephson tunnel junctions, capable of performing nondegenerate mixing in the microwave regime without losses. The generic scattering matrix of the device is calculated by solving coupled quantum Langevin equations. Its form shows that the device can achieve quantum-limited noise performance both as an amplifier and a mixer. Fundamental limitations on simultaneous optimization of performance metrics like gain, bandwidth, and dynamic range (including the effect of pump depletion) are discussed. We also present three possible integrations of the JRM as the active medium in a different electromagnetic environment. The resulting circuits, named Josephson parametric converters (JPC), are discussed in detail, and experimental data on their dynamic range are found to be in good agreement with theoretical predictions. We also discuss future prospects and requisite optimization of JPC as a preamplifier for qubit readout applications.

arXiv:1208.3142•Physical Review B•Jan 16, 2013•132 citations

Optimal design for the Josephson mixer

Jean-Damien Pillet, Emmanuel Flurin, F. Mallet +1 more

We present an optimal design in terms of gain, bandwidth and dynamical range for the Josephson mixer, the superconducting circuit performing three-wave mixing at microwave frequencies. In a compact all lumped-element based circuit with galvanically coupled ports, we demonstrate non degenerate amplification for microwave signals over a bandwidth up to 50 MHz for a power gain of 20 dB. The quantum efficiency of the mixer is shown to be about 70$\%$ and its dynamical range reaches 5 quanta per inverse dynamical bandwidth.

•Mar 27, 2015•0 citations

Creating directional quantum-limited amplification using multiple parametric drives

Tzu-Chiao Chien

One of the primary requirements for superconducting quantum information processors is high-fidelity, quantum non-demolition qubit readout. In superconducting circuits, we perform measurements with quantum-limited microwave amplifiers. These amplifiers are based on microwave cavities and powered by Josephson-junction based nonlinearities, which we drive to parametrically modulate the circuit and generate gain. However, cavity-based amplifiers generally suffer from a fixed gain-bandwidth product, a limited dynamic range, and the absence of directionality, and so they must be operated with external lossy microwave commercial components such as circulators. Many of these limitations can be circumvented by combining multiple parametric processes in a few-mode device, in particular by combining parametric drives which produce gain and those which produce gainless photon conversion. By combining balanced gain and conversion processes between a pair of modes, we have demonstrated transmission-only, phase-sensitive, gain-bandwidth-free amplification. We have also used measurements of transmon qubits with this mode of amplification to demonstrate its practical utility. More, by combining multiple instances of imbalanced gain and conversion processes among three modes, we have realized devices with non-reciprocal, transmission-only amplification, matched ports, and a large, gain-independent bandwidth. One of the biggest challenges in tuning multiple parametric processes is both inherent and dynamically-generated higher order nonlinearities in the device, which shift mode frequencies and parametric coupling strengths with pump power, preventing accurate balancing of the parametric processes. These can be controlled through engineering the Hamiltonian of the nonlinear element, in this thesis either a linearly-shunted Josephson Ring Modulator or SNAIL (Superconducting Nonlinear Asymmetric Inductive eLements), which for certain applied flux values can minimize or even change the sign of higher-order even nonlinearities. Additionally, we have explored a range of circuit parameters, allowing us to also control the relative size of odd-order nonlinearities. We have developed a series of prototypes which implement these concepts, and have achieved both high-dynamic range singly pumped amplifiers, and a promising platform for multi-parametric devices. We conclude by presenting recent progress towards implementing multiple parametric schemes that generates a practical directional amplifier, and discuss the remaining obstacles to a truly ideal parametric amplifiers.

•Sep 16, 2020•0 citations

Hybridized-Mode Parametric Amplifier in Kinetic-Inductance Circuits

Danial Davoudi, Abdul Mohamed, Shabir Barzanjeh

Parametric amplification is essential for quantum measurement, enabling the amplification of weak microwave signals with minimal added noise. While Josephson-junction-based amplifiers have become standard in superconducting quantum circuits, their magnetic sensitivity, limited saturation power, and sub-kelvin operating requirements motivate the development of alternative nonlinear platforms. Here we demonstrate a two-mode kinetic-inductance parametric amplifier based on a pair of capacitively coupled Kerr-nonlinear resonators fabricated from NbTiN and NbN thin films. The distributed Kerr nonlinearity of these materials enables nondegenerate four-wave-mixing amplification with gains approaching 40 dB, gain-bandwidth products up to 6.9 MHz, and 1-dB compression powers two to three orders of magnitude higher than those of state-of-the-art Josephson amplifiers. A coupled-mode theoretical model accurately captures the pump-induced modification of the hybridized modes and quantitatively reproduces the observed signal and idler responses. The NbN device exhibits a significantly larger Kerr coefficient and superior gain-bandwidth performance, highlighting the advantages of high-kinetic-inductance materials. Our results establish coupled kinetic-inductance resonators as a robust platform for broadband, high-power, and magnetically resilient quantum-limited amplification, offering a scalable route for advanced readout in superconducting qubits, spin ensembles, quantum dots, and other microwave-quantum technologies.

quant-pharXiv:2512.03362•Dec 4, 2025•0 citations

Optimizing Josephson-ring-modulator-based Josephson parametric amplifiers via full Hamiltonian control

Chenxu Liu, Tzu-Chiao Chien, Michael Hatridge +1 more

Josephson parametric amplifiers (JPA) are nonlinear devices that are used for quantum sensing and qubit readout in the microwave regime. While JPAs regularly operate near the quantum limit, their gain saturates for very small (few-photon) input power. In a previous work, we showed that the saturation power of JPAs is not limited by pump depletion, but instead by the fourth-order nonlinearity of Josephson junctions, the nonlinear circuit elements that enables amplification in JPAs. Here, we present a systematic study of the nonlinearities in JPAs, show which nonlinearities limit the saturation power, and present a strategy for optimizing the circuit parameters for achieving the best possible JPA. For concreteness, we focus on JPAs that are constructed around a Josephson ring modulator (JRM). We show that by tuning the external and shunt inductors, we should be able to take the best experimentally available JPAs and improve their saturation power by $\ensuremath{\approx}15\phantom{\rule{0.16em}{0ex}}\mathrm{dB}$. Finally, we argue that our methods and qualitative results are applicable to a broad range of cavity-based JPAs.

arXiv:1911.11176•Physical Review A•Apr 21, 2020•22 citations
Nondegenerate Josephson mixers (JMs), formed by coupling two different transmission-line resonators to Josephson ring modulators (JRMs), are vital and versatile devices capable of processing microwave signals at the quantum limit. Owing to the lossless nondegenerate three-wave mixing process enabled by the JRM, JMs can perform phase-preserving amplification of quantum signals, generate two-mode squeezed states, and perform noiseless frequency conversion. However, due to their limited bandwidth and saturation power, such resonator-based JMs are generally unable to simultaneously process frequency-multiplexed signals required in large quantum processors. To overcome this longstanding dual challenge, we redesign the JRM parameters by optimizing its inductances to suppress higher order mixing products and engineer its electromagnetic environment by incorporating lumped-element coupled-mode networks between the JRM and the two distinct ports of the JM. By implementing these strategies, we measure for JMs realized with four coupled modes per port, operated in amplification (conversion), bandwidths of about 400 MHz (700 MHz) with power reflections above 10 dB (below − 10 dB) and saturation powers of about − 110 dBm at 15 dB ( − 91 dBm at − 26 dB). Similarly, we demonstrate for a low external quality factor resonant-mode JM operated in conversion, a maximum bandwidth of about 670 MHz with power reflections below − 10 dB and a maximum saturation power of about − 86 dBm at − 17 dB. Such nondegenerate JMs with enhanced bandwidths and saturation powers could serve in a variety of frequency-multiplexed settings ranging from high-fidelity qubit readout and unidirectional routing of quantum signals to the generation of remote entanglement with continuous variables.
The Josephson ring modulator (JRM) is a device, based on Josephson tunnel junctions, capable of performing nondegenerate mixing in the microwave regime without losses. The generic scattering matrix of the device is calculated by solving coupled quantum Langevin equations. Its form shows that the device can achieve quantum-limited noise performance both as an amplifier and a mixer. Fundamental limitations on simultaneous optimization of performance metrics like gain, bandwidth, and dynamic range (including the effect of pump depletion) are discussed. We also present three possible integrations of the JRM as the active medium in a different electromagnetic environment. The resulting circuits, named Josephson parametric converters (JPC), are discussed in detail, and experimental data on their dynamic range are found to be in good agreement with theoretical predictions. We also discuss future prospects and requisite optimization of JPC as a preamplifier for qubit readout applications.
We present an optimal design in terms of gain, bandwidth and dynamical range for the Josephson mixer, the superconducting circuit performing three-wave mixing at microwave frequencies. In a compact all lumped-element based circuit with galvanically coupled ports, we demonstrate non degenerate amplification for microwave signals over a bandwidth up to 50 MHz for a power gain of 20 dB. The quantum efficiency of the mixer is shown to be about 70%\%% and its dynamical range reaches 5 quanta per inverse dynamical bandwidth.
One of the primary requirements for superconducting quantum information processors is high-fidelity, quantum non-demolition qubit readout. In superconducting circuits, we perform measurements with quantum-limited microwave amplifiers. These amplifiers are based on microwave cavities and powered by Josephson-junction based nonlinearities, which we drive to parametrically modulate the circuit and generate gain. However, cavity-based amplifiers generally suffer from a fixed gain-bandwidth product, a limited dynamic range, and the absence of directionality, and so they must be operated with external lossy microwave commercial components such as circulators. Many of these limitations can be circumvented by combining multiple parametric processes in a few-mode device, in particular by combining parametric drives which produce gain and those which produce gainless photon conversion. By combining balanced gain and conversion processes between a pair of modes, we have demonstrated transmission-only, phase-sensitive, gain-bandwidth-free amplification. We have also used measurements of transmon qubits with this mode of amplification to demonstrate its practical utility. More, by combining multiple instances of imbalanced gain and conversion processes among three modes, we have realized devices with non-reciprocal, transmission-only amplification, matched ports, and a large, gain-independent bandwidth. One of the biggest challenges in tuning multiple parametric processes is both inherent and dynamically-generated higher order nonlinearities in the device, which shift mode frequencies and parametric coupling strengths with pump power, preventing accurate balancing of the parametric processes. These can be controlled through engineering the Hamiltonian of the nonlinear element, in this thesis either a linearly-shunted Josephson Ring Modulator or SNAIL (Superconducting Nonlinear Asymmetric Inductive eLements), which for certain applied flux values can minimize or even change the sign of higher-order even nonlinearities. Additionally, we have explored a range of circuit parameters, allowing us to also control the relative size of odd-order nonlinearities. We have developed a series of prototypes which implement these concepts, and have achieved both high-dynamic range singly pumped amplifiers, and a promising platform for multi-parametric devices. We conclude by presenting recent progress towards implementing multiple parametric schemes that generates a practical directional amplifier, and discuss the remaining obstacles to a truly ideal parametric amplifiers.
Parametric amplification is essential for quantum measurement, enabling the amplification of weak microwave signals with minimal added noise. While Josephson-junction-based amplifiers have become standard in superconducting quantum circuits, their magnetic sensitivity, limited saturation power, and sub-kelvin operating requirements motivate the development of alternative nonlinear platforms. Here we demonstrate a two-mode kinetic-inductance parametric amplifier based on a pair of capacitively coupled Kerr-nonlinear resonators fabricated from NbTiN and NbN thin films. The distributed Kerr nonlinearity of these materials enables nondegenerate four-wave-mixing amplification with gains approaching 40 dB, gain-bandwidth products up to 6.9 MHz, and 1-dB compression powers two to three orders of magnitude higher than those of state-of-the-art Josephson amplifiers. A coupled-mode theoretical model accurately captures the pump-induced modification of the hybridized modes and quantitatively reproduces the observed signal and idler responses. The NbN device exhibits a significantly larger Kerr coefficient and superior gain-bandwidth performance, highlighting the advantages of high-kinetic-inductance materials. Our results establish coupled kinetic-inductance resonators as a robust platform for broadband, high-power, and magnetically resilient quantum-limited amplification, offering a scalable route for advanced readout in superconducting qubits, spin ensembles, quantum dots, and other microwave-quantum technologies.
Josephson parametric amplifiers (JPA) are nonlinear devices that are used for quantum sensing and qubit readout in the microwave regime. While JPAs regularly operate near the quantum limit, their gain saturates for very small (few-photon) input power. In a previous work, we showed that the saturation power of JPAs is not limited by pump depletion, but instead by the fourth-order nonlinearity of Josephson junctions, the nonlinear circuit elements that enables amplification in JPAs. Here, we present a systematic study of the nonlinearities in JPAs, show which nonlinearities limit the saturation power, and present a strategy for optimizing the circuit parameters for achieving the best possible JPA. For concreteness, we focus on JPAs that are constructed around a Josephson ring modulator (JRM). We show that by tuning the external and shunt inductors, we should be able to take the best experimentally available JPAs and improve their saturation power by $\ensuremath{\approx}15\phantom{\rule{0.16em}{0ex}}\mathrm{dB}$. Finally, we argue that our methods and qualitative results are applicable to a broad range of cavity-based JPAs.