We introduce a superconducting transconductance amplifier based on the thermal modulation of a SINIS (Superconductor-Insulator-Normal metal-Insulator-Superconductor) configuration. The device is composed of a normal metal island interfaced with two superconducting leads through tunnel barriers, establishing a voltage-biased symmetric SINIS setup. An additional NIS junction connects the island to a third superconducting lead, which serves as input. When the input voltage surpasses the superconducting gap, the resultant injection of quasiparticles increases the electronic temperature of the island, thereby modulating the SINIS current. We perform numerical analyzes of the device performance, influenced by input voltage, frequency, and bath temperature. At bath temperatures below 250 mK, the device shows a transconductance exceeding 4 mS and a current gain exceeding 45 dB. Both gain and transconductance maintain their levels up to 1 MHz, but decrease at higher frequencies, with a -3 dB cutoff around 10 MHz, and an average power dissipation of approximately 5 nW. Our simulations reveal a fully voltage-controlled, three-terminal superconducting amplifier characterized by high transconductance and gain, achieved through thermally mediated signal transduction. This architectural design presents a promising avenue for cryogenic amplification with reduced power dissipation and compatibility with current superconducting electronic systems.
We introduce a superconducting transconductance amplifier based on the thermal modulation of a SINIS (Superconductor-Insulator-Normal metal-Insulator-Superconductor) configuration. The device is composed of a normal metal island interfaced with two superconducting leads through tunnel barriers, establishing a voltage-biased symmetric SINIS setup. An additional NIS junction connects the island to a third superconducting lead, which serves as input. When the input voltage surpasses the superconducting gap, the resultant injection of quasiparticles increases the electronic temperature of the island, thereby modulating the SINIS current. We perform numerical analyzes of the device performance, influenced by input voltage, frequency, and bath temperature. At bath temperatures below 250 mK, the device shows a transconductance exceeding 4 mS and a current gain exceeding 45 dB. Both gain and transconductance maintain their levels up to 1 MHz, but decrease at higher frequencies, with a -3 dB cutoff around 10 MHz, and an average power dissipation of approximately 5 nW. Our simulations reveal a fully voltage-controlled, three-terminal superconducting amplifier characterized by high transconductance and gain, achieved through thermally mediated signal transduction. This architectural design presents a promising avenue for cryogenic amplification with reduced power dissipation and compatibility with current superconducting electronic systems.
We introduce a zero-bias superconducting voltage amplifier that harvests energy from a thermal gradient by exploiting negative differential resistance (NDR) in an asymmetric tunnel junction. The device is based on an asymmetric superconductor-insulator-superconductor (SIS) junction with an energy-gap ratio of Δ1/Δ2=0.5, connected in series with a load resistor. Owing to the superconducting bipolar thermoelectric effect, the current-voltage characteristic of the junction exhibits a region of NDR, in which the net current flows opposite to the applied voltage. This mechanism enables voltage amplification in the absence of any external electrical bias, relying solely on the temperature difference between the electrodes (TH≃1 K, TB≃20 mK). Numerical simulations predict a voltage gain of 20 dB, a 1 dB compression point at an input amplitude of 2 μV, and a total harmonic distortion below −50 dB. The input-referred noise is approximately 1 nV/Hz, with an associated thermal load on the order of nanowatts. The frequency response is broadband from near DC, with a −3 dB cutoff around 180 MHz, set by the RC time constant of the junction. Using Al-, Al-Cu-, and AlOx-based technologies, the amplifier is compatible with conventional superconducting circuit fabrication processes. These findings demonstrate that thermoelectric superconducting junctions can deliver bias-free voltage amplification from near DC up to about 200 MHz, making them promising candidates for transition-edge sensor readout, quantum circuit instrumentation, and low-frequency cryogenic signal processing.
We have developed a Superconductor-Insulator-Normal Metal-Insulator-Superconductor (SINIS) bolometer with a suspended normal metal bridge. The suspended bridge acts as a bolometric absorber with reduced heat losses to the substrate. Such bolometers were characterized at 100-350 mK bath temperatures and electrical responsivity of over 10 9 V/W was measured by dc heating the absorber through additional contacts. Suspended bolometers were also integrated in planar twin-slot and log-periodic antennas for operation in the submillimetre-band of radiation. The measured voltage response to radiation at 300 GHz and at 100 mK bath temperature is 3*10 8 V/W and a current response is 1.1*10 4 A/W which corresponds to a quantum efficiency of ~15 electrons per photon. An important feature of such suspended bolometers is the thermalization of electrons in the absorber heated by optical radiation, which in turn provides better quantum efficiency. This has been confirmed by comparison of bolometric response to dc and rf heating. We investigate the performance of direct SN traps and NIS traps with a tunnel barrier between the superconductor and normal metal trap. Increasing the volume of superconducting electrode helps to reduce overheating of superconductor. Influence of Andreev reflection and Kapitza resistance, as well as electron-phonon heat conductivity and thermal conductivity of N-wiring are estimated for such SINIS devices.
Various applications of quantum devices call for an accurate calibration of cryogenic amplification chains. To this end, we present an experimentally feasible calibration scheme and use it to accurately measure the total gain and noise temperature of an amplification chain by employing normal-metal–insulator–superconductor (NIS) junctions. Our method is based on the radiation emitted by inelastic electron tunneling across voltage-biased NIS junctions. We derive an analytical expression that relates the generated power to the applied bias voltage which is the only control parameter of the device. After the setup has been characterized using a standard voltage reflection measurement, the total gain and the noise temperature are extracted by fitting the analytical expression to the microwave power measured at the output of the amplification chain. The 1σ uncertainty of the total gain of 51.84 dB appears to be of the order of 0.10 dB.
We theoretically put forward the concept of a phase-controlled superconducting heat-flux quantum modulator. Its operation relies on phase-dependent heat current predicted to occur in temperature-biased Josephson tunnel junctions. The device behavior is investigated as a function of temperature bias across the junctions, bath temperature, and junctions asymmetry as well. In a realistic Al-based setup the structure could provide temperature modulation amplitudes up to ∼50 mK with flux-to-temperature transfer coefficients exceeding ∼125 mK/Φ0 below 1 K, and temperature modulation frequency of the order of a few MHz. The proposed structure appears as a promising building-block for the implementation of caloritronic devices operating at cryogenic temperatures.
The superconductor–insulator–normal metal–insulator–superconductor (SINIS) tunnel junction structure is the basic building block for various cryogenic devices. Microwave detectors, electron coolers, primary thermometers, and Aharonov–Bohm interferometers have been fabricated by various methods and measured at temperatures down to 100 mK. The manufacturing methods included Dolan-type shadow evaporation, Manhattan-type shadow evaporation, and magnetron sputtering with selective etching of superconducting and normal metal electrodes. Improvement in ultimate sensitivity is achieved by suspending the absorber above the substrate. Best responsivity of up to 30 electrons per photon at a frequency of 350 GHz, or 72000 A/W, and voltage responsivity up to 3.9 × 10 9 V/W were obtained with a black body radiation source and series of band-pass filters. The specially designed SINIS arrays are intended to detect 90 GHz radiation at the “Big Telescope Alt-azimuthal” (romanized Russian: “Bolshoi Teleskop Alt-azimutalnyi”, BTA) with noise equivalent power of less than 10 −16 W·Hz −1/2 . The receiver in a 3 He cryostat with an optical window was mounted at the Nasmyth focus of the BTA and tested at a temperature of 260 mK with a IMPATT diode radiation source.
The authors have modified the design of the superconducting current injection transistor (Super-CIT) for use in a distributed amplifier. The super-CIT consists of a resistively damped long Josephson junction in which the maximum Josephson current is modulated by the magnetic field produced by current in a control line. The device is modified by DC-coupling the control line from the Josephson junction so that the Super-CIT can be embedded in a distributed amplifier configuration. The distributed amplifier design is used to raise the input impedance and the power gain of the amplifier over a wide bandwidth. The small signal current gain of the device can be increased by biasing the Josephson junction in an asymmetric configuration. A simulation using practical values results in an amplifier with an input impedance of 6.5 Omega using only four devices, which produces 15 dB of gain into a 2.5- Omega load over a bandwidth of 90 GHz with very little reverse gain.>