Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2505.06155 · Journal of Low Temperature Physics

Non-degenerate Pumping of Superconducting Resonator Parametric Amplifier with Evidence of Phase-Sensitive Amplification

Songyuan Zhao, S. Withington, C. N. Thomas

Published Apr 9, 2026• 1 citation
arXivHTMLPDF

Abstract

Abstract Superconducting resonator parametric amplifiers are potentially important components for a wide variety of fundamental physics experiments and utilitarian applications. We propose and realise an operating scheme that achieves amplification through the use of non-degenerate pumps, which addresses two key challenges in the design of parametric amplifiers: non-continuous gain across the amplification band and pump tone removal. We have experimentally demonstrated the non-degenerate pumping scheme using a half-wave resonator amplifier based on NbN thin-film, and measured a peak gain of 26 dB and 3-dB bandwidth of 0.5 MHz. The two non-degenerate pump tones were positioned $$\sim 10$$ ∼ 10 bandwidths above and below the frequency at which peak gain occurs. We have found the non-degenerate pumping scheme to be more stable compared to the usual degenerate pumping scheme in terms of gain drift over time, by a factor of 4. This scheme also retains the usual flexibility of NbN resonator parametric amplifiers in terms of reliable amplification in a $$\sim 4$$ ∼ 4 K environment, and is suitable for cross-harmonic amplification. The use of pump tones at different frequencies allows phase-sensitive amplification when the signal tone is degenerate with the idler tone. A gain of 23 dB and squeezing ratio of 6 dB were measured.

DOI
10.1007/s10909-026-03407-6

Related papers

Superconducting resonator parametric amplifiers with intrinsic separation of pump and signal tones

Songyuan Zhao, S. Withington, Christopher N. Thomas

Abstract Superconducting resonator parametric amplifiers achieve ultra-low-noise amplification through the nonlinear kinetic inductance of thin-film superconductors. One of the main challenges to the operation of these devices is the separation of the strong pump tone from the signal tone after amplification has been achieved. In this paper, we propose and experimentally demonstrate a pump separation method based on operating a half-wave superconducting resonator amplifier behind a cryogenic circulator. Our pump separation scheme does not involve post-amplification interference, and thereby avoids the delicate phase matching of two different pump paths. We demonstrate the scheme using two-port half-wave resonator amplifiers based on superconducting NbN thin-films. We present measurements of gain profiles and degrees of pump separation for amplifiers having different coupling quality factors. On an amplifier having a coupling quality factor of ∼2000, we measured a peak signal gain of 15 dB whilst achieving pump separation of 12 dB . The amplifier was stable for continuous measurements, and the gain drift was measured to be 0.15 dB over an hour. The same amplifier was operated at 3.2 K and achieved a peak signal gain of 11 dB whilst having a pump separation factor of 10.5 dB . The pump separation scheme, and these promising results, will advance the development of superconducting resonator amplifiers as an important technology in quantum sensing.

arXiv:2406.02455•Journal of Physics D Applied Physics•Oct 16, 2024•7 citations

Nonlinear characteristics of Ti, Nb, and NbN superconducting resonators for parametric amplifiers

Songyuan Zhao, S. Withington, Christopher N. Thomas

Abstract Superconducting resonators and parametric amplifiers are important components in scientific systems such as kinetic inductance detector arrays, frequency-domain multiplexers for other superconducting bolometers, spin-ensemble based memories, and circuit quantum electrodynamics demonstrators. In this paper, we report microwave measurements of superconducting Ti, Nb, and NbN resonators and their use as parametric amplifiers. These half-wave resonators were fabricated under near identical sputtering and lithographic conditions to ensure a like-for-like comparison of material properties. We report a wide range of properties and behaviours in terms of transition temperatures, resistivities, rate-limiting nonlinear response times, nonlinear dissipation, signs of the nonlinear inductances and their dependences on temperature and resonance harmonic. We have successfully operated Nb and NbN resonators as high gain parametric amplifiers, achieving greater than 20 dB of power amplification. We have shown that for a half-wave resonator, amplification can be realised not only in the fundamental resonance but also in the higher harmonic resonances. Further, for materials with high transition temperatures, e.g. Nb and NbN, amplification can be achieved at ∼ 4 K, i.e. a temperature maintained by a pulse tube cooler. Finally, in materials systems that have very fast response times, e.g. NbN, we have found that a cross-harmonic type of amplification can be achieved by placing pump tone in a different resonant mode as the signal and the idler. This wide range of observations will have important implications on the design and application of superconducting parametric amplifiers.

arXiv:2306.00685•Superconductor Science and Technology•Aug 16, 2023•13 citations

Superconducting Parametric Amplifiers: Resonator Design and Role in Qubit Readout

Babak Mohammadian

Superconducting parametric amplifiers (SPAs) are critical components for ultralow-noise qubit readout in quantum computing, addressing the critical challenge of amplifying weak quantum signals without introducing noise that degrades coherence and computational fidelity. Unlike classical amplifiers, SPAs can achieve or closely approach quantum-limited performance, specifically the Standard Quantum Limit (SQL) of half a photon of added noise for phase-preserving amplification. The core principle of SPAs relies on parametric amplification, where energy is transferred from a strong pump tone to a weak input signal through non-dissipative nonlinear mixing processes. This is enabled by intrinsic nonlinearities in superconducting materials, primarily kinetic inductance in thin films (e.g., NbTiN, Al) and, more significantly, the Josephson effect in Josephson junctions. These nonlinear elements facilitate frequency mixing (three-wave or four-wave mixing) and can operate in phase-preserving or phase-sensitive amplification modes, with the latter allowing for noise squeezing below the SQL. This chapter emphasizes the significant role of resonator design in determining critical SPA performance metrics such as gain, bandwidth, and noise characteristics. It details both lumped-element (LC) and distributed-element (coplanar waveguide, CPW) resonators, discussing their unique properties, suitability for different frequency ranges, and the importance of achieving high-quality factors (Q) for efficient energy storage and minimal loss. A practical design and simulation of a meandered quarterwavelength CPW resonator coupled to a feed line is presented, illustrating how precise control over geometric parameters optimizes resonant frequency, coupling strength, and quality factor for high-fidelity qubit state discrimination.

quant-pharXiv:2511.20097•IntechOpen eBooks•Nov 26, 2025•0 citations

Parametric Amplification at Ka Band via Nonlinear Dynamics in Superconducting 3D Cavities

D. Banys, M. McCulloch, S. Azzoni +5 more

Abstract Modern parametric amplifiers are based on lithographically produced superconducting thin-film planar transmission line structures. These paramps rely on resonant structures with embedded nonlinear elements to stimulate intermodulation with a stronger pump tone that gives rise to signal gain when certain conditions are satisfied. Such paramps have not yet been realised in superconducting 3D waveguide resonators. Possible applications of these devices include detector systems that are based on 3D waveguide such as dark matter detectors and quantum computers. Reported here are the results of an investigation of a 30.64 GHz series circular waveguide resonance machined from bulk niobium showing parametric gain of up to 2 dB in the presence of a stronger pump tone 10 kHz above in frequency. The gain is largest on abrupt jumps of the transmission spectra of the resonance, which may be a result of weak-link formation on the superconducting surfaces.

Journal of Low Temperature Physics•Mar 18, 2020•3 citations

Experimental Demonstration of a Balanced Travelling Wave Parametric Amplifier

Nikita Klimovich, Peter K. Day, Henry G. Leduc +1 more

Superconducting travelling-wave parametric amplifiers (TWPAs) provide broadband gain, low added noise, and high dynamic range, making them attractive for applications requiring wide instantaneous bandwidth. This is crucial for amplifying multiplexed narrow band signals spread over a wide frequency range, such as qubit resonator arrays, or amplifying inherently wide band signals, such as in spectrometers or radiometers. In many cases, however, the useful bandwidth of a TWPA is limited by the production of the idler tone at an image frequency. For three-wave-mixing (3WM) TWPAs, for example, an input signal at $f_s$ is indistinguishable from one at $f_p - f_s$, which can produce spectral ambiguity when the input spectrum is broadband or not known in advance. We experimentally demonstrate a balanced architecture that doubles the instantaneous image-rejected bandwidth available to a 3WM TWPA by spatially separating the amplified signal from the output pump and generated idler, which resolves the sideband degeneracy. The architecture consists of two amplifiers connected between a pair of 180$^{\circ}$ hybrid couplers, with the signal and pump injected and output through the sum and difference ports, respectively. Using two kinetic-inductance TWPAs, we demonstrate approximately 20 dB of signal gain across nearly an octave of bandwidth, together with pump rejection below --20 dB and an average image rejection of approximately --15 dB over the operating band. These results establish balanced TWPAs as a practical approach to broadband parametric amplification, enabling improved contamination free bandwidth and eliminating the need for complex filtering.

physics.ins-detCross-listedarXiv:2610.23810•Oct 19, 2026•0 citations

X-band singly degenerate parametric amplification in a Josephson tunnel junction

J. Mygind, N. F. Pedersen, O. H. Soerensen

Preliminary measurements on a (quasi-) degenerate parametric amplifier using a single Josephson tunnel junction as the active element is reported. The pump frequency is at 18 GHz and the signal and idler frequencies are both at about 9 GHz. A power gain of 16 dB in a 4-MHz 3-dB bandwidth is achieved at the top of the cryostat.

Applied Physics Letters•Jan 1, 1978•24 citations
Abstract Superconducting resonator parametric amplifiers are potentially important components for a wide variety of fundamental physics experiments and utilitarian applications. We propose and realise an operating scheme that achieves amplification through the use of non-degenerate pumps, which addresses two key challenges in the design of parametric amplifiers: non-continuous gain across the amplification band and pump tone removal. We have experimentally demonstrated the non-degenerate pumping scheme using a half-wave resonator amplifier based on NbN thin-film, and measured a peak gain of 26 dB and 3-dB bandwidth of 0.5 MHz. The two non-degenerate pump tones were positioned ∼10\sim 10∼10 ∼ 10 bandwidths above and below the frequency at which peak gain occurs. We have found the non-degenerate pumping scheme to be more stable compared to the usual degenerate pumping scheme in terms of gain drift over time, by a factor of 4. This scheme also retains the usual flexibility of NbN resonator parametric amplifiers in terms of reliable amplification in a ∼4\sim 4∼4 ∼ 4 K environment, and is suitable for cross-harmonic amplification. The use of pump tones at different frequencies allows phase-sensitive amplification when the signal tone is degenerate with the idler tone. A gain of 23 dB and squeezing ratio of 6 dB were measured.
Abstract Superconducting resonator parametric amplifiers achieve ultra-low-noise amplification through the nonlinear kinetic inductance of thin-film superconductors. One of the main challenges to the operation of these devices is the separation of the strong pump tone from the signal tone after amplification has been achieved. In this paper, we propose and experimentally demonstrate a pump separation method based on operating a half-wave superconducting resonator amplifier behind a cryogenic circulator. Our pump separation scheme does not involve post-amplification interference, and thereby avoids the delicate phase matching of two different pump paths. We demonstrate the scheme using two-port half-wave resonator amplifiers based on superconducting NbN thin-films. We present measurements of gain profiles and degrees of pump separation for amplifiers having different coupling quality factors. On an amplifier having a coupling quality factor of ∼2000, we measured a peak signal gain of 15 dB whilst achieving pump separation of 12 dB . The amplifier was stable for continuous measurements, and the gain drift was measured to be 0.15 dB over an hour. The same amplifier was operated at 3.2 K and achieved a peak signal gain of 11 dB whilst having a pump separation factor of 10.5 dB . The pump separation scheme, and these promising results, will advance the development of superconducting resonator amplifiers as an important technology in quantum sensing.
Abstract Superconducting resonators and parametric amplifiers are important components in scientific systems such as kinetic inductance detector arrays, frequency-domain multiplexers for other superconducting bolometers, spin-ensemble based memories, and circuit quantum electrodynamics demonstrators. In this paper, we report microwave measurements of superconducting Ti, Nb, and NbN resonators and their use as parametric amplifiers. These half-wave resonators were fabricated under near identical sputtering and lithographic conditions to ensure a like-for-like comparison of material properties. We report a wide range of properties and behaviours in terms of transition temperatures, resistivities, rate-limiting nonlinear response times, nonlinear dissipation, signs of the nonlinear inductances and their dependences on temperature and resonance harmonic. We have successfully operated Nb and NbN resonators as high gain parametric amplifiers, achieving greater than 20 dB of power amplification. We have shown that for a half-wave resonator, amplification can be realised not only in the fundamental resonance but also in the higher harmonic resonances. Further, for materials with high transition temperatures, e.g. Nb and NbN, amplification can be achieved at ∼ 4 K, i.e. a temperature maintained by a pulse tube cooler. Finally, in materials systems that have very fast response times, e.g. NbN, we have found that a cross-harmonic type of amplification can be achieved by placing pump tone in a different resonant mode as the signal and the idler. This wide range of observations will have important implications on the design and application of superconducting parametric amplifiers.
Superconducting parametric amplifiers (SPAs) are critical components for ultralow-noise qubit readout in quantum computing, addressing the critical challenge of amplifying weak quantum signals without introducing noise that degrades coherence and computational fidelity. Unlike classical amplifiers, SPAs can achieve or closely approach quantum-limited performance, specifically the Standard Quantum Limit (SQL) of half a photon of added noise for phase-preserving amplification. The core principle of SPAs relies on parametric amplification, where energy is transferred from a strong pump tone to a weak input signal through non-dissipative nonlinear mixing processes. This is enabled by intrinsic nonlinearities in superconducting materials, primarily kinetic inductance in thin films (e.g., NbTiN, Al) and, more significantly, the Josephson effect in Josephson junctions. These nonlinear elements facilitate frequency mixing (three-wave or four-wave mixing) and can operate in phase-preserving or phase-sensitive amplification modes, with the latter allowing for noise squeezing below the SQL. This chapter emphasizes the significant role of resonator design in determining critical SPA performance metrics such as gain, bandwidth, and noise characteristics. It details both lumped-element (LC) and distributed-element (coplanar waveguide, CPW) resonators, discussing their unique properties, suitability for different frequency ranges, and the importance of achieving high-quality factors (Q) for efficient energy storage and minimal loss. A practical design and simulation of a meandered quarterwavelength CPW resonator coupled to a feed line is presented, illustrating how precise control over geometric parameters optimizes resonant frequency, coupling strength, and quality factor for high-fidelity qubit state discrimination.
Abstract Modern parametric amplifiers are based on lithographically produced superconducting thin-film planar transmission line structures. These paramps rely on resonant structures with embedded nonlinear elements to stimulate intermodulation with a stronger pump tone that gives rise to signal gain when certain conditions are satisfied. Such paramps have not yet been realised in superconducting 3D waveguide resonators. Possible applications of these devices include detector systems that are based on 3D waveguide such as dark matter detectors and quantum computers. Reported here are the results of an investigation of a 30.64 GHz series circular waveguide resonance machined from bulk niobium showing parametric gain of up to 2 dB in the presence of a stronger pump tone 10 kHz above in frequency. The gain is largest on abrupt jumps of the transmission spectra of the resonance, which may be a result of weak-link formation on the superconducting surfaces.
Superconducting travelling-wave parametric amplifiers (TWPAs) provide broadband gain, low added noise, and high dynamic range, making them attractive for applications requiring wide instantaneous bandwidth. This is crucial for amplifying multiplexed narrow band signals spread over a wide frequency range, such as qubit resonator arrays, or amplifying inherently wide band signals, such as in spectrometers or radiometers. In many cases, however, the useful bandwidth of a TWPA is limited by the production of the idler tone at an image frequency. For three-wave-mixing (3WM) TWPAs, for example, an input signal at fsf_sfs​ is indistinguishable from one at fp−fsf_p - f_sfp​−fs​, which can produce spectral ambiguity when the input spectrum is broadband or not known in advance. We experimentally demonstrate a balanced architecture that doubles the instantaneous image-rejected bandwidth available to a 3WM TWPA by spatially separating the amplified signal from the output pump and generated idler, which resolves the sideband degeneracy. The architecture consists of two amplifiers connected between a pair of 180∘^{\circ}∘ hybrid couplers, with the signal and pump injected and output through the sum and difference ports, respectively. Using two kinetic-inductance TWPAs, we demonstrate approximately 20 dB of signal gain across nearly an octave of bandwidth, together with pump rejection below --20 dB and an average image rejection of approximately --15 dB over the operating band. These results establish balanced TWPAs as a practical approach to broadband parametric amplification, enabling improved contamination free bandwidth and eliminating the need for complex filtering.