Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2501.11418 · Applied Optics

Superheterodyne Rydberg S-band receiver with a multi-tone local oscillator based on an atomic transition loop

Jan Nowosielski, Mateusz Mazelanik, Wojciech Wasilewski, Michal P. Parniak

Published Jun 17, 2025• 2 citations
arXivHTMLPDF

Abstract

Atomic-vapor sensors based on Rydberg atoms now face a transition toward practical applications, with several outstanding challenges. To achieve the best sensitivities, a superheterodyne mode of operation is desired, which requires the presence of a local oscillator in the vapor cell. This local oscillator hinders several advantages of the sensor, such as stealthy and all-optical operation. We propose and realize a detection scheme that avoids some of those problems by using multi-tone mixing, where direct usage of the local oscillator at the same frequency is not required. Our scheme is further elaborated on using efficient theoretical methods to predict the performance of the sensor. Our sensor operates at the S-band frequency, known for its usage in IEEE 802.11 (Wi-Fi) networks, without interfering with the signal itself.

DOI
10.1364/ao.557585

Related papers

All-optical phase-referenced microwave sensing in Rydberg alkali vapors

Sebastian Borówka, Mateusz Mazelanik, Wojciech Wasilewski +1 more

One of the advantages of Rydberg atom-based detection of microwave and THz fields is weak distortion of the measured field, allowing for precise and stealthy detection. However, recent developments focused on using Rydberg atoms as a RF mixer with a local oscillator field in a superheterodyne-type detection that is no longer all-optical, as the local oscillator antenna has to be a part of the detector. Here we undertake the task of developing an all-optical detection, where the phase reference is provided not in local oscillator, but instead in the polarization of atoms. To realize this feature, we access the 13.9 GHz Rydberg transition in rubidium with two separate optical excitation paths and measure the beating of probe field. We report an overall detection sensitivity of 176 nV/cm/ √Hz and reliable operation up to 3.5 mV/cm of RF field, results that are parallel to superheterodyne detection method demonstrated in the same setup. The results of this work are largely based on an earlier conducted study, published as a preprint.1 The present manuscript is meant to serve as an appendix to this work, focusing on putting this research in the context of all-optical detection schemes.

SPIE Quantum Technologies for Defence and Security•Nov 15, 2024•0 citations

High-sensitivity and low-harmonic microwave detection using Rydberg atoms based on a loop-level structure

Yu Tang, Shuang Ren, Chuang Yang +3 more

We propose and investigate a Rydberg atom sensor based on a loop-level structure, which utilizes the eigenfrequencies of the energy levels as a reference. This design eliminates the need for the local oscillator (LO) electric field required in the traditional superheterodyne structure while maintaining a linear relationship between the readout signal and the microwave (MW) electric field to be measured, along with exhibiting significantly lower harmonic distortion. For experimental validation, we implemented a cesium atomic system based on the loop five-level structure. The system achieved a sensitivity of 62 nVcm -1 Hz -1/2 and maintained 30 dB of harmonic suppression even near the nonlinear operational region under the strong electric field, which is approximately 20 dB higher than that of the superheterodyne structure. This work demonstrates that loop-level-based atomic sensors enable high-sensitivity and wide-dynamic-range (including nonlinear region) MW detection, making them particularly suitable for receiving frequency- and phase-modulated signals that are insensitive to power variations.

Optics Express•May 9, 2025•1 citation

Continuous-Frequency Microwave Heterodyne Detection in an Atomic Vapor Cell

Xiao-Hong Liu, Kai-Yu Liao, Zuan-Xian Zhang +8 more

Atomic heterodyne dressed by a local oscillator resonant with Rydberg transitions allows high sensitivity and robust phase measurement of a microwave electric field, but it is typically limited to detection of discrete frequencies within the narrow bandwidth of Rydberg transitions. Here we demonstrate an atomic heterodyne scheme for continuous-frequency electric field measurement based on multilevel Rydberg atoms in a room-temperature vapor cell. Driven by two off-resonant microwaves acting as a tunable local oscillator field, the heterodyne receiver can retrieve the amplitude, phase, and frequency information of signal microwave in a continuous frequency band. In our experiment, the receiver achieves an electric field sensitivity of up to $1.5\phantom{\rule{0.2em}{0ex}}\ensuremath{\mu}\mathrm{V}\phantom{\rule{0.2em}{0ex}}{\mathrm{cm}}^{\ensuremath{-}1}\phantom{\rule{0.2em}{0ex}}{\mathrm{Hz}}^{\ensuremath{-}1/2}$, 80-dB linear dynamic range, and over 1 GHz of continuous frequency range. We also demonstrate the reliable reception of continuously tunable phase-modulated carriers in the digital communication. This work will facilitate the application of atomic heterodyne in the areas such as radar technique, radio monitoring, and radio astronomy.

Physical Review Applied•Nov 2, 2022•70 citations

Rydberg Atoms as Tunable All-Optical and Phase-Sensitive Sensors of Microwave Fields

Sebastian Borówka, Bartosz Kasza, Mateusz Mazelanik +2 more

The detection of microwave (MW) fields with room-temperature Rydberg atomic vapors is a novel technique of optical sensing, introducing a range of merits typically not possible to achieve with conventional antennas [1]. Firstly, the atomic response to MW fields is dependent on a given transition dipole moment between Rydberg energy levels - as this value can be precisely derived from the theory of alkali atoms, e.g. rubidium, Rydberg sensors are intrinsically calibrated and there is no dependency on particular device. Secondly, the detector does not contain any metal parts (apart from trace amount of rubidium), introducing very little distortion to the measured field, so the detection is stealthy, and the detector is practically invulnerable even to strong fields. Typically, however, the best state-of-the-art performance is achieved with an additional local oscillator MW field [2], emitted from the antenna, in which case the scheme is no longer all-optical and some advantages are lost.

Conference on Lasers and Electro-Optics Europe & European Quantum Electronics Conference (CLEO/Europe-EQEC)•Jun 23, 2025•0 citations

Nonlinearities in atomic radio receivers: Harmonic and intermodulation distortion

Luís F. Gonçalves, Teng Zhang, Georg A. Raithel +1 more

Rydberg sensors offer a unique approach to radio-frequency (rf) detection, leveraging the high sensitivity and quantum properties of highly excited atomic states to achieve performance levels beyond classical technologies. Nonlinear responses and distortion behavior in Rydberg atom receivers are critical to evaluating and establishing performance metrics and capabilities such as spur-free dynamic range and tolerance to unwanted interfering signals. We report here on the measurement and characterization of nonlinear behavior and spurious response of a Rydberg atomic heterodyne receiver. Single-tone and two-tone testing procedures are developed and implemented for measurement of harmonic and intermodulation distortion in Rydberg atomic receivers based on multiphoton Rydberg spectroscopy and radio-frequency heterodyne signal detection and demodulation in an atomic vapor. For a predetermined set of atomic receiver parameters and rf carrier wave in the super high frequency band near-resonant to a cesium Rydberg transition, we measure and characterize atomic receiver selectivity, bandwidth, roll-off, compression point (P1dB), second-order (IP2) and third-order (IP3) intercepts, and spur-free dynamic range. Receiver intermodulation distortion is characterized for the case of an interfering signal wave applied at two frequency offsets relative to the near-resonant reference local oscillator, Δ F / F = 10 − 4 at 6 dB and 10 − 6 at 22 dB single-tone bandwidths, respectively. We observe that under suitable operating conditions the atomic receiver can exhibit a suppression of harmonic and intermodulation distortion relative to that of classical receiver mixer amplifiers.

arXiv:2412.16366•APS Open Science•Jul 14, 2026•3 citations

A Cs Rydberg Atomic Microwave Oscillator for Electric Field Sensing

He Wang, David Rosser, Michael J. Mazon +1 more

In this paper, we report an atomic oscillator in Ku band and its application for electric field (E-field) sensing with Cs Rydberg atoms in a room-temperature vapor cell. The oscillator is associated with the Cs Rydberg transition of 362D5/2– 372P3/2at 16.316 GHz which is generated with a two-laser double-resonance excitation. We characterized the energetics and the dipole moment of the Rydberg transition and used Electromagnetically Induced Transparency (EIT) and Autler-Townes (AT) effects for detecting continuous and amplitude/frequency modulated microwave E-fields. To enhance the oscillator’s response to weak signals, a superheterodyne technique was incorporated into the Rydberg oscillator system, which resulted in an improvement in the oscillator’s sensitivity by 100 times. Furthermore, our modeling shows that the Cs Rydberg atomic oscillator can be tuned to broad frequency ranges from MHz to THz for various RF applications.

Joint Conference of the European Frequency and Time Forum and IEEE International Frequency Control Symposium (EFTF/IFCS)•May 15, 2023•1 citation
Atomic-vapor sensors based on Rydberg atoms now face a transition toward practical applications, with several outstanding challenges. To achieve the best sensitivities, a superheterodyne mode of operation is desired, which requires the presence of a local oscillator in the vapor cell. This local oscillator hinders several advantages of the sensor, such as stealthy and all-optical operation. We propose and realize a detection scheme that avoids some of those problems by using multi-tone mixing, where direct usage of the local oscillator at the same frequency is not required. Our scheme is further elaborated on using efficient theoretical methods to predict the performance of the sensor. Our sensor operates at the S-band frequency, known for its usage in IEEE 802.11 (Wi-Fi) networks, without interfering with the signal itself.
One of the advantages of Rydberg atom-based detection of microwave and THz fields is weak distortion of the measured field, allowing for precise and stealthy detection. However, recent developments focused on using Rydberg atoms as a RF mixer with a local oscillator field in a superheterodyne-type detection that is no longer all-optical, as the local oscillator antenna has to be a part of the detector. Here we undertake the task of developing an all-optical detection, where the phase reference is provided not in local oscillator, but instead in the polarization of atoms. To realize this feature, we access the 13.9 GHz Rydberg transition in rubidium with two separate optical excitation paths and measure the beating of probe field. We report an overall detection sensitivity of 176 nV/cm/ √Hz and reliable operation up to 3.5 mV/cm of RF field, results that are parallel to superheterodyne detection method demonstrated in the same setup. The results of this work are largely based on an earlier conducted study, published as a preprint.1 The present manuscript is meant to serve as an appendix to this work, focusing on putting this research in the context of all-optical detection schemes.
We propose and investigate a Rydberg atom sensor based on a loop-level structure, which utilizes the eigenfrequencies of the energy levels as a reference. This design eliminates the need for the local oscillator (LO) electric field required in the traditional superheterodyne structure while maintaining a linear relationship between the readout signal and the microwave (MW) electric field to be measured, along with exhibiting significantly lower harmonic distortion. For experimental validation, we implemented a cesium atomic system based on the loop five-level structure. The system achieved a sensitivity of 62 nVcm -1 Hz -1/2 and maintained 30 dB of harmonic suppression even near the nonlinear operational region under the strong electric field, which is approximately 20 dB higher than that of the superheterodyne structure. This work demonstrates that loop-level-based atomic sensors enable high-sensitivity and wide-dynamic-range (including nonlinear region) MW detection, making them particularly suitable for receiving frequency- and phase-modulated signals that are insensitive to power variations.
Atomic heterodyne dressed by a local oscillator resonant with Rydberg transitions allows high sensitivity and robust phase measurement of a microwave electric field, but it is typically limited to detection of discrete frequencies within the narrow bandwidth of Rydberg transitions. Here we demonstrate an atomic heterodyne scheme for continuous-frequency electric field measurement based on multilevel Rydberg atoms in a room-temperature vapor cell. Driven by two off-resonant microwaves acting as a tunable local oscillator field, the heterodyne receiver can retrieve the amplitude, phase, and frequency information of signal microwave in a continuous frequency band. In our experiment, the receiver achieves an electric field sensitivity of up to $1.5\phantom{\rule{0.2em}{0ex}}\ensuremath{\mu}\mathrm{V}\phantom{\rule{0.2em}{0ex}}{\mathrm{cm}}^{\ensuremath{-}1}\phantom{\rule{0.2em}{0ex}}{\mathrm{Hz}}^{\ensuremath{-}1/2}$, 80-dB linear dynamic range, and over 1 GHz of continuous frequency range. We also demonstrate the reliable reception of continuously tunable phase-modulated carriers in the digital communication. This work will facilitate the application of atomic heterodyne in the areas such as radar technique, radio monitoring, and radio astronomy.
The detection of microwave (MW) fields with room-temperature Rydberg atomic vapors is a novel technique of optical sensing, introducing a range of merits typically not possible to achieve with conventional antennas [1]. Firstly, the atomic response to MW fields is dependent on a given transition dipole moment between Rydberg energy levels - as this value can be precisely derived from the theory of alkali atoms, e.g. rubidium, Rydberg sensors are intrinsically calibrated and there is no dependency on particular device. Secondly, the detector does not contain any metal parts (apart from trace amount of rubidium), introducing very little distortion to the measured field, so the detection is stealthy, and the detector is practically invulnerable even to strong fields. Typically, however, the best state-of-the-art performance is achieved with an additional local oscillator MW field [2], emitted from the antenna, in which case the scheme is no longer all-optical and some advantages are lost.
Rydberg sensors offer a unique approach to radio-frequency (rf) detection, leveraging the high sensitivity and quantum properties of highly excited atomic states to achieve performance levels beyond classical technologies. Nonlinear responses and distortion behavior in Rydberg atom receivers are critical to evaluating and establishing performance metrics and capabilities such as spur-free dynamic range and tolerance to unwanted interfering signals. We report here on the measurement and characterization of nonlinear behavior and spurious response of a Rydberg atomic heterodyne receiver. Single-tone and two-tone testing procedures are developed and implemented for measurement of harmonic and intermodulation distortion in Rydberg atomic receivers based on multiphoton Rydberg spectroscopy and radio-frequency heterodyne signal detection and demodulation in an atomic vapor. For a predetermined set of atomic receiver parameters and rf carrier wave in the super high frequency band near-resonant to a cesium Rydberg transition, we measure and characterize atomic receiver selectivity, bandwidth, roll-off, compression point (P1dB), second-order (IP2) and third-order (IP3) intercepts, and spur-free dynamic range. Receiver intermodulation distortion is characterized for the case of an interfering signal wave applied at two frequency offsets relative to the near-resonant reference local oscillator, Δ F / F = 10 − 4 at 6 dB and 10 − 6 at 22 dB single-tone bandwidths, respectively. We observe that under suitable operating conditions the atomic receiver can exhibit a suppression of harmonic and intermodulation distortion relative to that of classical receiver mixer amplifiers.
In this paper, we report an atomic oscillator in Ku band and its application for electric field (E-field) sensing with Cs Rydberg atoms in a room-temperature vapor cell. The oscillator is associated with the Cs Rydberg transition of 362D5/2– 372P3/2at 16.316 GHz which is generated with a two-laser double-resonance excitation. We characterized the energetics and the dipole moment of the Rydberg transition and used Electromagnetically Induced Transparency (EIT) and Autler-Townes (AT) effects for detecting continuous and amplitude/frequency modulated microwave E-fields. To enhance the oscillator’s response to weak signals, a superheterodyne technique was incorporated into the Rydberg oscillator system, which resulted in an improvement in the oscillator’s sensitivity by 100 times. Furthermore, our modeling shows that the Cs Rydberg atomic oscillator can be tuned to broad frequency ranges from MHz to THz for various RF applications.