Manipulating the electromagnetic spectrum at the single-photon level is fundamental for quantum experiments. In the visible and infrared ranges, this can be accomplished with atomic quantum emitters, and with superconducting qubits such control is extended to the microwave range (below 10 GHz). Meanwhile, the region between these two energy ranges presents an unexplored opportunity for innovation. We bridge this gap by scaling up a superconducting qubit to the millimeter-wave range (near 100 GHz). Working in this energy range greatly reduces sensitivity to thermal noise compared to microwave devices, enabling operation at significantly higher temperatures, up to 1 K. This has many advantages by removing the dependence on rare 3 He for refrigeration, simplifying cryogenic systems, and providing orders-of-magnitude higher cooling power, lending the flexibility needed for novel quantum sensing and hybrid experiments. Using low-loss niobium trilayer junctions, we realize a qubit at 72 GHz cooled to 0.87 K using only 4 He . We perform Rabi oscillations to establish control over the qubit state, and measure relaxation and dephasing times of 15.8 and 17.4 ns, respectively. This demonstration of a millimeter-wave quantum emitter offers exciting prospects for enhanced sensitivity thresholds in high-frequency photon detection, provides new options for quantum transduction and for scaling up and speeding up quantum computing, enables integration of quantum systems where 3 He refrigeration units are impractical, and, importantly, paves the way for quantum experiments exploring a novel energy range.
Manipulating the electromagnetic spectrum at the single-photon level is fundamental for quantum experiments. In the visible and infrared ranges, this can be accomplished with atomic quantum emitters, and with superconducting qubits such control is extended to the microwave range (below 10 GHz). Meanwhile, the region between these two energy ranges presents an unexplored opportunity for innovation. We bridge this gap by scaling up a superconducting qubit to the millimeter-wave range (near 100 GHz). Working in this energy range greatly reduces sensitivity to thermal noise compared to microwave devices, enabling operation at significantly higher temperatures, up to 1 K. This has many advantages by removing the dependence on rare 3 He for refrigeration, simplifying cryogenic systems, and providing orders-of-magnitude higher cooling power, lending the flexibility needed for novel quantum sensing and hybrid experiments. Using low-loss niobium trilayer junctions, we realize a qubit at 72 GHz cooled to 0.87 K using only 4 He . We perform Rabi oscillations to establish control over the qubit state, and measure relaxation and dephasing times of 15.8 and 17.4 ns, respectively. This demonstration of a millimeter-wave quantum emitter offers exciting prospects for enhanced sensitivity thresholds in high-frequency photon detection, provides new options for quantum transduction and for scaling up and speeding up quantum computing, enables integration of quantum systems where 3 He refrigeration units are impractical, and, importantly, paves the way for quantum experiments exploring a novel energy range.
Current state-of-the-art superconducting microwave qubits are cooled to extremely low temperatures to avoid sources of decoherence. Higher qubit operating temperatures would significantly increase the cooling power available, which is desirable for scaling up the number of qubits in quantum computing architectures and integrating qubits in experiments requiring increased heat dissipation. To operate superconducting qubits at higher temperatures, it is necessary to address both quasiparticle decoherence (which becomes significant for aluminum junctions above 160 mK) and dephasing from thermal microwave photons (which are problematic above 50 mK). Using low-loss niobium-trilayer junctions, which have reduced sensitivity to quasiparticles due to the higher superconducting transition temperature of niobium, we fabricate transmons with higher frequencies than previously studied, up to 24 GHz. We measure decoherence and dephasing times of about 1 μ s , corresponding to average qubit quality factors of approximately 10 5 , and find that decoherence is unaffected by quasiparticles up to 1 K . Without relaxation from quasiparticles, we are able to explore dephasing from purely thermal sources, finding that our qubits can operate up to approximately 250 mK while maintaining similar performance. The thermal resilience of these qubits creates new options for scaling up quantum processors, enables hybrid quantum experiments with high heat-dissipation budgets, and introduces a material platform for even-higher-frequency qubits. Published by the American Physical Society 2024
Atoms and photons, two things so different but yet so alike. The former, the building block of matter, something we learn about in school and imagine it as some tiny marbles encircled by other tinier marbles. The latter, an electromagnetic wave, a light particle or an excitation of the electromagnetic field. Quantum mechanics tells us about the properties of these two entities. And even if it sounds, looks and writes counter-intuitive, it has proven right for over a century now. In this work, I elaborate on how we tested the laws of quantum mechanics and how we used them learn more about the tiny building blocks of nature and the fields they use to talk to each other. The atoms we use, are artificial. Superconducting qubits, small electrical circuits with quantized energy levels behave like electrons that transition between different orbitals in an atom. One of the qubits' advantages, is also a big disadvantage. We design the circuits' energy levels and fabricate them in a cleanroom. This allows for arbitrary spaced energy levels but in contrast to real atoms, prevents two superconducting qubits from being alike. Still, this qubit platform is one of the frontrunners for future quantum computing technology and testing fundamental physics due to their scalability. We interface superconducting qubits, which operate in the GHz regime, with microwave photons. We use 3D aluminum cavities as mediators between qubits and photons. The cavities allow for non-destructive readout of the qubit state, they shield the qubits from noise at the qubit frequency and they give us an easy way to frequency-tune these joint systems. We need to operate superconducting qubits and their cavities at millikelvin temperatures in dilution refrigerators. At higher temperatures, superconductivity suffers and even worse, the environment is filled with thermal noise photons. This poses a fundamental limitation on the scalability of superconducting qubit devices. Also connecting multiple devices in different fridges does not work over room temperature links because the microwave photons used for this purpose will be covered in noise and the quantum information they carry, will be unusable. Infrared photons do not suffer from this noise problem since there are close to zero thermal noise photons at their frequencies at room temperature. We cannot simply interface superconducting devices with optical photons due their frequency mismatch and the destructive effect of optical photons on superconductors. Therefore, we use microwave-to-optics transducers that allow to convert microwave photons into optical ones and vice-versa. The transducers that we use are macroscopic electro-optic transducers using the Pockels effect in a disk-shaped Lithium Niobate whispering gallery mode resonator. By using a strong optical pump, photons from the two frequency domains experience a beam-splitter interaction and get converted from one to the other. We measure the generated optical photons using elaborate optical setups, optical heterodyning and single photon detectors to gain knowledge about the qubit state or the converted microwave photons. Bridging the microwave and the optical world allows us to take advantage of both of their strengths but it also requires deep knowledge about both of their working principles. In this work, we describe two experiments that our group conducted to showcase the opportunities that arise from interfacing superconducting qubits with optical photons but also the pitfalls, one may encounter on the way. In the first experiment, we managed to all-optically read out a superconducting qubit. We show that the assignment fidelity, the probability that a measurement of the qubit state matches the prepared state, is close to equal for all-optical, microwave-to-optics and conventional microwave readout. We show T1 and T2 measurements for all three readout types and give an analysis of the noise caused by the optics. Finally, we show that the infrared light does not affect the qubit performance in a negative way but that the heating it causes does. This is an important insight that we used in the next experiment. The second experiment is the upconversion of itinerant single microwave photons to the optical domain. We show that we can generate single microwave photons from a qubit-cavity system. We upconvert these single photons, measure them with a single photon detector and reconstruct their shape. By conducting a single photon Rabi measurement, we show correlations between the microwave and the optical domain. And by thorough signal-to-noise measurements and noise analysis, we find that we can generate single infrared photons with high signal-to-noise ratio 5.1 and low transducer added noise (<0.012 quanta). We show that this measurement creates a path towards entanglement of a superconducting qubit and an optical photon and what parameters need to be improved to achieve it. Additionally, this experiment is a proof of principle for an on-demand infrared single photon source. More generally, it allows to link microwave quantum technology in general to the optical domain.
Photonic addressing of superconducting circuits has been proposed to overcome wiring complexity and heat-load challenges. However, such superconducting-photonic links suffer from an efficiency-noise trade-off that limits scalability. This trade-off arises because increasing power conversion efficiency entails reducing optical power, which makes the converted signal susceptible to shot noise. We analyze this trade-off and find that the laser-driven qubit gate infidelity scales inversely with the number of photons used. While methods such as nonlinear detection or squeezed light could mitigate this effect, we consider generating higher-frequency electrical signals, such as millimeter waves (100 GHz), using laser light. At these higher frequencies, circuits have higher operating temperatures and cooling power budgets and alleviate constraints posed by the trade-off. Therefore, we demonstrate an optically driven cryogenic millimeter-wave source with a maximum power efficiency of 8 × 10 − 5 that can generate a maximum of 0.7 μ W of 80 GHz power, with a 1200 -thermal-photon equivalent of added noise at 4 K . Using this source, we perform frequency-domain spectroscopy of superconducting Nb Ti N resonators at 80–90 GHz. Our results show a promising approach to lessen the efficiency-noise constraints on superconducting-photonic links, while leveraging the benefits of photonic signal delivery. Further optimization of power efficiency and noise at high frequencies could make scalable photonic control of superconducting qubits viable at temperatures exceeding 1 K . Published by the American Physical Society 2024
The microwave-driven dynamics of the superconducting phase difference across a Josephson junction is now widely employed in superconducting qubits and quantum circuits. With the typical energy level separation frequency of several GHz, cooling these quantum devices to the ground state requires temperatures below 100 mK. Pushing the operation frequency of superconducting qubits up may allow for operation of superconducting qubits at 1 K and even higher temperatures. Here we present measurements of the switching currents of niobium/aluminum-aluminum oxide/niobium Josephson junctions in the presence of millimeter-wave radiation at frequencies above 100 GHz. The observed switching current distributions display clear double-peak structures, which result from the resonant escape of the Josephson phase from a stationary state. We show that the data can be well explained by the strong-driving model including the irradiation-induced suppression of the potential barrier. While still being measured in the quasi-classical regime, our results point towards a feasibility of operating phase qubits around 100 GHz.
The microwave-driven dynamics of the superconducting phase difference across a Josephson junction is now widely employed in superconducting qubits and quantum circuits. With their typical energy level separation frequency being several GHz, cooling these quantum devices to the ground state requires temperatures below 100 mK. Pushing the operation frequency of superconducting qubits up may allow for operation of superconducting qubits at 1 K and even higher temperatures. Here, we present measurements of the switching currents of niobium/aluminum–aluminum oxide/niobium Josephson junctions in the presence of millimeter-wave radiation at frequencies above 100 GHz. The observed switching current distributions display clear double-peak structures, which result from the resonant escape of the Josephson phase from a stationary state. We show that the data can be well explained by the strong-driving model including the irradiation-induced suppression of the potential barrier. While still being measured in the quasi-classical regime, our results point toward a feasibility of operating phase qubits around 100 GHz.
Abstract Superconducting qubits are multilevel micro-fabricated artificial atoms based on superconducting materials. They are mainly operated in the low microwave frequency range (2–8 GHz) and require to be cooled below 20 mK to maintain quantum coherence. They enable precise engineering of transition frequencies and coupling strengths, facilitating advancements in quantum information processing and light-matter interactions. The field has evolved from early devices, characterized by short coherence times, to modern architectures with improved noise resilience, scalability, and fidelity. Better performances have been achieved through innovations in materials, fabrication, control electronics, and circuit design, enabling qubits with millisecond coherence times and gate fidelities exceeding 99.9%. However, challenges remain in mitigating two-level system defects, scaling devices, and addressing the cryogenic and infrastructure needs of larger quantum processing units. Current research focuses on modular and scalable architectures, error correction, and application. The field’s progress highlights the potential for superconducting qubits to drive advancements in quantum computation.