Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2405.15949 · Quantum Science and Technology

Daemonic quantum battery charged by thermalization

Matias Araya Satriani, Felipe Barra

Published Aug 23, 2024• 9 citations
arXivHTMLPDF

Abstract

Abstract The reduced state of a small system strongly coupled to a charger in thermal equilibrium may be athermal and used as a small battery once disconnected. By harnessing the battery-charger correlations, the battery’s extractable energy can increase above the ergotropy. We introduce a protocol that uses a quantum system as a memory that measures the charger and leaves the battery intact in its charged state. Using the information gained from the measurement, the daemonic ergotropy of the battery is extracted. Then the battery is reconnected to the charger, thermalizing and charging it. However, the memory should return to its initial standard state to close the thermodynamic cycle. Thus, on the one hand, the work cost of the cycle is the sum of the disconnecting and reconnecting battery-charger work plus the measurement and erasure work. On the other hand, the extracted energy is the daemonic ergotropy of the battery plus the ergotropy of the memory. The ratio of these quantities defines the efficiency of the cycle. The protocol is exemplified by a modified transverse spin 1/2 Ising chain, one spin functioning as the battery and the others as the charger. The memory is another auxiliary spin 1/2. We found pairs of measurement schemes from which we extract the same daemonic ergotropy from the battery, they dissipate the same amount of energy, and one leaves the memory in an active state, the other in a passive state. We study the memory’s ergotropy and the daemonic ergotropy of the battery. We find that with measurements, the efficiency can surpass that of the unmeasured protocol, given conditions on temperature, coupling, and choice of the measurement operators.

DOI
10.1088/2058-9565/ad7316

Related papers

Quantum batteries at the verge of a phase transition

Felipe Barra, Karen V. Hovhannisyan, Alberto Imparato

Abstract Starting from the observation that the reduced state of a system strongly coupled to a bath is, in general, an athermal state, we introduce and study a cyclic battery–charger quantum device that is in thermal equilibrium, or in a ground state, during the charge storing stage. The cycle has four stages: the equilibrium storage stage is interrupted by disconnecting the battery from the charger, then work is extracted from the battery, and then the battery is reconnected with the charger; finally, the system is brought back to equilibrium. At no point during the cycle are the battery–charger correlations artificially erased. We study the case where the battery and charger together comprise a spin-1/2 Ising chain, and show that the main characteristics—the extracted energy and the thermodynamic efficiency—can be enhanced by operating the cycle close to the quantum phase transition point. When the battery is just a single spin, we find that the output work and efficiency show a scaling behavior at criticality and derive the corresponding critical exponents. Due to always present correlations between the battery and the charger, operations that are equivalent from the perspective of the battery can entail different energetic costs for switching the battery–charger coupling. This happens only when the coupling term does not commute with the battery’s bare Hamiltonian, and we use this purely quantum leverage to further optimize the performance of the device.

arXiv:2110.10600•New Journal of Physics•Dec 16, 2021•0 citations

Quantum batteries at the verge of a phase transition

Felipe Barra, Karen V. Hovhannisyan, Alberto Imparato

Starting from the observation that the reduced state of a system strongly coupled to a bath is, in general, an athermal state, we introduce and study a cyclic battery-charger quantum device that is in thermal equilibrium, or in a ground state, during the charge storing stage. The cycle has four stages: the equilibrium storage stage is interrupted by disconnecting the battery from the charger, then work is extracted from the battery, and then the battery is reconnected with the charger; finally, the system is brought back to equilibrium. At no point during the cycle are the battery-charger correlations artificially erased. We study the case where the battery and charger together comprise a spin-1/2 Ising chain, and show that the main characteristics-the extracted energy and the thermodynamic efficiency-can be enhanced by operating the cycle close to the quantum phase transition point. When the battery is just a single spin, we find that the output work and efficiency show a scaling behavior at criticality and derive the corresponding critical exponents. Due to always present correlations between the battery and the charger, operations that are equivalent from the perspective of the battery can entail different energetic costs for switching the battery-charger coupling. This happens only when the coupling term does not commute with the battery's bare Hamiltonian, and we use this purely quantum leverage to further optimize the performance of the device.

•Jan 1, 2022•61 citations

Daemonic ergotropy in continuously monitored open quantum batteries

Daniele Morrone, Matteo A. C. Rossi, Marco G. Genoni

The amount of work that can be extracted from a quantum system can be increased by exploiting the information obtained from a measurement performed on a correlated ancillary system. The concept of daemonic ergotropy has been introduced to properly describe and quantify this work extraction enhancement in the quantum regime. We here explore the application of this idea in the context of continuously monitored open quantum systems, where information is gained by measuring the environment interacting with the energy-storing quantum device. We first show that the corresponding daemonic ergotropy takes values between the ergotropy and the energy of the corresponding unconditional state. The upper bound is achieved by assuming an initial pure state and a perfectly efficient projective measurement on the environment, independently of the kind of measurement performed. On the other hand, if the measurement is inefficient or the initial state is mixed, the daemonic ergotropy is generally dependent on the measurement strategy. This scenario is investigated via a paradigmatic example of an open quantum battery: a two-level atom driven by a classical field and whose spontaneously emitted photons are continuously monitored via either homodyne, heterodyne, or photodetection.

arXiv:2302.12279•Physical Review Applied•Oct 27, 2023•39 citations

Bridging the daemonic gap en route to charge multi-mode batteries via a single auxiliary

Chandrima B. Pushpan, Amit Kumar Pal

We show that harnessing daemonic advantage is possible while charging a quantum battery by first time-evolving the battery collectively with an auxiliary charger, followed by an energy extraction via tracing out the charger. We define the difference between the minimum daemonic ergotropy and the maximum ergotropy of the battery as the daemonic gap at the time where the ergotropy of the battery is maximum. Considering a harmonic mode as the battery and a qubit as the auxiliary charger interacting via Jaynes-Cummings interaction, we show that the daemonic gap can be closed for specific initial passive states of the battery, including the ground state, truncated mixtures of low-lying states, and canonical thermal states. We further define the daemonic band as the difference between the maximum and the minimum daemonic ergotropy, and show that starting from the ground state of the single-mode battery, the daemonic band collapses. We also show that achieving a complete charging, along with accessing the full daemonic band, is possible for the single-mode battery using all of the other initial states by repeating the charging cycle and maximizing ergotropy in every round. We extend the battery-charger design to a multi-mode resonator battery and a qudit charger, and demonstrate, for a double-mode battery and a qutrit charger, that repeating the charging cycle is vital for simultaneously charging individual modes of the collective battery.

quant-pharXiv:2511.07243•Nov 11, 2025•0 citations

Cyclic solid-state quantum battery: thermodynamic characterization and quantum hardware simulation

Luca Razzoli, Giulia Gemme, Ilia Khomchenko +4 more

Abstract We introduce a cyclic quantum battery QB model, based on an interacting bipartite system, weakly coupled to a thermal bath. The working cycle of the battery consists of four strokes: system thermalization, disconnection of subsystems, ergotropy extraction, and reconnection. The thermal bath acts as a charger in the thermalization stroke, while ergotropy extraction is possible because the ensuing thermal state is no longer passive after the disconnection stroke. Focusing on the case of two interacting qubits, we show that phase coherence, in the presence of non-trivial correlations between the qubits, can be exploited to reach working regimes with efficiency higher than 50% while providing finite ergotropy. Our protocol is illustrated through a simple and feasible circuit model of a cyclic superconducting QB. Furthermore, we simulate the considered cycle on superconducting IBM quantum machines. The good agreement between the theoretical and simulated results strongly suggests that our scheme for cyclic QBs can be successfully realized in superconducting quantum hardware.

arXiv:2407.07157•Quantum Science and Technology•Dec 13, 2024•29 citations

Activating thermally charged quantum batteries in finite time: Thermodynamic trade-offs between correlations, work, and information

Bhaskar Barman, Janine Splettstoesser, Henning Kirchberg

Thermally charged quantum batteries provide a stable and easy-to-have energy resource, but remain passive and therefore do not allow useful energy extraction on demand via unitary operations. We introduce a time-dependent stirring protocol that activates a thermally charged quantum battery through a time-dependent coupling to an auxiliary activator, thereby generating correlations that drive the battery into an active state. Accounting explicitly for the energetic cost of the stirring process, the entropic cost of correlation generation and the activation time, we derive bounds on the maximal net extractable energy. Incorporating projective measurement on the activator and exploiting the information gained through the measurement further enhances the extractable energy. As an experimentally relevant example, we analyze a waveguide-QED setup where a harmonic-oscillator battery (waveguide) is stirred and monitored by a two-level system. We characterize the performance of the protocol in terms of net extractable energy (net ergotropy) and power output.

quant-pharXiv:2607.12573•Jul 15, 2026•0 citations
Abstract The reduced state of a small system strongly coupled to a charger in thermal equilibrium may be athermal and used as a small battery once disconnected. By harnessing the battery-charger correlations, the battery’s extractable energy can increase above the ergotropy. We introduce a protocol that uses a quantum system as a memory that measures the charger and leaves the battery intact in its charged state. Using the information gained from the measurement, the daemonic ergotropy of the battery is extracted. Then the battery is reconnected to the charger, thermalizing and charging it. However, the memory should return to its initial standard state to close the thermodynamic cycle. Thus, on the one hand, the work cost of the cycle is the sum of the disconnecting and reconnecting battery-charger work plus the measurement and erasure work. On the other hand, the extracted energy is the daemonic ergotropy of the battery plus the ergotropy of the memory. The ratio of these quantities defines the efficiency of the cycle. The protocol is exemplified by a modified transverse spin 1/2 Ising chain, one spin functioning as the battery and the others as the charger. The memory is another auxiliary spin 1/2. We found pairs of measurement schemes from which we extract the same daemonic ergotropy from the battery, they dissipate the same amount of energy, and one leaves the memory in an active state, the other in a passive state. We study the memory’s ergotropy and the daemonic ergotropy of the battery. We find that with measurements, the efficiency can surpass that of the unmeasured protocol, given conditions on temperature, coupling, and choice of the measurement operators.
Abstract Starting from the observation that the reduced state of a system strongly coupled to a bath is, in general, an athermal state, we introduce and study a cyclic battery–charger quantum device that is in thermal equilibrium, or in a ground state, during the charge storing stage. The cycle has four stages: the equilibrium storage stage is interrupted by disconnecting the battery from the charger, then work is extracted from the battery, and then the battery is reconnected with the charger; finally, the system is brought back to equilibrium. At no point during the cycle are the battery–charger correlations artificially erased. We study the case where the battery and charger together comprise a spin-1/2 Ising chain, and show that the main characteristics—the extracted energy and the thermodynamic efficiency—can be enhanced by operating the cycle close to the quantum phase transition point. When the battery is just a single spin, we find that the output work and efficiency show a scaling behavior at criticality and derive the corresponding critical exponents. Due to always present correlations between the battery and the charger, operations that are equivalent from the perspective of the battery can entail different energetic costs for switching the battery–charger coupling. This happens only when the coupling term does not commute with the battery’s bare Hamiltonian, and we use this purely quantum leverage to further optimize the performance of the device.
Starting from the observation that the reduced state of a system strongly coupled to a bath is, in general, an athermal state, we introduce and study a cyclic battery-charger quantum device that is in thermal equilibrium, or in a ground state, during the charge storing stage. The cycle has four stages: the equilibrium storage stage is interrupted by disconnecting the battery from the charger, then work is extracted from the battery, and then the battery is reconnected with the charger; finally, the system is brought back to equilibrium. At no point during the cycle are the battery-charger correlations artificially erased. We study the case where the battery and charger together comprise a spin-1/2 Ising chain, and show that the main characteristics-the extracted energy and the thermodynamic efficiency-can be enhanced by operating the cycle close to the quantum phase transition point. When the battery is just a single spin, we find that the output work and efficiency show a scaling behavior at criticality and derive the corresponding critical exponents. Due to always present correlations between the battery and the charger, operations that are equivalent from the perspective of the battery can entail different energetic costs for switching the battery-charger coupling. This happens only when the coupling term does not commute with the battery's bare Hamiltonian, and we use this purely quantum leverage to further optimize the performance of the device.
The amount of work that can be extracted from a quantum system can be increased by exploiting the information obtained from a measurement performed on a correlated ancillary system. The concept of daemonic ergotropy has been introduced to properly describe and quantify this work extraction enhancement in the quantum regime. We here explore the application of this idea in the context of continuously monitored open quantum systems, where information is gained by measuring the environment interacting with the energy-storing quantum device. We first show that the corresponding daemonic ergotropy takes values between the ergotropy and the energy of the corresponding unconditional state. The upper bound is achieved by assuming an initial pure state and a perfectly efficient projective measurement on the environment, independently of the kind of measurement performed. On the other hand, if the measurement is inefficient or the initial state is mixed, the daemonic ergotropy is generally dependent on the measurement strategy. This scenario is investigated via a paradigmatic example of an open quantum battery: a two-level atom driven by a classical field and whose spontaneously emitted photons are continuously monitored via either homodyne, heterodyne, or photodetection.
We show that harnessing daemonic advantage is possible while charging a quantum battery by first time-evolving the battery collectively with an auxiliary charger, followed by an energy extraction via tracing out the charger. We define the difference between the minimum daemonic ergotropy and the maximum ergotropy of the battery as the daemonic gap at the time where the ergotropy of the battery is maximum. Considering a harmonic mode as the battery and a qubit as the auxiliary charger interacting via Jaynes-Cummings interaction, we show that the daemonic gap can be closed for specific initial passive states of the battery, including the ground state, truncated mixtures of low-lying states, and canonical thermal states. We further define the daemonic band as the difference between the maximum and the minimum daemonic ergotropy, and show that starting from the ground state of the single-mode battery, the daemonic band collapses. We also show that achieving a complete charging, along with accessing the full daemonic band, is possible for the single-mode battery using all of the other initial states by repeating the charging cycle and maximizing ergotropy in every round. We extend the battery-charger design to a multi-mode resonator battery and a qudit charger, and demonstrate, for a double-mode battery and a qutrit charger, that repeating the charging cycle is vital for simultaneously charging individual modes of the collective battery.
Abstract We introduce a cyclic quantum battery QB model, based on an interacting bipartite system, weakly coupled to a thermal bath. The working cycle of the battery consists of four strokes: system thermalization, disconnection of subsystems, ergotropy extraction, and reconnection. The thermal bath acts as a charger in the thermalization stroke, while ergotropy extraction is possible because the ensuing thermal state is no longer passive after the disconnection stroke. Focusing on the case of two interacting qubits, we show that phase coherence, in the presence of non-trivial correlations between the qubits, can be exploited to reach working regimes with efficiency higher than 50% while providing finite ergotropy. Our protocol is illustrated through a simple and feasible circuit model of a cyclic superconducting QB. Furthermore, we simulate the considered cycle on superconducting IBM quantum machines. The good agreement between the theoretical and simulated results strongly suggests that our scheme for cyclic QBs can be successfully realized in superconducting quantum hardware.
Thermally charged quantum batteries provide a stable and easy-to-have energy resource, but remain passive and therefore do not allow useful energy extraction on demand via unitary operations. We introduce a time-dependent stirring protocol that activates a thermally charged quantum battery through a time-dependent coupling to an auxiliary activator, thereby generating correlations that drive the battery into an active state. Accounting explicitly for the energetic cost of the stirring process, the entropic cost of correlation generation and the activation time, we derive bounds on the maximal net extractable energy. Incorporating projective measurement on the activator and exploiting the information gained through the measurement further enhances the extractable energy. As an experimentally relevant example, we analyze a waveguide-QED setup where a harmonic-oscillator battery (waveguide) is stirred and monitored by a two-level system. We characterize the performance of the protocol in terms of net extractable energy (net ergotropy) and power output.