The effect of niobium thin film structure on losses in superconducting circuits
Maxwell Drimmer, Sjoerd Telkamp, Felix L. Fischer, Ines Corveira Rodrigues, Clemens Todt, Filip Křížek, Dominik Kriegner, Müller, Christoph, W. Wegscheider, Yiwen Chu
The performance of superconducting microwave circuits is strongly influenced by the material properties of the superconducting film and substrate. While progress has been made in understanding the importance of surface preparation and the effect of surface oxides, the complex effect of superconductor film structure on microwave losses is not yet fully understood. In this study, we investigate the microwave properties of niobium resonators with different crystalline properties and related surface topographies. We analyze a series of magnetron sputtered films in which the Nb crystal orientation and surface topography are changed by varying the substrate temperatures between room temperature and 975 K. The lowest-loss resonators that we measure have quality factors of over one million at single-photon powers, among the best ever recorded using the Nb on sapphire platform. We observe the highest quality factors in films grown at an intermediate temperature regime of the growth series (550 K) where the films display both preferential ordering of the crystal domains and low surface roughness. Furthermore, we analyze the temperature-dependent behavior of our resonators to learn about how the quasiparticle density in the Nb film is affected by the niobium crystal structure and the presence of grain boundaries. Our results stress the connection between the crystal structure of superconducting films and the loss mechanisms suffered by the resonators and demonstrate that even a moderate change in temperature during thin film deposition can significantly affect the resulting quality factors.
The performance of superconducting microwave circuits is strongly influenced by the material properties of the superconducting film and substrate. While progress has been made in understanding the importance of surface preparation and the effect of surface oxides, the complex effect of superconductor film structure on microwave losses is not yet fully understood. In this study, we investigate the microwave properties of niobium resonators with different crystalline properties and related surface topographies. We analyze a series of magnetron sputtered films in which the Nb crystal orientation and surface topography are changed by varying the substrate temperatures between room temperature and 975 K. The lowest-loss resonators that we measure have quality factors of over one million at single-photon powers, among the best ever recorded using the Nb on sapphire platform. We observe the highest quality factors in films grown at an intermediate temperature regime of the growth series (550 K) where the films display both preferential ordering of the crystal domains and low surface roughness. Furthermore, we analyze the temperature-dependent behavior of our resonators to learn about how the quasiparticle density in the Nb film is affected by the niobium crystal structure and the presence of grain boundaries. Our results stress the connection between the crystal structure of superconducting films and the loss mechanisms suffered by the resonators and demonstrate that even a moderate change in temperature during thin film deposition can significantly affect the resulting quality factors.
Abstract The performance of superconducting microwave circuits is strongly influenced by the material properties of the superconducting film and substrate. While progress has been made in understanding the importance of surface preparation and the effect of surface oxides, the complex effect of superconductor film structure on microwave losses is not yet fully understood. In this study, we investigate the microwave properties of niobium resonators with different crystalline properties and related surface topographies. We analyze a series of magnetron sputtered films in which the Nb crystal orientation and surface topography are changed by varying the substrate temperatures between room temperature and 975 K. The lowest-loss resonators that we measure have quality factors of over 10 6 at single-photon powers, among the best ever recorded using the Nb on sapphire platform. We observe the highest quality factors in films grown at an intermediate temperature regime of the growth series (550 K) where the films display both preferential ordering of the crystal domains and low surface roughness. Furthermore, we analyze the temperature-dependent behavior of our resonators to learn about how the quasiparticle density in the Nb film is affected by the niobium crystal structure and the presence of grain boundaries. Our results stress the connection between the crystal structure of superconducting films and the loss mechanisms suffered by the resonators and indicate that even a moderate change in temperature during thin film deposition can significantly affect the resulting quality factors.
The performance of superconducting microwave circuits is strongly influenced by the material properties of the superconducting film and substrate. While progress has been made in understanding the importance of surface preparation and the effect of surface oxides, the complex effect of superconductor film structure on microwave losses is not yet fully understood. In this study, we investigate the microwave properties of niobium resonators with different crystalline properties and related surface topographies. We analyze a series of magnetron sputtered films in which the Nb crystal orientation and surface topography are changed by varying the substrate temperatures between room temperature and 975K. The lowest-loss resonators that we measure have quality factors of over 106 at single-photon powers, among the best ever recorded using the Nb on sapphire platform. We observe the highest quality factors in films grown at an intermediate temperature regime of the growth series (550K) where the films display both preferential ordering of the crystal domains and low surface roughness. Furthermore, we analyze the temperature-dependent behavior of our resonators to learn about how the quasiparticle density in the Nb film is affected by the niobium crystal structure and the presence of grain boundaries. Our results stress the connection between the crystal structure of superconducting films and the loss mechanisms suffered by the resonators and indicate that even a moderate change in temperature during thin film deposition can significantly affect the resulting quality factors.
Quantum coherence in superconducting circuits has increased steadily over the last decades as a result of a growing understanding of the various loss mechanisms. Recently, tantalum (Ta) emerged as a promising material to address microscopic sources of loss found on niobium (Nb) or aluminum (Al) surfaces. However, the effects of film and interface microstructure on low-temperature microwave loss are still not well understood. Here we present a systematic study of the structural and electrical properties of Ta and Nb films sputtered on c-plane sapphire at varying growth temperatures. As growth temperature is increased, our results show that the onset of epitaxial growth of alpha-phase Ta correlates with lower Ta surface roughness, higher critical temperature, and higher residual resistivity ratio, but surprisingly also correlates with a significant increase in loss at microwave frequency. Notably, this high level of loss is not observed in Nb films prepared in the same way and having very similar structure. By experimentally controlling the surface on which the Ta film is nucleated, we determine that the source of loss is only present in samples having an epitaxial Ta/sapphire interface and show that it is apparently mitigated by either growing a thin, epitaxial Nb inter-layer between the Ta film and the substrate or by intentionally treating, and effectively damaging, the sapphire surface with an in-situ argon plasma before Ta growth. In addition to elucidating this interfacial microwave loss, this work provides adequate process details to aid reproducible growth of low-loss Ta films across fabrication facilities.
Titanium nitride is an attractive material for a range of superconducting quantum-circuit applications owing to its low microwave losses, high surface inductance, and chemical stability. The physical properties and device performance, nevertheless, depend strongly on the quality of the materials. In this paper, we focus on the highly crystalline and epitaxial titanium nitride thin films deposited on sapphire substrates using magnetron sputtering at an intermediate temperature (${300}^{\ensuremath{\circ}}\mathrm{C}$). We performed a set of systematic and comprehensive material characterizations to thoroughly understand the structural, chemical, and transport properties. Microwave losses at low temperatures were studied using patterned microwave resonators, where the best internal quality factor in the single-photon regime is measured to be $3.3\ifmmode\times\else\texttimes\fi{}{10}^{6}$ and that in the high-power regime $>1.0\ifmmode\times\else\texttimes\fi{}{10}^{7}$. Adjusted with the material filling factor of the resonators, the microwave loss-tangent here compares well with the previously reported best values for superconducting resonators. This work lays the foundation of using epitaxial titanium nitride for low-loss superconducting quantum circuits.
Understanding the correlation between material properties and microwave losses in superconducting films is a crucial subject for developing low-loss materials for quantum circuits. We focus on vanadium (V) as a novel material for superconducting quantum devices and discuss loss in V films in relation to their structural properties. Using a sputtering method, we grow four V-film structures on (001)-oriented Si wafers, employing Nb and Ta as the buffer and capping layer materials, respectively: Nb/V/Ta, Nb/V, V/Ta, and V. X-ray diffraction and atomic force microscopy reveal that the V films grown on the Nb buffer layers have higher uniformity of lattice orientation and smaller grain size than that directly grown on the Si wafer. Coplanar waveguide resonators are fabricated from the four V-film structures, and averaged photon number (⟨nph⟩) dependences of internal quality factor (Qint) are obtained by performing microwave measurements. By analyzing the obtained Qint vs ⟨nph⟩, it is found that loss at the V surface is dominated by ⟨nph⟩-independent non-two-level-system (non-TLS) losses, which can be mitigated by introducing the Ta capping layer. Furthermore, the V films on the Nb buffer layers exhibit lower Qint in the ⟨nph⟩ range from 100 to 106 and higher non-TLS loss than that directly grown on Si wafers, even though the former has higher lattice-orientation uniformity than the latter. Origins of these trends might be relevant to V oxides, of which presence at surfaces and grain boundaries in bulk regions in the V resonators is suggested by energy dispersive X-ray spectroscopy and X-ray photoelectron spectroscopy, and/or V hydrides.
Niobium films typically constitute a significant component in the construction of modern two-dimensional superconducting qubit architectures, yet their contribution to the total decay rate is not fully understood, making it difficult to definitively identify dominant loss channels in present designs. We present the first study, which correlates direct measurements of RF losses in such films to material parameters by investigating a high-power impulse magnetron sputtered (HiPIMS) film atop a three-dimensional niobium superconducting radiofrequency (SRF) resonator. Our findings indicate that microwave dissipation in the HiPIMS-prepared niobium films, within the quantum regime, resembles that of record-high intrinsic quality factor of bulk niobium SRF cavities, with lifetimes extending into seconds. Microstructure and impurity level of the niobium film do not significantly affect the losses. These results set the scale of microwave losses in niobium films and show that niobium losses do not dominate the observed coherence times in present two-dimensional superconducting qubit designs, instead highlighting the role of the dielectric oxide in limiting the performance.