Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2311.02942 · EPJ Quantum Technology

Improvement of response bandwidth and sensitivity of Rydberg receiver using multi-channel excitations

Jinlian Hu, Yuechun Jiao, Yunhui He, Teyan Chen, Xiongbin Yu, Hao Zhang, Linjie Zhang, Jianming Zhao, Suotang Jia

Published Nov 28, 2023• 33 citations
arXivHTMLPDF

Abstract

Abstract We investigate the response bandwidth of a superheterodyne Rydberg receiver at a room-temperature vapor cell, and present an architecture of atomic array to increase the response bandwidth. Two microwave fields, denoted as a local oscillator (LO) ELO and a signal field ESig, couple two Rydberg states transition of |52D5/2⟩ → |53P3/2⟩. In the presence of the LO field, the frequency difference between two fields can be read out as an intermediate frequency (IF) signal using Rydberg electromagnetically induced transparency (EIT) spectroscopy. The bandwidth of the Rydberg receiver is obtained by measuring the output power of IF signal versus the frequency difference between two fields. The bandwidth dependence on the Rabi frequency of excitation lasers is presented, which shows the bandwidth decrease with the Rabi frequency of probe laser, while it is quadratic dependence on the Rabi frequency of coupling laser. Meanwhile, we investigate the effect of probe laser waist on the bandwidth, showing that the bandwidth is inversely proportional to the laser waist. We achieve a maximum response bandwidth of the receiver about 6.8~MHz. Finally, we design an architecture of atomic array for increasing the response and keeping the sensitivity, simultaneously. Our work has the potential to extend the applications of Rydberg atoms in communications.

DOI
10.1140/epjqt/s40507-023-00209-7

Related papers

Sensitivity enhancement in Rydberg atomic microwave superheterodyne measurements through laser-atom-microwave interaction mechanisms

Zhongzhou Tian, Guojin Zeng, Chao Yan +3 more

Measurement sensitivity is crucial for the practical application of Rydberg atomic microwave superheterodyne receiver systems in communication, radar, and navigation. Based on laser-atom-microwave interaction mechanisms, the influence of laser powers and local-oscillator (LO) microwave field intensity on measurement sensitivity is systematically studied in this paper. Measurement sensitivity is analyzed through electromagnetically induced transparency (EIT) spectral characteristics, specifically EIT amplitude and full-width-half-maximum (FWHM),larger amplitudes and narrower FWHM indicate improved signal-to-noise ratios. For a 60D-state Rydberg atomic system with fixed probe and coupling laser beam waists (800 µm and 875 µm), optimal parameters are determined: probe laser power of 60 µW(Rabi frequency: 2π×7.02 MHz), coupling laser power of 40 mW (Rabi frequency: 2π×0.66 MHz), and LO microwave Rabi frequency of 2π×8.34 MHz. Experimental results demonstrate a 4.6 dB sensitivity enhancement, advancing from −137.5dBm/Hz to −142.1 dBm/Hz at 3.21 GHz microwave field. This improvement is attributed to precise alignment of laser-atom and microwave-atom interactions, bridging the gap toward quantum sensitivity limits.

Applied Optics and Photonics China (AOPC)•Oct 28, 2025•0 citations

Instantaneous Bandwidth Enhancement Measurement of Rydberg Atoms Based on Laser Rabi Frequency

Qimeng Wang, Qiang An, Yunqi Fu

Improving the bandwidth of Rydberg atom-based receivers is an ongoing challenge because of the long-lived Rydberg state lifetimes that limit the refresh rate of ground-state atoms. In particular, the local oscillator (LO)-based Rydberg mixer approach allows for bandwidths in a few MHz ranges. Here, we use the laser parameters of the Rydberg atomic receiver superheterodyne detection technology to study their respective bandwidths. We have confirmed through experiments that laser power and waist diameter can affect the Rabi frequency and thus alter the instantaneous bandwidth. The experimental results indicate that the instantaneous bandwidth is directly proportional to the Rabi frequency of the coupled light and inversely proportional to the Rabi frequency of the probe light. Optimal parameters for quantum sensing applications are identified through powerdependent Rabi oscillation measurements.

International Conference on Microwave and Millimeter Wave Technology (ICMMT)•May 19, 2025•0 citations

Probing bandwidth and sensitivity in Rydberg atom sensing via optical homodyne and rf heterodyne detection

Dixith Manchaiah, Stone Oliver, Samuel Berweger +2 more

Rydberg atom based sensors allow for SI traceable measurements and show promise for applications in the field of communication and radar technologies. In this article, we investigate the bandwidth and sensitivity of a Rydberg atom-based sensor in a rubidium vapor cell using Rydberg electromagnetically induced transparency (EIT) spectroscopy. We employ a radio-frequency (RF) heterodyne measurement technique in combination with an optical homodyne setup to extend the achievable range between sensitivity and bandwidth in a Rydberg sensor. While the bandwidth of Rydberg sensors are limited by the transit time of atoms and the Rabi frequency of the coupling field, achieving higher bandwidth through smaller beam sizes is thought to compromise sensitivity due to reduced EIT signal strength. Using optical homodyne detection, we demonstrate that sensitivity is preserved while achieving a response bandwidth of 8 MHz. In addition, using the Rydberg sensor, we receive digital communication signals and present error vector magnitude (EVM) measurements as a function of varying symbol rates and bandwidth of the Rydberg sensor. Furthermore, the sensor's performance is compared with a conventional RF mixer. We establish that the bandwidth of a Rydberg sensor when receiving a pure tone is not the same as the bandwidth of the sensor when receiving a modulated signal. This difference results from the spreading of symbols in the frequency domain, leading to a reduction of the signal to noise ratio (SNR) and an accumulation of noise over the total span of the modulated signal.

arXiv:2509.20632•Physical Review A•Dec 22, 2025•5 citations

A Cs Rydberg Atomic Microwave Oscillator for Electric Field Sensing

He Wang, David Rosser, Michael J. Mazon +1 more

In this paper, we report an atomic oscillator in Ku band and its application for electric field (E-field) sensing with Cs Rydberg atoms in a room-temperature vapor cell. The oscillator is associated with the Cs Rydberg transition of 362D5/2– 372P3/2at 16.316 GHz which is generated with a two-laser double-resonance excitation. We characterized the energetics and the dipole moment of the Rydberg transition and used Electromagnetically Induced Transparency (EIT) and Autler-Townes (AT) effects for detecting continuous and amplitude/frequency modulated microwave E-fields. To enhance the oscillator’s response to weak signals, a superheterodyne technique was incorporated into the Rydberg oscillator system, which resulted in an improvement in the oscillator’s sensitivity by 100 times. Furthermore, our modeling shows that the Cs Rydberg atomic oscillator can be tuned to broad frequency ranges from MHz to THz for various RF applications.

Joint Conference of the European Frequency and Time Forum and IEEE International Frequency Control Symposium (EFTF/IFCS)•May 15, 2023•1 citation

Sensitivity improvement of Rydberg atom-based microwave sensing via electromagnetically induced transparency

M. H. Cai, Zi-Shan Xu, Shuhang You +1 more

A highly excited Rydberg atom via electromagnetically induced transparency with two color cascading lasers has extreme sensitivity to electric fields of microwave ranging from 100 MHz to over 1 THz. It can be used as susceptible atom-based microwave communication antennas where the carrier wave usually works exactly resonant to the transition between a pair of adjacent Rydberg states with large electric dipole moment. A technique of superheterodyne with a strong on-resonant local microwave oscillator is employed to induce considerable Autler-Townes splitting where the antennas has a highest dynamic response to another weak target signal microwave carrier. To further improve the sensitivity of atomic antenna in communication, we detune the carrier microwave frequency off resonance forming an asymmetrically optical splitting and fix the coupling laser frequency at the shoulder of the stronger one, and optimize the local field strength simultaneously. It gives a sensitivity of 12.50(04) $\rm{nVcm^{-1}\cdot Hz^{-1/2}}$. Its enhancement mechanism of sensitivity is also proved by a theoretical simulation.

arXiv:2111.06582•Nov 12, 2021•1 citation

Doppler-enhanced superheterodyne Rydberg microwave receiver

Yuwen Yin, Ruimin Chen, Shibing Ji +7 more

We report the enhanced sensitivity of the Rydberg microwave (MW) receiver by exploiting the Doppler effect in a vapor cell. A two-photon Rydberg ladder scheme is implemented via the co-propagation of probe and coupling lasers, which enhances the Doppler effect. When an MW field is applied, microwave dressing modifies the velocity-dependent resonance condition, enabling stronger contributions from atoms with non-zero velocities and leading to an enhancement of the EIT transmission. Based on this mechanism, we achieve a sensitivity of $35.1\ \mathrm{nV\ cm^{-1}\ Hz^{-1/2}}$ using the heterodyne technique, which is 1.5 times better than that obtained in the counter-propagating configuration. Meanwhile, the required local oscillator (LO) field is reduced by a factor of 17.6 compared with the counter-propagating configuration, which is advantageous for applications requiring minimal radiation and low power consumption. Moreover, the co-propagating configuration is more amenable to integration or portable sensing platforms because multiple laser fields can be delivered through a single optical fiber.

physics.atom-phCross-listedarXiv:2606.24247•Applied Physics Letters•Jun 24, 2026•0 citations
Abstract We investigate the response bandwidth of a superheterodyne Rydberg receiver at a room-temperature vapor cell, and present an architecture of atomic array to increase the response bandwidth. Two microwave fields, denoted as a local oscillator (LO) ELO and a signal field ESig, couple two Rydberg states transition of |52D5/2⟩ → |53P3/2⟩. In the presence of the LO field, the frequency difference between two fields can be read out as an intermediate frequency (IF) signal using Rydberg electromagnetically induced transparency (EIT) spectroscopy. The bandwidth of the Rydberg receiver is obtained by measuring the output power of IF signal versus the frequency difference between two fields. The bandwidth dependence on the Rabi frequency of excitation lasers is presented, which shows the bandwidth decrease with the Rabi frequency of probe laser, while it is quadratic dependence on the Rabi frequency of coupling laser. Meanwhile, we investigate the effect of probe laser waist on the bandwidth, showing that the bandwidth is inversely proportional to the laser waist. We achieve a maximum response bandwidth of the receiver about 6.8~MHz. Finally, we design an architecture of atomic array for increasing the response and keeping the sensitivity, simultaneously. Our work has the potential to extend the applications of Rydberg atoms in communications.
Measurement sensitivity is crucial for the practical application of Rydberg atomic microwave superheterodyne receiver systems in communication, radar, and navigation. Based on laser-atom-microwave interaction mechanisms, the influence of laser powers and local-oscillator (LO) microwave field intensity on measurement sensitivity is systematically studied in this paper. Measurement sensitivity is analyzed through electromagnetically induced transparency (EIT) spectral characteristics, specifically EIT amplitude and full-width-half-maximum (FWHM),larger amplitudes and narrower FWHM indicate improved signal-to-noise ratios. For a 60D-state Rydberg atomic system with fixed probe and coupling laser beam waists (800 µm and 875 µm), optimal parameters are determined: probe laser power of 60 µW(Rabi frequency: 2π×7.02 MHz), coupling laser power of 40 mW (Rabi frequency: 2π×0.66 MHz), and LO microwave Rabi frequency of 2π×8.34 MHz. Experimental results demonstrate a 4.6 dB sensitivity enhancement, advancing from −137.5dBm/Hz to −142.1 dBm/Hz at 3.21 GHz microwave field. This improvement is attributed to precise alignment of laser-atom and microwave-atom interactions, bridging the gap toward quantum sensitivity limits.
Improving the bandwidth of Rydberg atom-based receivers is an ongoing challenge because of the long-lived Rydberg state lifetimes that limit the refresh rate of ground-state atoms. In particular, the local oscillator (LO)-based Rydberg mixer approach allows for bandwidths in a few MHz ranges. Here, we use the laser parameters of the Rydberg atomic receiver superheterodyne detection technology to study their respective bandwidths. We have confirmed through experiments that laser power and waist diameter can affect the Rabi frequency and thus alter the instantaneous bandwidth. The experimental results indicate that the instantaneous bandwidth is directly proportional to the Rabi frequency of the coupled light and inversely proportional to the Rabi frequency of the probe light. Optimal parameters for quantum sensing applications are identified through powerdependent Rabi oscillation measurements.
Rydberg atom based sensors allow for SI traceable measurements and show promise for applications in the field of communication and radar technologies. In this article, we investigate the bandwidth and sensitivity of a Rydberg atom-based sensor in a rubidium vapor cell using Rydberg electromagnetically induced transparency (EIT) spectroscopy. We employ a radio-frequency (RF) heterodyne measurement technique in combination with an optical homodyne setup to extend the achievable range between sensitivity and bandwidth in a Rydberg sensor. While the bandwidth of Rydberg sensors are limited by the transit time of atoms and the Rabi frequency of the coupling field, achieving higher bandwidth through smaller beam sizes is thought to compromise sensitivity due to reduced EIT signal strength. Using optical homodyne detection, we demonstrate that sensitivity is preserved while achieving a response bandwidth of 8 MHz. In addition, using the Rydberg sensor, we receive digital communication signals and present error vector magnitude (EVM) measurements as a function of varying symbol rates and bandwidth of the Rydberg sensor. Furthermore, the sensor's performance is compared with a conventional RF mixer. We establish that the bandwidth of a Rydberg sensor when receiving a pure tone is not the same as the bandwidth of the sensor when receiving a modulated signal. This difference results from the spreading of symbols in the frequency domain, leading to a reduction of the signal to noise ratio (SNR) and an accumulation of noise over the total span of the modulated signal.
In this paper, we report an atomic oscillator in Ku band and its application for electric field (E-field) sensing with Cs Rydberg atoms in a room-temperature vapor cell. The oscillator is associated with the Cs Rydberg transition of 362D5/2– 372P3/2at 16.316 GHz which is generated with a two-laser double-resonance excitation. We characterized the energetics and the dipole moment of the Rydberg transition and used Electromagnetically Induced Transparency (EIT) and Autler-Townes (AT) effects for detecting continuous and amplitude/frequency modulated microwave E-fields. To enhance the oscillator’s response to weak signals, a superheterodyne technique was incorporated into the Rydberg oscillator system, which resulted in an improvement in the oscillator’s sensitivity by 100 times. Furthermore, our modeling shows that the Cs Rydberg atomic oscillator can be tuned to broad frequency ranges from MHz to THz for various RF applications.
A highly excited Rydberg atom via electromagnetically induced transparency with two color cascading lasers has extreme sensitivity to electric fields of microwave ranging from 100 MHz to over 1 THz. It can be used as susceptible atom-based microwave communication antennas where the carrier wave usually works exactly resonant to the transition between a pair of adjacent Rydberg states with large electric dipole moment. A technique of superheterodyne with a strong on-resonant local microwave oscillator is employed to induce considerable Autler-Townes splitting where the antennas has a highest dynamic response to another weak target signal microwave carrier. To further improve the sensitivity of atomic antenna in communication, we detune the carrier microwave frequency off resonance forming an asymmetrically optical splitting and fix the coupling laser frequency at the shoulder of the stronger one, and optimize the local field strength simultaneously. It gives a sensitivity of 12.50(04) nVcm−1⋅Hz−1/2\rm{nVcm^{-1}\cdot Hz^{-1/2}}nVcm−1⋅Hz−1/2. Its enhancement mechanism of sensitivity is also proved by a theoretical simulation.
We report the enhanced sensitivity of the Rydberg microwave (MW) receiver by exploiting the Doppler effect in a vapor cell. A two-photon Rydberg ladder scheme is implemented via the co-propagation of probe and coupling lasers, which enhances the Doppler effect. When an MW field is applied, microwave dressing modifies the velocity-dependent resonance condition, enabling stronger contributions from atoms with non-zero velocities and leading to an enhancement of the EIT transmission. Based on this mechanism, we achieve a sensitivity of 35.1 nV cm−1 Hz−1/235.1\ \mathrm{nV\ cm^{-1}\ Hz^{-1/2}}35.1 nV cm−1 Hz−1/2 using the heterodyne technique, which is 1.5 times better than that obtained in the counter-propagating configuration. Meanwhile, the required local oscillator (LO) field is reduced by a factor of 17.6 compared with the counter-propagating configuration, which is advantageous for applications requiring minimal radiation and low power consumption. Moreover, the co-propagating configuration is more amenable to integration or portable sensing platforms because multiple laser fields can be delivered through a single optical fiber.