© 2026 Aqora Quantum S.A.S.

Terms Privacy Legal Notice

arXiv:2208.12784 · Physical Review Applied

Stimulated Laser Cooling in a Compact Geometry Using Microfabricated Atomic Beam Collimators

Chao Li, Xiao Chai, Linzhao Zhuo, Bochao Wei, Ardalan Lotfi, Farrokh Ayazi, Chandra Raman

Published Sep 19, 2023• 3 citations

Abstract

We have developed a compact and highly efficient assembly for stimulated laser cooling of thermal rubidium atomic beams traveling upon planar silicon devices. Following precollimation via a silicon microchannel array, we perform beam brightening via a blue-detuned optical molasses [Aspect et al., Phys. Rev. Lett. 57, 1688 (1986)]. Owing to the small size of the chip elements, we require only 8 mW to implement the efficient cooling scheme, making it well suited for future portable atomic sensors that require minimal size, weight, and power consumption. Small mirrors are fabricated and hand-assembled to precisely overlap a strong elliptical standing wave with a sheet-shaped atomic density distribution, with dimensions chosen precisely to match these. We reduce the transverse velocity spread to below 1 m/s within an interaction length of 4.5 mm above the silicon substrate. We use Doppler-sensitive two-photon Raman spectroscopy to characterize the cooling. In contrast to time-of-flight methods utilized previously, this approach requires a much shorter apparatus to achieve similar resolution. This hybrid of passive and active collimation paves the way toward the construction of fully fledged atomic instruments, such as atomic beam clocks and gyroscopes, entirely on-chip through batch-fabricated processes.

DOI: 10.1103/physrevapplied.20.034042

Related papers

Cascaded collimator for atomic beams traveling in planar silicon devices

Chao Li, Xiao Chai, Bochao Wei +4 more

Micro- and increasingly, nano-fabrication have enabled the miniaturization of atomic devices, from vapor cells to atom chips for Bose-Einstein condensation. Here we present microfabricated planar devices for thermal atomic beams. Etched microchannels were used to create highly collimated, continuous rubidium atom beams traveling parallel to a silicon wafer surface. Precise, lithographic definition of the guiding channels allowed for shaping and tailoring the velocity distributions in ways not possible using conventional machining. Multiple miniature beams with individually prescribed geometries were created, including collimated, focusing and diverging outputs. A "cascaded" collimator was realized with 40 times greater purity than conventional collimators. These localized, miniature atom beam sources can be a valuable resource for a number of quantum technologies, including atom interferometers, clocks, Rydberg atoms, and hybrid atom-nanophotonic systems, as well as enabling controlled studies of atom-surface interactions at the nanometer scale.

Nature Communications•Apr 23, 2019•32 citations

Cascaded collimator for atomic beams traveling in planar silicon devices

Chao Li, Xiao Chai, Bochao Wei +4 more

Abstract Micro- and increasingly, nano-fabrication have enabled the miniaturization of atomic devices, from vapor cells to atom chips for Bose-Einstein condensation. Here we present microfabricated planar devices for thermal atomic beams. Etched microchannels were used to create highly collimated, continuous rubidium atom beams traveling parallel to a silicon wafer surface. Precise, lithographic definition of the guiding channels allowed for shaping and tailoring the velocity distributions in ways not possible using conventional machining. Multiple miniature beams with individually prescribed geometries were created, including collimated, focusing and diverging outputs. A “cascaded” collimator was realized with 40 times greater purity than conventional collimators. These localized, miniature atom beam sources can be a valuable resource for a number of quantum technologies, including atom interferometers, clocks, Rydberg atoms, and hybrid atom-nanophotonic systems, as well as enabling controlled studies of atom-surface interactions at the nanometer scale.

APS Division of Atomic, Molecular and Optical Physics Meeting Abstracts•May 1, 2019•0 citations

Chip-Scale Packages for a Tunable Wavelength Reference and Laser Cooling Platform

S. Dyer, Kevin Francis Gallacher, Ugnė Hawley +6 more

The miniaturization of cold-atom systems brings high accuracy into portable atomic metrology. However, the impact of cold-atom sensors in real-world applications has been limited by the overall laser cooling package. This study amalgamates a chip-scale optics setup with a microfabricated laser cooling system to dramatically reduce device size, weight, and power usage. The authors use an on-chip Zeeman offset lock for laser cooling, and demonstrate improved atom number afforded by new techniques in silicon cell fabrication. The simplicity, scalability, and utility demonstrated in this cold-atom platform will enable exciting opportunities in portable cold-atom clocks and interferometers.

Physical Review Applied•Apr 5, 2023•19 citations

Cooling Atoms with Stimulated Emission

Alain Aspect, Jean Dalibard, A. Heidmann +2 more

We have observed an efficient collimation of a cesium atomic beam crossing at right angles an intense laser standing wave. This new cooling scheme is mainly based on a stimulated redistribution of photons between the two counterpropagating waves by the moving atoms. By contrast with usual radiation pressure cooling, this "stimulated molasses" works for blue detuning and does not saturate at high intensity.

Physical Review Letters•Oct 6, 1986•187 citations

Collimated versatile atomic beam source with alkali dispensers

Bochao Wei, Alexandra Crawford, Yorick Andeweg +3 more

Alkali metal dispensers have become an indispensable tool in the production of atomic vapors for magnetometry, alkali vapor cell clocks, and laser cooling experiments. A primary advantage of these dispensers is that they contain alkali metal in an inert form that can be exposed to air without hazard. However, their high temperature of operation (>600 °C) is undesirable for many applications, as it shifts the atomic speed distribution to higher values and presents a radiative heat source that can raise the temperature of its surroundings. For this reason, dispensers are typically not used in line-of-sight applications, such as atomic beam generation. In this work, we present an integrated rubidium dispenser collimating device with a thickness of only 2 mm that produces a beam of atoms traveling primarily in the forward direction. We find that the collimator plate serves to both shield the dispenser's radiation and moderate the velocity of the atomic beam so that the measured longitudinal speed distribution is comparable to that of an ordinary alkali oven at only a slightly elevated temperature of 200 °C. To confirm our theory, we also constructed another compact apparatus consisting of a dispenser and a silicon collimator and the measurements support our conclusion. Our integrated dispenser collimator will particularly be useful in integrated photonics and cavity QED on-chip, where a localized, directed source of Rb vapor in small quantities is needed.

arXiv:2202.07076•Applied Physics Letters•Apr 4, 2022•6 citations

Number enhancement for compact laser-cooled atomic samples by use of stimulated radiation forces

Elizabeth A. Donley, Tara Cubel Liebisch, E. Blanshan +1 more

For cold samples of laser-cooled atoms to be useful in emerging technologies such as compact atomic clocks and sensors, it is necessary to achieve small sample sizes while retaining a large number of cold atoms. Achieving large atom numbers in a small system is a major challenge for producing miniaturized laser-cooled atomic clocks, since the number of captured atoms in a vapor-cell magneto-optical trap (MOT) scales as the fourth power of the laser beam diameter. This strong dependence on size is fundamentally set by the maximum spontaneous light force ħkγ/2, where ħk is the photon momentum and γ/2 is the maximum spontaneous photon scatter rate of a saturated transition of linewidth γ. We are attempting to surmount the limit imposed by spontaneous emission by using bichromatic cooling - a technique that uses stimulated emission to slow the atoms. We have built a table-top experiment that uses stimulated-emission bichromatic cooling to pre-cool rubidium atoms and dramatically enhance the trappable atom number in a small MOT. The apparatus lets us test how bichromatic cooling scales with miniaturization. Here we report on our first experimental results of cooling a thermal beam of rubidium atoms down to MOT capture velocities.

Joint Conference of the European Frequency and Time Forum and IEEE International Frequency Control Symposium (EFTF/IFCS)•Jun 1, 2010•1 citation

We have developed a compact and highly efficient assembly for stimulated laser cooling of thermal rubidium atomic beams traveling upon planar silicon devices. Following precollimation via a silicon microchannel array, we perform beam brightening via a blue-detuned optical molasses [Aspect et al., Phys. Rev. Lett. 57, 1688 (1986)]. Owing to the small size of the chip elements, we require only 8 mW to implement the efficient cooling scheme, making it well suited for future portable atomic sensors that require minimal size, weight, and power consumption. Small mirrors are fabricated and hand-assembled to precisely overlap a strong elliptical standing wave with a sheet-shaped atomic density distribution, with dimensions chosen precisely to match these. We reduce the transverse velocity spread to below 1 m/s within an interaction length of 4.5 mm above the silicon substrate. We use Doppler-sensitive two-photon Raman spectroscopy to characterize the cooling. In contrast to time-of-flight methods utilized previously, this approach requires a much shorter apparatus to achieve similar resolution. This hybrid of passive and active collimation paves the way toward the construction of fully fledged atomic instruments, such as atomic beam clocks and gyroscopes, entirely on-chip through batch-fabricated processes.

Micro- and increasingly, nano-fabrication have enabled the miniaturization of atomic devices, from vapor cells to atom chips for Bose-Einstein condensation. Here we present microfabricated planar devices for thermal atomic beams. Etched microchannels were used to create highly collimated, continuous rubidium atom beams traveling parallel to a silicon wafer surface. Precise, lithographic definition of the guiding channels allowed for shaping and tailoring the velocity distributions in ways not possible using conventional machining. Multiple miniature beams with individually prescribed geometries were created, including collimated, focusing and diverging outputs. A "cascaded" collimator was realized with 40 times greater purity than conventional collimators. These localized, miniature atom beam sources can be a valuable resource for a number of quantum technologies, including atom interferometers, clocks, Rydberg atoms, and hybrid atom-nanophotonic systems, as well as enabling controlled studies of atom-surface interactions at the nanometer scale.

Abstract Micro- and increasingly, nano-fabrication have enabled the miniaturization of atomic devices, from vapor cells to atom chips for Bose-Einstein condensation. Here we present microfabricated planar devices for thermal atomic beams. Etched microchannels were used to create highly collimated, continuous rubidium atom beams traveling parallel to a silicon wafer surface. Precise, lithographic definition of the guiding channels allowed for shaping and tailoring the velocity distributions in ways not possible using conventional machining. Multiple miniature beams with individually prescribed geometries were created, including collimated, focusing and diverging outputs. A “cascaded” collimator was realized with 40 times greater purity than conventional collimators. These localized, miniature atom beam sources can be a valuable resource for a number of quantum technologies, including atom interferometers, clocks, Rydberg atoms, and hybrid atom-nanophotonic systems, as well as enabling controlled studies of atom-surface interactions at the nanometer scale.

The miniaturization of cold-atom systems brings high accuracy into portable atomic metrology. However, the impact of cold-atom sensors in real-world applications has been limited by the overall laser cooling package. This study amalgamates a chip-scale optics setup with a microfabricated laser cooling system to dramatically reduce device size, weight, and power usage. The authors use an on-chip Zeeman offset lock for laser cooling, and demonstrate improved atom number afforded by new techniques in silicon cell fabrication. The simplicity, scalability, and utility demonstrated in this cold-atom platform will enable exciting opportunities in portable cold-atom clocks and interferometers.

Alkali metal dispensers have become an indispensable tool in the production of atomic vapors for magnetometry, alkali vapor cell clocks, and laser cooling experiments. A primary advantage of these dispensers is that they contain alkali metal in an inert form that can be exposed to air without hazard. However, their high temperature of operation (>600 °C) is undesirable for many applications, as it shifts the atomic speed distribution to higher values and presents a radiative heat source that can raise the temperature of its surroundings. For this reason, dispensers are typically not used in line-of-sight applications, such as atomic beam generation. In this work, we present an integrated rubidium dispenser collimating device with a thickness of only 2 mm that produces a beam of atoms traveling primarily in the forward direction. We find that the collimator plate serves to both shield the dispenser's radiation and moderate the velocity of the atomic beam so that the measured longitudinal speed distribution is comparable to that of an ordinary alkali oven at only a slightly elevated temperature of 200 °C. To confirm our theory, we also constructed another compact apparatus consisting of a dispenser and a silicon collimator and the measurements support our conclusion. Our integrated dispenser collimator will particularly be useful in integrated photonics and cavity QED on-chip, where a localized, directed source of Rb vapor in small quantities is needed.

For cold samples of laser-cooled atoms to be useful in emerging technologies such as compact atomic clocks and sensors, it is necessary to achieve small sample sizes while retaining a large number of cold atoms. Achieving large atom numbers in a small system is a major challenge for producing miniaturized laser-cooled atomic clocks, since the number of captured atoms in a vapor-cell magneto-optical trap (MOT) scales as the fourth power of the laser beam diameter. This strong dependence on size is fundamentally set by the maximum spontaneous light force ħkγ/2, where ħk is the photon momentum and γ/2 is the maximum spontaneous photon scatter rate of a saturated transition of linewidth γ. We are attempting to surmount the limit imposed by spontaneous emission by using bichromatic cooling - a technique that uses stimulated emission to slow the atoms. We have built a table-top experiment that uses stimulated-emission bichromatic cooling to pre-cool rubidium atoms and dramatically enhance the trappable atom number in a small MOT. The apparatus lets us test how bichromatic cooling scales with miniaturization. Here we report on our first experimental results of cooling a thermal beam of rubidium atoms down to MOT capture velocities.