Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2204.01903 · Superconductor Science and Technology

An optical transition-edge sensor with high energy resolution

K. Hattori, Toshio Konno, Yoshitaka Miura, Sachiko Takasu, Daiji Fukuda

Published Jul 5, 2022• 39 citations
arXivHTMLPDF

Abstract

Abstract Optical transition-edge sensors (TESs) have shown an energy resolution for resolving the number of incident photons at the telecommunication wavelength. However, a higher energy resolution is required for biological imaging and microscopic spectroscopy. In this study, we tested an Au/Ti (10/20 nm) bilayer TES that showed a high energy resolution. The high energy resolution was achieved by lowering the critical temperature T c to 115 mK, and the resultant energy resolution was 67 meV full width at half maximum (FWHM) at 0.8 eV. When T c was reduced to 115 mK, the theoretical resolution would scale up to 30 meV FWHM, considering that the typical energy resolution of optical TESs was 150 meV and T c was 300 mK. To investigate the difference between the theoretical expectation (30 meV) and the measured value (67 meV), we measured the complex impedance and current noise of the TES. We found excess Johnson noise in the TES; the excess Johnson noise term M was 1.5 at a bias point where the resistance was 10% of the normal resistance. For reference, the above mentioned TES was compared with a TES showing typical energy resolution (156 meV FWHM). We also discussed factors that improved or inhibited the energy resolution.

DOI
10.1088/1361-6668/ac7e7b

Related papers

Development of High Detection Efficiency Titanium Transition-Edge Sensors for 1550 nm Single-Photon Detection

Xiaolong Xu, Peizhan Li, Carlo Pepe +10 more

Transition-edge sensors (TESs) have shown the capability of both energy resolution and resolving photon numbers. In this work, we present the fabrication and characterization of high detection efficiency Ti optical TESs with the critical temperatureTc= 213 mK and the photon-number resolving capability at telecommunication wavelength 1550 nm. The Ti superconducting film is prepared by a DC magnetron sputtering technique. An optical cavity comprised of 5-layers antireflection and 15-layers high-reflection Ta2O5/SiO2is enclosed with the Ti film by an ion beam assisted deposition method to improve detection efficiency, which brings the absorption of 99.74%. The energy resolution for the Ti TES with sensitive area 20 μm × 20 μm is 0.45 eV and the detection efficiency is 97% ± 1%.

IEEE Transactions on Applied Superconductivity•Jan 12, 2026•2 citations

Single-photon light detection with transition-edge sensors

M. Rajteri, E. Taralli, Chiara Portesi +1 more

Transition-Edge Sensors (TESs) are microcalorimeters that measure the energy of incident single photons by the resistance increase of a superconducting film biased within the superconducting-to-normal transition. TES are able to detect single photons from IR to X-ray with an intrinsic energy resolution and photon-number discrimination capability. Metrology, astronomy and quantum \ncommunication are the fields where these properties can be particularly useful. In this work, we report about characterization of different TESs based on Ti films. Single photons have been detected from 200nm to 800 nm working at transition temperature Tc ∼ 100 mK. Using a pulsed laser at 690nm we have demonstrated the capability to resolve up to five photons.

NCimC•Jul 1, 2008•2 citations

High intrinsic energy resolution photon number resolving detectors

L. Lolli, E. Taralli, Chiara Portesi +2 more

Transition Edge Sensors (TESs) are characterized by the intrinsic figures of merit to resolve both the energy and the statistical distribution of the incident photons. These properties lead TES devices to become the best single photon detectors for quantum technology experiments. For a TES based on titanium and gold, has been reached, at telecommunication wavelength, an unprecedented intrinsic energy resolution (0.113 eV). The uncertainty analysis of both energy resolution and photon state assignment has been discussed. The thermal properties of the superconductive device have been studied by fitting the bias curves to evaluate the theoretical limit of the energy resolution.

arXiv:1306.5385•Applied Physics Letters•Jul 22, 2013•41 citations

Development of transition-edge sensors with high detection efficiency and fast response time

Takeshi Jodoi, Tetsuya Tsuruta, Takahiro Kikuchi +4 more

This study developed transition-edge sensors (TESs), which can achieve high detection efficiency and fast response time through an optimized optical cavity design. Their suitability for optical quantum information processing was confirmed. Furthermore, we developed TESs with two different sensitive area sizes—8 × 7 ţm2, 12 × 11 ţm2—and systematically evaluated their performances. By employing a titanium (Ti)/gold (Au) bilayer with a relatively high transition temperature as the sensitive element, we achieved a fast total response time—defined as the sum of the rise and decay times—of ∼160 ns. Furthermore, the optical cavity structure—predicted by simulations to achieve a photon absorptance of 99.9% at 1550 nm—yielded measured system detection efficiencies of 94.7% ± 0.62% for the 8 × 7 ţm2 TES and 99.0% ± 0.60% for the 12 × 11 ţm2 TES. Photon response measurements indicate an energy resolution of 0.20 eV for the 8 × 7 ţm2 TES and 0.37 eV for the 12 × 11 ţm2 TES. These results establish that the proposed TESs are the fastest and most efficient devices reported to date. The proposed devices offer a high detection efficiency, high count rate, and accurate photon-number resolution. Therefore, they provide a breakthrough platform for scalable fault-tolerant quantum information processing and enable significant advances in experimental quantum optics.

APL Photonics•Jul 1, 2026•0 citations

Fabrication and Characterization of Fast TESs With Small Area for Single Photon Counting

Chiara Portesi, E. Taralli, L. Lolli +2 more

Transition edge sensors (TESs) with high energy resolution (ΔE) at telecommunication wavelengths have been realized in the last years for application to experiments of quantum optics and quantum information. In these fields, lasers with repetition rate of the order of 50 MHz are usually applied and hence TES with recovery times lower than 20 ns would be desirable. To this aim, Ti TESs with area ranging between 1 μm × 1 μm and 2 μm × 2 μm are fabricated and characterized, to study the effects of the different sizes of active areas and critical temperatures on the energy resolutions and on the response times. Titanium TESs have been fabricated by thermal evaporation and Electron Beam Lithography technique on Si/SiN substrates, and they have been electrically and optically characterized. The experimental data have been analyzed and correlated to the detector geometrical parameters. The superconducting transitions of TESs with areas down to 1 μm × 1 μm result to be affected by lateral proximity effects of Nb wirings. Ti TESs with critical temperature of 470 mK show response time of about 150 ns and energy resolution of 0.16 eV.

IEEE Transactions on Applied Superconductivity•Nov 20, 2014•20 citations

Titanium TES based photon number resolving detectors with 1 MHz counting rate and 65% quantum efficiency

Daiji Fukuda, Go Fujii, Takayuki Numata +4 more

A transition edge sensor (TES) is one of superconducting photon detectors, which has a photon number resolving ability in light pulses. The TES device is a kind of calorimeters operated at an extremely low temperature, and the energy of the photons is measured as a resistance change in a superconducting transition region of the TES. The advantages of the TESs are an excellent energy resolution and a high quantum efficiency. However a response speed is limited due to slow thermal recovery time. To overcome this, we fabricated new TES devices which are based on a titanium superconductor. The critical temperature of our titanium films is around 410 mK, which greatly improves the thermal recovery time. The observed decay time constant of response signals to the light pulses is around several hundreds of ns, that make it possible to operate the devices at a counting rate over 1 MHz. The photon number resolving power is 0.35 eV(FWHM) for a 5 μm size device even at the high operating temperature. The system quantum efficiency is 65 % by embedding the TES films in an optical structure with a high reflection dielectric mirror and an anti-reflection coatings fabricated by an ion beam assisted sputtering method. These features are very promising for high speed photon number resolving applications in the quantum information field.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Dec 2, 2008•11 citations
Abstract Optical transition-edge sensors (TESs) have shown an energy resolution for resolving the number of incident photons at the telecommunication wavelength. However, a higher energy resolution is required for biological imaging and microscopic spectroscopy. In this study, we tested an Au/Ti (10/20 nm) bilayer TES that showed a high energy resolution. The high energy resolution was achieved by lowering the critical temperature T c to 115 mK, and the resultant energy resolution was 67 meV full width at half maximum (FWHM) at 0.8 eV. When T c was reduced to 115 mK, the theoretical resolution would scale up to 30 meV FWHM, considering that the typical energy resolution of optical TESs was 150 meV and T c was 300 mK. To investigate the difference between the theoretical expectation (30 meV) and the measured value (67 meV), we measured the complex impedance and current noise of the TES. We found excess Johnson noise in the TES; the excess Johnson noise term M was 1.5 at a bias point where the resistance was 10% of the normal resistance. For reference, the above mentioned TES was compared with a TES showing typical energy resolution (156 meV FWHM). We also discussed factors that improved or inhibited the energy resolution.
Transition-edge sensors (TESs) have shown the capability of both energy resolution and resolving photon numbers. In this work, we present the fabrication and characterization of high detection efficiency Ti optical TESs with the critical temperatureTc= 213 mK and the photon-number resolving capability at telecommunication wavelength 1550 nm. The Ti superconducting film is prepared by a DC magnetron sputtering technique. An optical cavity comprised of 5-layers antireflection and 15-layers high-reflection Ta2O5/SiO2is enclosed with the Ti film by an ion beam assisted deposition method to improve detection efficiency, which brings the absorption of 99.74%. The energy resolution for the Ti TES with sensitive area 20 μm × 20 μm is 0.45 eV and the detection efficiency is 97% ± 1%.
Transition-Edge Sensors (TESs) are microcalorimeters that measure the energy of incident single photons by the resistance increase of a superconducting film biased within the superconducting-to-normal transition. TES are able to detect single photons from IR to X-ray with an intrinsic energy resolution and photon-number discrimination capability. Metrology, astronomy and quantum \ncommunication are the fields where these properties can be particularly useful. In this work, we report about characterization of different TESs based on Ti films. Single photons have been detected from 200nm to 800 nm working at transition temperature Tc ∼ 100 mK. Using a pulsed laser at 690nm we have demonstrated the capability to resolve up to five photons.
Transition Edge Sensors (TESs) are characterized by the intrinsic figures of merit to resolve both the energy and the statistical distribution of the incident photons. These properties lead TES devices to become the best single photon detectors for quantum technology experiments. For a TES based on titanium and gold, has been reached, at telecommunication wavelength, an unprecedented intrinsic energy resolution (0.113 eV). The uncertainty analysis of both energy resolution and photon state assignment has been discussed. The thermal properties of the superconductive device have been studied by fitting the bias curves to evaluate the theoretical limit of the energy resolution.
This study developed transition-edge sensors (TESs), which can achieve high detection efficiency and fast response time through an optimized optical cavity design. Their suitability for optical quantum information processing was confirmed. Furthermore, we developed TESs with two different sensitive area sizes—8 × 7 ţm2, 12 × 11 ţm2—and systematically evaluated their performances. By employing a titanium (Ti)/gold (Au) bilayer with a relatively high transition temperature as the sensitive element, we achieved a fast total response time—defined as the sum of the rise and decay times—of ∼160 ns. Furthermore, the optical cavity structure—predicted by simulations to achieve a photon absorptance of 99.9% at 1550 nm—yielded measured system detection efficiencies of 94.7% ± 0.62% for the 8 × 7 ţm2 TES and 99.0% ± 0.60% for the 12 × 11 ţm2 TES. Photon response measurements indicate an energy resolution of 0.20 eV for the 8 × 7 ţm2 TES and 0.37 eV for the 12 × 11 ţm2 TES. These results establish that the proposed TESs are the fastest and most efficient devices reported to date. The proposed devices offer a high detection efficiency, high count rate, and accurate photon-number resolution. Therefore, they provide a breakthrough platform for scalable fault-tolerant quantum information processing and enable significant advances in experimental quantum optics.
Transition edge sensors (TESs) with high energy resolution (ΔE) at telecommunication wavelengths have been realized in the last years for application to experiments of quantum optics and quantum information. In these fields, lasers with repetition rate of the order of 50 MHz are usually applied and hence TES with recovery times lower than 20 ns would be desirable. To this aim, Ti TESs with area ranging between 1 μm × 1 μm and 2 μm × 2 μm are fabricated and characterized, to study the effects of the different sizes of active areas and critical temperatures on the energy resolutions and on the response times. Titanium TESs have been fabricated by thermal evaporation and Electron Beam Lithography technique on Si/SiN substrates, and they have been electrically and optically characterized. The experimental data have been analyzed and correlated to the detector geometrical parameters. The superconducting transitions of TESs with areas down to 1 μm × 1 μm result to be affected by lateral proximity effects of Nb wirings. Ti TESs with critical temperature of 470 mK show response time of about 150 ns and energy resolution of 0.16 eV.
A transition edge sensor (TES) is one of superconducting photon detectors, which has a photon number resolving ability in light pulses. The TES device is a kind of calorimeters operated at an extremely low temperature, and the energy of the photons is measured as a resistance change in a superconducting transition region of the TES. The advantages of the TESs are an excellent energy resolution and a high quantum efficiency. However a response speed is limited due to slow thermal recovery time. To overcome this, we fabricated new TES devices which are based on a titanium superconductor. The critical temperature of our titanium films is around 410 mK, which greatly improves the thermal recovery time. The observed decay time constant of response signals to the light pulses is around several hundreds of ns, that make it possible to operate the devices at a counting rate over 1 MHz. The photon number resolving power is 0.35 eV(FWHM) for a 5 μm size device even at the high operating temperature. The system quantum efficiency is 65 % by embedding the TES films in an optical structure with a high reflection dielectric mirror and an anti-reflection coatings fabricated by an ion beam assisted sputtering method. These features are very promising for high speed photon number resolving applications in the quantum information field.