Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2011.02634 · Physical Review X

Fast Logic with Slow Qubits: Microwave-Activated Controlled-Z Gate on Low-Frequency Fluxoniums

Quentin Ficheux, Long B. Nguyen, Aaron Somoroff, Haonan Xiong, Konstantin Nesterov, Maxim Vavilov, Vladimir Manucharyan

Published May 3, 2021• 68 citations
arXivHTMLPDF

Abstract

We demonstrate a controlled-Z gate between capacitively coupled fluxonium qubits with transition frequencies $72.3~\textrm{MHz}$ and $136.3~\textrm{MHz}$. The gate is activated by a $61.6~\textrm{ns}$ long pulse at the frequency between non-computational transitions $|10\rangle - |20\rangle$ and $|11\rangle - |21\rangle$, during which the qubits complete only $4$ and $8$ Larmor periods, respectively. The measured gate error of $(8\pm1)\times 10^{-3}$ is limited by decoherence in the non-computational subspace, which will likely improve in the next generation devices. Although our qubits are about fifty times slower than transmons, the two-qubit gate is faster than microwave-activated gates on transmons, and the gate error is on par with the lowest reported. Architectural advantages of low-frequency fluxoniums include long qubit coherence time, weak hybridization in the computational subspace, suppressed residual $ZZ$-coupling rate (here $46~\mathrm{kHz}$), and absence of either excessive parameter matching or complex pulse shaping requirements.

DOI
10.1103/physrevx.11.021026

Related papers

Microwave-activated gates between a fluxonium and a transmon qubit

Alessandro Ciani, Boris Varbanov, N. Jolly +2 more

We propose and analyze two types of microwave-activated gates between a fluxonium and a transmon qubit, namely a cross-resonance (CR) and a CPHASE gate. The large frequency difference between a transmon and a fluxonium makes the realization of a two-qubit gate challenging. For a medium-frequency fluxonium qubit, the transmon-fluxonium system allows for a cross-resonance effect mediated by the higher levels of the fluxonium over a wide range of transmon frequencies. This allows one to realize the cross-resonance gate by driving the fluxonium at the transmon frequency, mitigating typical problems of the cross-resonance gate in transmon-transmon chips related to frequency targeting and residual ZZ coupling. However, when the fundamental frequency of the fluxonium enters the low-frequency regime below 100 MHz, the cross-resonance effect decreases leading to long gate times. For this range of parameters, a fast microwave CPHASE gate can be implemented using the higher levels of the fluxonium. In both cases, we perform numerical simulations of the gate showing that a gate fidelity above 99% can be obtained with gate times between 100 and 300 ns. Next to a detailed gate analysis, we perform a study of chip yield for a surface code lattice of fluxonia and transmons interacting via the proposed cross-resonance gate. We find a much better yield as compared to a transmon-only architecture with the cross-resonance gate as native two-qubit gate.

•Jan 1, 2022•0 citations

Microwave-activated controlled- Z gate for fixed-frequency fluxonium qubits

Konstantin Nesterov, Ivan Pechenezhskiy, Chen Wang +2 more

The superconducting fluxonium circuit is an artificial atom with a strongly anharmonic spectrum: When biased at a half flux quantum, the lowest qubit transition is an order of magnitude smaller in frequency than those to higher levels. Similar to conventional atomic systems, such a frequency separation between the computational and noncomputational subspaces allows independent optimizations of the qubit coherence and two-qubit interactions. Here, we describe a controlled-$Z$ gate for two fluxoniums connected either capacitively or inductively, with qubit transitions fixed near $500\phantom{\rule{3.33333pt}{0ex}}\mathrm{MHz}$. The gate is activated by a microwave drive at a resonance involving the second excited state. We estimate intrinsic gate fidelities over 99.9% with gate times below 100 ns.

arXiv:1802.03095•Physical Review A•Sep 24, 2018•38 citations

Proposal for Entangling Gates on Fluxonium Qubits via a Two-Photon Transition

Konstantin Nesterov, Quentin Ficheux, Vladimir E. Manucharyan +1 more

We propose a family of microwave-activated entangling gates on two capacitively coupled fluxonium qubits.A microwave pulse applied to either qubit at a frequency near the half-frequency of the |00 -|11 transition induces two-photon Rabi oscillations with a negligible leakage outside the computational subspace, owing to the strong anharmonicity of fluxoniums.By adjusting the drive frequency, amplitude, and duration, we obtain the gate family that is locally equivalent to the fermionic-simulation gates such as √ SWAP-like and controlled-phase gates.The gate error can be tuned below 10 -4 for a pulse duration under 100 ns without excessive circuit parameter matching.Given that the fluxonium coherence time can exceed 1 ms, our gate scheme is promising for large-scale quantum processors.

arXiv:2011.10011•PRX Quantum•Jun 22, 2021•24 citations

Microwave-activated gates between a fluxonium and a transmon qubit

Alessandro Ciani, Boris Varbanov, N. Jolly +2 more

We propose and analyze two types of microwave-activated gates between a fluxonium and a transmon qubit, namely a cross-resonance (CR) and a CPHASE gate. The large frequency difference between a transmon and a fluxonium makes the realization of a two-qubit gate challenging. For a medium-frequency fluxonium qubit, the transmon-fluxonium system allows for a cross-resonance effect mediated by the higher levels of the fluxonium over a wide range of transmon frequencies. This allows one to realize the cross-resonance gate by driving the fluxonium at the transmon frequency, mitigating typical problems of the cross-resonance gate in transmon-transmon chips related to frequency targeting and residual $ZZ$ coupling. However, when the fundamental frequency of the fluxonium enters the low-frequency regime below $100\phantom{\rule{0.16em}{0ex}}\mathrm{MHz}$, the cross-resonance effect decreases leading to long gate times. For this range of parameters, a fast microwave CPHASE gate can be implemented using the higher levels of the fluxonium. In both cases, we perform numerical simulations of the gate showing that a gate fidelity above $99%$ can be obtained with gate times between 100 and $300\phantom{\rule{0.16em}{0ex}}\mathrm{ns}$. Next to a detailed gate analysis, we perform a study of chip yield for a surface code lattice of fluxonia and transmons interacting via the proposed cross-resonance gate. We find a much better yield as compared to a transmon-only architecture with the cross-resonance gate as native two-qubit gate.

arXiv:2206.06203•Physical Review Research•Nov 22, 2022•8 citations

Fast microwave-driven two-qubit gates between fluxonium qubits with a transmon coupler

Siddharth Singh, Eugene Y. Huang, Jinlun Hu +6 more

Two qubit gates constitute fundamental building blocks in the realization of large-scale quantum devices. Using superconducting circuits, two-qubit gates have previously been implemented in different ways with each method aiming to maximize gate fidelity. Another important goal of a new gate scheme is to minimize the complexity of gate calibration. In this work, we demonstrate a high-fidelity two-qubit gate between two fluxonium qubits enabled by an intermediate capacitively coupled transmon. The coupling strengths between the qubits and the coupler are designed to minimize residual crosstalk while still allowing for fast gate operations. The gate is based on frequency selectively exciting the coupler using a microwave drive to complete a 2$π$ rotation, conditional on the state of the fluxonium qubits. When successful, this drive scheme implements a conditional phase gate. Using analytically derived pulse shapes, we minimize unwanted excitations of the coupler and obtain gate errors of $10^{-2}$ for gate times below 60~ns. At longer durations, our gate is limited by relaxation of the coupler. Our results show how carefully designed control pulses can speed up frequency selective entangling gates.

arXiv:2504.13718•Physical Review Applied•Oct 28, 2025•5 citations

Interaction-Resilient Scalable Fluxonium Architecture with All-Microwave Gates

Andrei A. Kugut, Grigoriy S. Mazhorin, Ilya A. Simakov

Fluxonium qubits demonstrate exceptional potential for quantum processing; yet, realizing scalable architectures using them remains challenging. We propose a fluxonium-based square-grid design with fast $\sim63$~ns controlled-Z (CZ) gates, achieving coherent errors below $10^{-4}$, activated via microwave-driven transmon couplers. A central difficulty in such large-scale systems with all-microwave gates and, therefore, strong static couplings, is suppressing parasitic interactions that extend beyond nearest neighbors to include next-nearest elements. We address this issue by introducing several design strategies: the frequency allocation of both qubits and couplers, the localization of coupler wavefunctions, and a differential oscillator that suppresses residual long-range interactions. In addition, the architecture natively supports fast $\sim70$~ns CZZ gates -- three-qubit operations composed of two CZ gates sharing a common qubit -- which reduce the incoherent error by $\sim 35\%$ compared to performing the corresponding CZs sequentially. Together, these advances establish an interaction-resilient platform for large-scale fluxonium processors and can be adapted to a variety of fluxonium layouts.

quant-pharXiv:2512.21189•Dec 25, 2025•0 citations
We demonstrate a controlled-Z gate between capacitively coupled fluxonium qubits with transition frequencies 72.3 MHz72.3~\textrm{MHz}72.3 MHz and 136.3 MHz136.3~\textrm{MHz}136.3 MHz. The gate is activated by a 61.6 ns61.6~\textrm{ns}61.6 ns long pulse at the frequency between non-computational transitions ∣10⟩−∣20⟩|10\rangle - |20\rangle∣10⟩−∣20⟩ and ∣11⟩−∣21⟩|11\rangle - |21\rangle∣11⟩−∣21⟩, during which the qubits complete only 444 and 888 Larmor periods, respectively. The measured gate error of (8±1)×10−3(8\pm1)\times 10^{-3}(8±1)×10−3 is limited by decoherence in the non-computational subspace, which will likely improve in the next generation devices. Although our qubits are about fifty times slower than transmons, the two-qubit gate is faster than microwave-activated gates on transmons, and the gate error is on par with the lowest reported. Architectural advantages of low-frequency fluxoniums include long qubit coherence time, weak hybridization in the computational subspace, suppressed residual ZZZZZZ-coupling rate (here 46 kHz46~\mathrm{kHz}46 kHz), and absence of either excessive parameter matching or complex pulse shaping requirements.
We propose and analyze two types of microwave-activated gates between a fluxonium and a transmon qubit, namely a cross-resonance (CR) and a CPHASE gate. The large frequency difference between a transmon and a fluxonium makes the realization of a two-qubit gate challenging. For a medium-frequency fluxonium qubit, the transmon-fluxonium system allows for a cross-resonance effect mediated by the higher levels of the fluxonium over a wide range of transmon frequencies. This allows one to realize the cross-resonance gate by driving the fluxonium at the transmon frequency, mitigating typical problems of the cross-resonance gate in transmon-transmon chips related to frequency targeting and residual ZZ coupling. However, when the fundamental frequency of the fluxonium enters the low-frequency regime below 100 MHz, the cross-resonance effect decreases leading to long gate times. For this range of parameters, a fast microwave CPHASE gate can be implemented using the higher levels of the fluxonium. In both cases, we perform numerical simulations of the gate showing that a gate fidelity above 99% can be obtained with gate times between 100 and 300 ns. Next to a detailed gate analysis, we perform a study of chip yield for a surface code lattice of fluxonia and transmons interacting via the proposed cross-resonance gate. We find a much better yield as compared to a transmon-only architecture with the cross-resonance gate as native two-qubit gate.
The superconducting fluxonium circuit is an artificial atom with a strongly anharmonic spectrum: When biased at a half flux quantum, the lowest qubit transition is an order of magnitude smaller in frequency than those to higher levels. Similar to conventional atomic systems, such a frequency separation between the computational and noncomputational subspaces allows independent optimizations of the qubit coherence and two-qubit interactions. Here, we describe a controlled-ZZZ gate for two fluxoniums connected either capacitively or inductively, with qubit transitions fixed near 500MHz500\phantom{\rule{3.33333pt}{0ex}}\mathrm{MHz}500MHz. The gate is activated by a microwave drive at a resonance involving the second excited state. We estimate intrinsic gate fidelities over 99.9% with gate times below 100 ns.
We propose a family of microwave-activated entangling gates on two capacitively coupled fluxonium qubits.A microwave pulse applied to either qubit at a frequency near the half-frequency of the |00 -|11 transition induces two-photon Rabi oscillations with a negligible leakage outside the computational subspace, owing to the strong anharmonicity of fluxoniums.By adjusting the drive frequency, amplitude, and duration, we obtain the gate family that is locally equivalent to the fermionic-simulation gates such as √ SWAP-like and controlled-phase gates.The gate error can be tuned below 10 -4 for a pulse duration under 100 ns without excessive circuit parameter matching.Given that the fluxonium coherence time can exceed 1 ms, our gate scheme is promising for large-scale quantum processors.
We propose and analyze two types of microwave-activated gates between a fluxonium and a transmon qubit, namely a cross-resonance (CR) and a CPHASE gate. The large frequency difference between a transmon and a fluxonium makes the realization of a two-qubit gate challenging. For a medium-frequency fluxonium qubit, the transmon-fluxonium system allows for a cross-resonance effect mediated by the higher levels of the fluxonium over a wide range of transmon frequencies. This allows one to realize the cross-resonance gate by driving the fluxonium at the transmon frequency, mitigating typical problems of the cross-resonance gate in transmon-transmon chips related to frequency targeting and residual ZZZZZZ coupling. However, when the fundamental frequency of the fluxonium enters the low-frequency regime below 100MHz100\phantom{\rule{0.16em}{0ex}}\mathrm{MHz}100MHz, the cross-resonance effect decreases leading to long gate times. For this range of parameters, a fast microwave CPHASE gate can be implemented using the higher levels of the fluxonium. In both cases, we perform numerical simulations of the gate showing that a gate fidelity above 9999%99 can be obtained with gate times between 100 and 300ns300\phantom{\rule{0.16em}{0ex}}\mathrm{ns}300ns. Next to a detailed gate analysis, we perform a study of chip yield for a surface code lattice of fluxonia and transmons interacting via the proposed cross-resonance gate. We find a much better yield as compared to a transmon-only architecture with the cross-resonance gate as native two-qubit gate.
Two qubit gates constitute fundamental building blocks in the realization of large-scale quantum devices. Using superconducting circuits, two-qubit gates have previously been implemented in different ways with each method aiming to maximize gate fidelity. Another important goal of a new gate scheme is to minimize the complexity of gate calibration. In this work, we demonstrate a high-fidelity two-qubit gate between two fluxonium qubits enabled by an intermediate capacitively coupled transmon. The coupling strengths between the qubits and the coupler are designed to minimize residual crosstalk while still allowing for fast gate operations. The gate is based on frequency selectively exciting the coupler using a microwave drive to complete a 2πππ rotation, conditional on the state of the fluxonium qubits. When successful, this drive scheme implements a conditional phase gate. Using analytically derived pulse shapes, we minimize unwanted excitations of the coupler and obtain gate errors of 10−210^{-2}10−2 for gate times below 60~ns. At longer durations, our gate is limited by relaxation of the coupler. Our results show how carefully designed control pulses can speed up frequency selective entangling gates.
Fluxonium qubits demonstrate exceptional potential for quantum processing; yet, realizing scalable architectures using them remains challenging. We propose a fluxonium-based square-grid design with fast ∼63\sim63∼63~ns controlled-Z (CZ) gates, achieving coherent errors below 10−410^{-4}10−4, activated via microwave-driven transmon couplers. A central difficulty in such large-scale systems with all-microwave gates and, therefore, strong static couplings, is suppressing parasitic interactions that extend beyond nearest neighbors to include next-nearest elements. We address this issue by introducing several design strategies: the frequency allocation of both qubits and couplers, the localization of coupler wavefunctions, and a differential oscillator that suppresses residual long-range interactions. In addition, the architecture natively supports fast ∼70\sim70∼70~ns CZZ gates -- three-qubit operations composed of two CZ gates sharing a common qubit -- which reduce the incoherent error by ∼35%\sim 35\%∼35% compared to performing the corresponding CZs sequentially. Together, these advances establish an interaction-resilient platform for large-scale fluxonium processors and can be adapted to a variety of fluxonium layouts.