Having accurate gate generation is essential for precise control of a quantum system. The generated gate usually suffers from linear and nonlinear distortion. Previous works have demonstrated how to use a qubit to correct linear frequency distortions but have not commented on how to handle nonlinear distortions. This is an important issue as we show that nonlinear amplitude distortions from the RF electronics can affect Rabi pulses by as much as 10%. We present work that demonstrates how a transmon qubit can be used as a highly sensitive cryogenic detector to characterize these nonlinear amplitude distortions. We show that a correction can drive these errors down to <1% over a 700 MHz range. This correction technique provides a method to minimize the effects of signal distortions and can be easily applied to broadband control pulses to produce higher fidelity arbitrary quantum gates.
Having accurate gate generation is essential for precise control of a quantum system. The generated gate usually suffers from linear and nonlinear distortion. Previous works have demonstrated how to use a qubit to correct linear frequency distortions but have not commented on how to handle nonlinear distortions. This is an important issue as we show that nonlinear amplitude distortions from the RF electronics can affect Rabi pulses by as much as 10%. We present work that demonstrates how a transmon qubit can be used as a highly sensitive cryogenic detector to characterize these nonlinear amplitude distortions. We show that a correction can drive these errors down to <1% over a 700 MHz range. This correction technique provides a method to minimize the effects of signal distortions and can be easily applied to broadband control pulses to produce higher fidelity arbitrary quantum gates.
Reducing errors in quantum gates is critical to the development of quantum computers. To do so, any distortions in the control signals should be identified; however, conventional tools are not always applicable when part of the system is under high vacuum, cryogenic, or microscopic. Here, we demonstrate a method to detect and compensate for amplitude-dependent phase changes, using the qubit itself as a probe. The technique is implemented using a microwave-driven trapped-ion qubit, where correcting phase distortions leads to a threefold improvement in the error of single-qubit gates implemented with pulses of different amplitudes, to attain state-of-the-art performance benchmarked at 1.6 ( 4 ) × 10 − 6 error per Clifford gate. Published by the American Physical Society 2024
The ability to execute high-fidelity operations is crucial to scaling up quantum devices to large numbers of qubits. However, signal distortions originating from nonlinear components in the control lines can limit the performance of single-qubit gates. In this work, we use a measurement based on error amplification to characterize and correct the small single-qubit rotation errors originating from the nonlinear scaling of the qubit drive rate with the amplitude of the programmed pulse. With our hardware, and for a 15-ns pulse, the rotation angles deviate by up to several degrees from a linear model. Using purity benchmarking, we find that control errors reach $2\ifmmode\times\else\texttimes\fi{}{10}^{\ensuremath{-}4}$, which accounts for half of the total gate error. Using cross-entropy benchmarking, we demonstrate arbitrary-angle single-qubit gates with coherence-limited errors of $2\ifmmode\times\else\texttimes\fi{}{10}^{\ensuremath{-}4}$ and leakage below $6\ifmmode\times\else\texttimes\fi{}{10}^{\ensuremath{-}5}$. While the exact magnitude of these errors is specific to our setup, the presented method is applicable to most sources of nonlinearity. Our work shows that the nonlinearity of qubit drive line components imposes a limit on the fidelity of single-qubit gates, independent of improvements in coherence times, circuit design, or leakage mitigation when not corrected for.
Experiments with superconducting circuits require careful calibration of the applied pulses and fields over a large frequency range. This remains an ongoing challenge as commercial semiconductor electronics are not able to probe signals arriving at the chip due to its cryogenic environment. Here, we demonstrate how the on-chip amplitude and frequency of a microwave signal can be inferred from the ac Stark shifts of higher transmon levels. In our time-resolved measurements we employ Ramsey fringes, allowing us to detect the amplitude of the systems transfer function over a range of several hundreds of MHz with an energy sensitivity on the order of 10−4. Combined with similar measurements for the phase of the transfer function, our sensing method can facilitate pulse correction for high fidelity quantum gates in superconducting circuits. Additionally, the potential to characterize arbitrary microwave fields promotes applications in related areas of research, such as quantum optics or hybrid microwave systems including photonic, mechanical or magnonic subsystems.
Control electronics for superconducting quantum processors have strict requirements for accurate command of the sensitive quantum states of their qubits. Hinging on the purity of ultra-phase-stable oscillators to upconvert very-low-noise baseband pulses, conventional control systems can become prohibitively complex and expensive when scaling to larger quantum devices, especially as high sampling rates become desirable for fine-grained pulse shaping. Few-gigahertz radio-frequency (RF) digital-to-analog converters (DACs) present a more economical avenue for high-fidelity control while simultaneously providing greater command over the spectrum of the synthesized signal. Modern RF DACs with extra-wide bandwidths are able to directly synthesize tones above their sampling rates, thereby keeping the system clock rate at a level compatible with modern digital logic systems while still being able to generate high-frequency pulses with arbitrary profiles. We have incorporated custom superconducting qubit control logic into off-the-shelf hardware capable of low-noise pulse synthesis up to 7.5 GHz using an RF DAC clocked at 5 GHz. Our approach enables highly linear and stable microwave synthesis over a wide bandwidth, giving rise to high-resolution control and a reduced number of required signal sources per qubit. We characterize the performance of the hardware using a five-transmon superconducting device and demonstrate consistently reduced two-qubit gate error (as low as 1.8%), which we show results from superior control chain linearity compared to traditional configurations. The exceptional flexibility and stability further establish a foundation for scalable quantum control beyond intermediate-scale devices.
Abstract Experiments with superconducting circuits require careful calibration of the applied pulses and fields over a large frequency range. This remains an ongoing challenge as commercial semiconductor electronics are not able to probe signals arriving at the chip due to its cryogenic environment. Here, we demonstrate how the on-chip amplitude and frequency of a microwave signal can be inferred from the ac Stark shifts of higher transmon levels. In our time-resolved measurements we employ Ramsey fringes, allowing us to detect the amplitude of the systems transfer function over a range of several hundreds of MHz with an energy sensitivity on the order of 10 −4 . Combined with similar measurements for the phase of the transfer function, our sensing method can facilitate pulse correction for high fidelity quantum gates in superconducting circuits. Additionally, the potential to characterize arbitrary microwave fields promotes applications in related areas of research, such as quantum optics or hybrid microwave systems including photonic, mechanical or magnonic subsystems.
Improving the speed and fidelity of quantum logic gates is essential to reach quantum advantage with future quantum computers. However, fast logic gates lead to increased leakage errors in superconducting quantum processors based on qubits with low anharmonicity, such as transmons. To reduce leakage errors, we propose and experimentally demonstrate two new analytical methods, Fourier ansatz spectrum tuning derivative removal by adiabatic gate (FAST DRAG) and higher-derivative (HD) DRAG, both of which enable shaping single-qubit control pulses in the frequency domain to achieve stronger suppression of leakage transitions compared to previously demonstrated pulse shapes. Using the new methods to suppress the e f transition of a transmon qubit with an anharmonicity of − 212 MHz, we implement R X ( π / 2 ) gates achieving a leakage error below 3.0 × 10 − 5 down to a gate duration of 6.25 ns without the need for iterative closed-loop optimization. The obtained leakage error represents a 20-fold reduction in leakage compared to a conventional cosine DRAG pulse. Employing the FAST DRAG method, we further achieve an error per gate of ( 1.56 ± 0.07 ) × 10 − 4 at a 7.9-ns gate duration, outperforming conventional pulse shapes both in terms of error and gate speed. Furthermore, we study error-amplifying measurements for the characterization of temporal microwave control-pulse distortions, and demonstrate that non-Markovian coherent errors caused by such distortions may be a significant source of error for sub-10-ns single-qubit gates unless corrected using predistortion. Published by the American Physical Society 2024