Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2002.00855 · Physical Review A

Microwave electrometry via electromagnetically induced absorption in cold Rydberg atoms

Kai-Yu Liao, Hai-Tao Tu, Shu-Zhe Yang, Changjun Chen, Xiaohong Liu, Jie Liang, Xin-Ding Zhang, Hui Yan, Shi-Liang Zhu

Published May 21, 2020• 115 citations
arXivHTMLPDF

Abstract

The atom-based traceable standard for microwave electrometry shows promising advantages by enabling stable and uniform measurement. Here we theoretically propose and then experimentally realize an alternative direct International System of Units (SI)--traceable and self-calibrated method for measuring a microwave-electric-field strength based on electromagnetically induced absorption (EIA) in cold Rydberg atoms. Comparing with the method of electromagnetically induced transparency, we show that the equivalence relation between the microwave Rabi frequency and Autler-Townes splitting is more valid and is even more robust against the experimental parameters in the EIA's linear region. Furthermore, a narrower linewidth of cold Rydberg EIA enables us to realize a direct SI-traceable microwave-electric-field measurement as small as $\ensuremath{\sim}100\phantom{\rule{4pt}{0ex}}\ensuremath{\mu}\mathrm{V}\phantom{\rule{0.16em}{0ex}}{\mathrm{cm}}^{\ensuremath{-}1}$.

DOI
10.1103/physreva.101.053432

Related papers

Span shift and extension of quantum microwave electrometry with Rydberg atoms dressed by an auxiliary microwave field

Feng-Dong Jia, Xiubin Liu, Jiong Mei +7 more

The Rydberg electromagnetically induced transparency (EIT)--Autler Townes (AT) splitting proportional to the target microwave electric field strength is an atom-based primary traceable standard in microwave electrometry. The minimum detected microwave electric field is limited when the EIT-AT splitting is indistinguishable. We design a method for auxiliary microwave-dressed Rydberg atoms that extends the electrometric span. We theoretically and experimentally show that the low bound of the direct SI-traceable microwave electric field is extended by two orders of magnitude, which is from several mV/cm to $\ensuremath{\mu}\mathrm{V}/\mathrm{cm}$ in a room-temperate Rb cell with a modest setup.

Physical Review A•Jun 24, 2021•68 citations

Electric field metrology for SI traceability: Systematic measurement uncertainties in electromagnetically induced transparency in atomic vapor

Christopher L. Holloway, Matthew T. Simons, Joshua A. Gordon +3 more

We investigate the relationship between the Rabi frequency (ΩRF, related to the applied electric field) and Autler-Townes (AT) splitting, when performing atom-based radio-frequency (RF) electric (E) field strength measurements using Rydberg states and electromagnetically induced transparency (EIT) in an atomic vapor. The AT splitting satisfies, under certain conditions, a well-defined linear relationship with the applied RF field amplitude. The EIT/AT-based E-field measurement approach derived from these principles is currently being investigated by several groups around the world as a means to develop a new SI-traceable RF E-field measurement technique. We establish conditions under which the measured AT-splitting is an approximately linear function of the RF electric field. A quantitative description of systematic deviations from the linear relationship is key to exploiting EIT/AT-based atomic-vapor spectroscopy for SI-traceable field measurement. We show that the linear relationship is valid and can be used to determine the E-field strength, with minimal error, as long as the EIT linewidth is small compared to the AT-splitting. We also discuss interesting aspects of the thermal dependence (i.e., hot- versus cold-atom) of this EIT-AT technique. An analysis of the transition from cold- to hot-atom EIT in a Doppler-mismatched cascade system reveals a significant change of the dependence of the EIT linewidth on the optical Rabi frequencies and of the AT-splitting on ΩRF.

Journal of Applied Physics•Jun 20, 2017•247 citations

Measurement of microwave electric field based on electromagnetically induced transparency by using cold Rydberg atoms

Fei Zhou, Feng-Dong Jia, Xiubin Liu +3 more

Microwave electric fields are measured by using cold Rydberg atoms. We obtain spindle-shaped cold atomic clouds in a magneto-optical trap and then pump the cold atoms to quantum state 5S1/2, F = 2, mF = 2 by using an optical-pump laser. We obtain the Rydberg electromagnetic induction transparency (EIT) spectrum peak with narrow linewidth by the low temperature and small residual Doppler broadening. The results show that the typical EIT linewidth with 16 μK cold atoms is about 460 kHz which is 15 times narrower than that of 7 MHz obtained in the thermal vapor cell. The microwave electric field amplitude is measured by Autler-Townes splitting (EIT-AT splitting) in the cold atoms at frequencies of 9.2, 14.2 and 22.1 GHz, receptively. The results show that there is a good linear relationship between the EIT-AT splitting interval and the microwave electric field amplitude. The lower limit of the microwave electric field amplitude that can be measured in the linear region can reach as low as 222 μV/cm, which is about 22 times larger than the lower limit in the traditional thermal vapor cell about of 5 mV/cm. The improvement of the lower limit by EIT-AT splitting method is roughly proportional to the narrowing EIT line width by cold atom samples. This demonstrates that benefiting from the smaller residual Doppler effect and the narrower EIT linewidth in cold atoms, the cold atom system is more advantageous in the experimental measuring of the weak microwave electric field amplitude by using the EIT-AT splitting method. This is of great benefit to the absolute calibration of very weak microwave electric fields. Furthermore, the lower limit of the microwave electric field amplitude that can be measured is smaller than 1 μV/cm by using the change of transmittance of the prober laser at the EIT resonance, and the corresponding sensitivity can reach 1 μV·cm–1·Hz–1/2. These results demonstrate the advantages of cold atomic sample in microwave electric field measurement and its absolute calibration.

Acta Physica Sinica•Dec 9, 2022•5 citations

Simultaneously measuring microwave electric fields at different frequencies by Rydberg-atom-based electrometry with Zeeman-resolved Autler–Townes splitting

Yuxiang Wang, Yuqing Liu, Qianyi Zhang +5 more

We provide the simultaneous traceable measurements of microwave electric fields at two different frequencies by the electromagnetically induced transparency (EIT) and Autler–Townes (AT) splitting. A static magnetic field working together with a linearly polarized probe and coupling light prepares Rydberg atoms in Zeeman sublevels with maximal |mJ| in an atomic vapor cell. Using the EIT-AT splitting of these two maximal |mJ| states, the microwave electric fields at two different frequencies are simultaneously measured, in which their frequency difference can be adjustable within the linear range of magnetic field-induced level shifts. The proposed method provides a promising prospect for calibrating multiple microwave frequencies simultaneously in the future.

AIP Advances•Oct 1, 2024•4 citations

Rydberg-atom-based electrometry

Huang Wei, Liang Zhen-Tao, Du Yan-Xiong +2 more

Atom in Rydberg state has large polarizability, large electric dipole and low ionization threshold field. It is very sensitive to electric field, therefore it can be used to measure the amplitude of electric field, especially the microwave electric field. The new developed scheme is based on quantum interference effects (electromagnetically induced transparency and Autler-Townes splitting) in Rydberg atoms. Instead of the direct amplitude measurement, this method tests the Rabi frequency value of the transmission spectrum which is determined by the microwave electric field strength and the corresponding atom nature. The minimum measured strengths of microwave electric fields are far below the standard values obtained by traditional antenna methods. Compared with the traditional methods, this new scheme has several advantages, such as self-calibration, non-perturbation to the measured field and independence of the probe length. Besides, this scheme can also be used to measure the polarization direction of microwave electric field and realize sub-wavelength imaging. Through adjusting the wavelength of coupling laser, a broadband 1-500 GHz microwave electric field measurement can be achieved. This new scheme is benefitial to conducting the continue electric field measurement and the miniaturization of the test equipment. In this paper, the researches about using Rydberg atom to measure electric field with high precision are reviewed. The basic theory and experimental techniques are introduced. Finally, we discuss a promising method of using Rydberg atom interferometer to detect the accumulated phase in the process of interaction between electric field and Rydberg atoms. This method converts amplitude measurement into phase test, which may improve the precision and sensitivity.

Acta Physica Sinica•Jan 1, 2015•15 citations

Microwave Electric Field Measurement Based on Electromagnetically-Induced Transparency and Absorption in Atomic Vapor Cell at Room Temperature

Xiaohong Liu, Jie Liang, Changjun Chen +2 more

The traceability of microwave electric field is measured based on the Rydberg atomic quantum interference effect. The rubidium atomic vapor cell at room temperature is used as the probe, and the Autler-Townes splitting of two-photon electromagnetically-induced transparency, three-photon electromagnetically-induced transparency and three-photon electromagnetically-induced absorption effect are analyzed theoretically. The measurement limit of atomic shot noise is also discussed. This method is not only suitable for the traceability and self-calibration measurement of the microwave electric field but also for the sub-wavelength imaging and vector measurement of the microwave electric field and will provide a reference for further miniaturization and integration of the atomic microwave probe.

华南师范大学学报（自然科学版）•Jun 25, 2020•0 citations
The atom-based traceable standard for microwave electrometry shows promising advantages by enabling stable and uniform measurement. Here we theoretically propose and then experimentally realize an alternative direct International System of Units (SI)--traceable and self-calibrated method for measuring a microwave-electric-field strength based on electromagnetically induced absorption (EIA) in cold Rydberg atoms. Comparing with the method of electromagnetically induced transparency, we show that the equivalence relation between the microwave Rabi frequency and Autler-Townes splitting is more valid and is even more robust against the experimental parameters in the EIA's linear region. Furthermore, a narrower linewidth of cold Rydberg EIA enables us to realize a direct SI-traceable microwave-electric-field measurement as small as \ensuremath∼100\ensuremathμVcm\ensuremath−1\ensuremath{\sim}100\phantom{\rule{4pt}{0ex}}\ensuremath{\mu}\mathrm{V}\phantom{\rule{0.16em}{0ex}}{\mathrm{cm}}^{\ensuremath{-}1}\ensuremath∼100\ensuremathμVcm\ensuremath−1.
The Rydberg electromagnetically induced transparency (EIT)--Autler Townes (AT) splitting proportional to the target microwave electric field strength is an atom-based primary traceable standard in microwave electrometry. The minimum detected microwave electric field is limited when the EIT-AT splitting is indistinguishable. We design a method for auxiliary microwave-dressed Rydberg atoms that extends the electrometric span. We theoretically and experimentally show that the low bound of the direct SI-traceable microwave electric field is extended by two orders of magnitude, which is from several mV/cm to $\ensuremath{\mu}\mathrm{V}/\mathrm{cm}$ in a room-temperate Rb cell with a modest setup.
We investigate the relationship between the Rabi frequency (ΩRF, related to the applied electric field) and Autler-Townes (AT) splitting, when performing atom-based radio-frequency (RF) electric (E) field strength measurements using Rydberg states and electromagnetically induced transparency (EIT) in an atomic vapor. The AT splitting satisfies, under certain conditions, a well-defined linear relationship with the applied RF field amplitude. The EIT/AT-based E-field measurement approach derived from these principles is currently being investigated by several groups around the world as a means to develop a new SI-traceable RF E-field measurement technique. We establish conditions under which the measured AT-splitting is an approximately linear function of the RF electric field. A quantitative description of systematic deviations from the linear relationship is key to exploiting EIT/AT-based atomic-vapor spectroscopy for SI-traceable field measurement. We show that the linear relationship is valid and can be used to determine the E-field strength, with minimal error, as long as the EIT linewidth is small compared to the AT-splitting. We also discuss interesting aspects of the thermal dependence (i.e., hot- versus cold-atom) of this EIT-AT technique. An analysis of the transition from cold- to hot-atom EIT in a Doppler-mismatched cascade system reveals a significant change of the dependence of the EIT linewidth on the optical Rabi frequencies and of the AT-splitting on ΩRF.
Microwave electric fields are measured by using cold Rydberg atoms. We obtain spindle-shaped cold atomic clouds in a magneto-optical trap and then pump the cold atoms to quantum state 5S1/2, F = 2, mF = 2 by using an optical-pump laser. We obtain the Rydberg electromagnetic induction transparency (EIT) spectrum peak with narrow linewidth by the low temperature and small residual Doppler broadening. The results show that the typical EIT linewidth with 16 μK cold atoms is about 460 kHz which is 15 times narrower than that of 7 MHz obtained in the thermal vapor cell. The microwave electric field amplitude is measured by Autler-Townes splitting (EIT-AT splitting) in the cold atoms at frequencies of 9.2, 14.2 and 22.1 GHz, receptively. The results show that there is a good linear relationship between the EIT-AT splitting interval and the microwave electric field amplitude. The lower limit of the microwave electric field amplitude that can be measured in the linear region can reach as low as 222 μV/cm, which is about 22 times larger than the lower limit in the traditional thermal vapor cell about of 5 mV/cm. The improvement of the lower limit by EIT-AT splitting method is roughly proportional to the narrowing EIT line width by cold atom samples. This demonstrates that benefiting from the smaller residual Doppler effect and the narrower EIT linewidth in cold atoms, the cold atom system is more advantageous in the experimental measuring of the weak microwave electric field amplitude by using the EIT-AT splitting method. This is of great benefit to the absolute calibration of very weak microwave electric fields. Furthermore, the lower limit of the microwave electric field amplitude that can be measured is smaller than 1 μV/cm by using the change of transmittance of the prober laser at the EIT resonance, and the corresponding sensitivity can reach 1 μV·cm–1·Hz–1/2. These results demonstrate the advantages of cold atomic sample in microwave electric field measurement and its absolute calibration.
We provide the simultaneous traceable measurements of microwave electric fields at two different frequencies by the electromagnetically induced transparency (EIT) and Autler–Townes (AT) splitting. A static magnetic field working together with a linearly polarized probe and coupling light prepares Rydberg atoms in Zeeman sublevels with maximal |mJ| in an atomic vapor cell. Using the EIT-AT splitting of these two maximal |mJ| states, the microwave electric fields at two different frequencies are simultaneously measured, in which their frequency difference can be adjustable within the linear range of magnetic field-induced level shifts. The proposed method provides a promising prospect for calibrating multiple microwave frequencies simultaneously in the future.
Atom in Rydberg state has large polarizability, large electric dipole and low ionization threshold field. It is very sensitive to electric field, therefore it can be used to measure the amplitude of electric field, especially the microwave electric field. The new developed scheme is based on quantum interference effects (electromagnetically induced transparency and Autler-Townes splitting) in Rydberg atoms. Instead of the direct amplitude measurement, this method tests the Rabi frequency value of the transmission spectrum which is determined by the microwave electric field strength and the corresponding atom nature. The minimum measured strengths of microwave electric fields are far below the standard values obtained by traditional antenna methods. Compared with the traditional methods, this new scheme has several advantages, such as self-calibration, non-perturbation to the measured field and independence of the probe length. Besides, this scheme can also be used to measure the polarization direction of microwave electric field and realize sub-wavelength imaging. Through adjusting the wavelength of coupling laser, a broadband 1-500 GHz microwave electric field measurement can be achieved. This new scheme is benefitial to conducting the continue electric field measurement and the miniaturization of the test equipment. In this paper, the researches about using Rydberg atom to measure electric field with high precision are reviewed. The basic theory and experimental techniques are introduced. Finally, we discuss a promising method of using Rydberg atom interferometer to detect the accumulated phase in the process of interaction between electric field and Rydberg atoms. This method converts amplitude measurement into phase test, which may improve the precision and sensitivity.
The traceability of microwave electric field is measured based on the Rydberg atomic quantum interference effect. The rubidium atomic vapor cell at room temperature is used as the probe, and the Autler-Townes splitting of two-photon electromagnetically-induced transparency, three-photon electromagnetically-induced transparency and three-photon electromagnetically-induced absorption effect are analyzed theoretically. The measurement limit of atomic shot noise is also discussed. This method is not only suitable for the traceability and self-calibration measurement of the microwave electric field but also for the sub-wavelength imaging and vector measurement of the microwave electric field and will provide a reference for further miniaturization and integration of the atomic microwave probe.