Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:1909.05810 · Physical Review Applied

Sideband-Enhanced Cold Atomic Source for Optical Clocks

Matteo Barbiero, Marco G. Tarallo, Davide Calonico, Filippo Levi, Giacomo Lamporesi, Gabriele Ferrari

Published Jan 9, 2020• 43 citations
arXivHTMLPDF

Abstract

We demonstrate the enhancement and optimization of a cold strontium atomic beam from a two-dimensional magneto-optical trap (2D MOT) transversely loaded from a collimated atomic beam by adding a sideband frequency to the cooling laser. The parameters of the cooling and sideband beams are scanned to achieve the maximum atomic beam flux and are compared with Monte Carlo simulations. We obtain a 2.3 times larger total atomic flux and a brightness increase of a factor 4 compared with a conventional, single-frequency 2D MOT for a given total power of 200 mW. We show that the sideband-enhanced 2D MOT can reach the loading-rate performances of space-demanding Zeeman-slower-based systems, while it can overcome systematic effects due to thermal-beam collisions and hot-black-body-radiation shift, making it suitable for both transportable and accurate optical lattice clocks. Finally, we numerically study possible extensions of the sideband-enhanced 2D MOT to other alkaline-earth species.

DOI
10.1103/physrevapplied.13.014013

Related papers

Optimized atomic flux from a frequency-modulated two-dimensional magneto-optical trap for cold fermionic potassium atoms

Jae Hoon Lee, Jongchul Mun

We present our study on enhancement and optimization of potassium-40 (K40) atomic beam flux from a two-dimensional magneto-optical trap (2D MOT) by modulating the frequency of cooling laser. The laser cooling beam frequencies of the 2D MOT were effectively broadened via electro-optical modulators at 10 MHz, with a modulation index ranging from β=0 to 7, depending on the laser intensity. Laser parameters of the 2D MOT beams and the magnetic field gradient were scanned for optimal settings for maximum atomic beam flux. When compared to a conventional 2D MOT with fixed laser frequencies, we were able to obtain a 3.7 times enhancement of the atomic flux when the total laser power was 640 mW. Numerical calculations predict further improvement for higher laser beam intensities.

Journal of the Optical Society of America B•Jun 12, 2017•8 citations

Two-dimensional magneto-optical trap as a source for cold strontium atoms

Ingo Nosske, Luc Couturier, Fachao Hu +6 more

We report on the realization of a transversely loaded two-dimensional magneto-optical trap serving as a source for cold strontium atoms. We analyze the dependence of the source's properties on various parameters, in particular the intensity of a pushing beam accelerating the atoms out of the source. An atomic flux exceeding ${10}^{9}\phantom{\rule{0.28em}{0ex}}\mathrm{atoms}/\mathrm{s}$ at a rather moderate oven temperature of $500{\phantom{\rule{0.16em}{0ex}}}^{\ensuremath{\circ}}\mathrm{C}$ is achieved. The longitudinal velocity of the atomic beam can be tuned over several tens of m/s by adjusting the power of the pushing laser beam. The beam divergence is around 60 mrad, determined by the transverse velocity distribution of the cold atoms. The slow atom source is used to load a three-dimensional magneto-optical trap realizing loading rates up to ${10}^{9}\phantom{\rule{0.16em}{0ex}}\mathrm{atoms}/\mathrm{s}$ without indication of saturation of the loading rate for increasing oven temperature. The compact setup avoids undesired effects found in alternative sources like, e.g., Zeeman slowers, such as vacuum contamination and black-body radiation due to the hot strontium oven.

Physical Review A•Nov 15, 2017•56 citations

Enhanced cold mercury atom production with two-dimensional magneto-optical trap

Ye Zhang, Qixin Liu, Jianfang Sun +2 more

A cold atom source is important for quantum metrology and precision measurement. To reduce the quantum projection noise limit in optical lattice clock, one can increase the number of cold atoms and reduce the dead time by enhancing the loading rate. In this work, we realize an enhanced cold mercury atom source based on a two-dimensional (2D) magneto-optical trap (MOT). The vacuum system is composed of two titanium chambers connected with a differential pumping tube. Two stable cooling laser systems are adopted for the 2D-MOT and the three-dimensional (3D)-MOT, respectively. Using an optimized 2D-MOT and push beam, about 1.3×106 atoms, which are almost an order of magnitude higher than using a pure 3D-MOT, are loaded into the 3D-MOT for 202Hg atoms. This enhanced cold mercury atom source is helpful in increasing the frequency stability of a neutral mercury lattice clock.

Chinese Physics B•Feb 10, 2022•7 citations

An integrated high-flux cold atomic beam source for strontium

Jie Li, Zhi-Peng Jia, Peng Liu +8 more

We present the design, construction, and characterization of an integrated cold atomic beam source for strontium (Sr), which is based on a compact Zeeman slower for slowing the thermal atomic beam and an atomic deflector for selecting the cold flux. By adopting arrays of permanent magnets to produce the magnetic fields of the slower and the deflector, we effectively reduce the system size and power compared to traditional systems with magnetic coils. After the slower cooling, one can employ additional transverse cooling in the radial direction and improve the atom collimation. The atomic deflectors employ two stages of two-dimensional magnetic-optical trapping (MOT) to deflect the cold flux, whose atomic speed is lower than 50 m/s, by 20° from the thermal atomic beam. We characterize the cold atomic beam flux of the source by measuring the loading rate of a three-dimensional MOT. The loading rates reach up to 109 atoms/s. The setup is compact, highly tunable, lightweight, and requires low electrical power, which addresses the challenge of reducing the complexity of building optical atomic clocks and quantum simulation devices based on Sr.

Review of Scientific Instruments•Sep 1, 2023•8 citations

High-flux two-dimensional magneto-optical-trap source for cold lithium atoms

T. G. Tiecke, S. D. Gensemer, A. Ludewig +1 more

We demonstrate a two-dimensional magneto-optical trap (2D MOT) as a beam source for cold $^{6}\text{L}\text{i}$ atoms. The source is side loaded from an oven operated at temperatures in the range $600\ensuremath{\lesssim}T\ensuremath{\lesssim}700\text{ }\text{K}$. The performance is analyzed by loading the atoms into a three-dimensional MOT located 220 mm downstream from the source. The maximum recapture rate of $\ensuremath{\sim}{10}^{9}\text{ }{\text{s}}^{\ensuremath{-}1}$ is obtained for $T\ensuremath{\approx}700\text{ }\text{K}$ and results in a total of up to ${10}^{10}$ trapped atoms. The recaptured fraction is estimated to be $30\ifmmode\pm\else\textpm\fi{}10%$ and limited by beam divergence. The most-probable velocity in the beam $({\ensuremath{\alpha}}_{z})$ is varied from 18 to 70 m/s by increasing the intensity of a push beam. The source is quite monochromatic with a full width at half maximum velocity spread of 11 m/s at ${\ensuremath{\alpha}}_{z}=36\text{ }\text{m}/\text{s}$, demonstrating that side loading completely eliminates beam contamination by hot vapor from the oven. We identify depletion of the low-velocity tail of the oven flux as the limiting loss mechanism. Our approach is suitable for other atomic species.

arXiv:0905.1063•Physical Review A•Jul 20, 2009•88 citations

Enhanced Atom Transport in an Ytterbium 2D-MOT with an Off-Axis Push Beam

Ailong TAO, Di Hu, Meifeng Ye +7 more

Abstract We present the first implementation of a slow ytterbium atomic beam source based on a compact two-dimensional magneto-optical trap (2D-MOT) for ytterbium optical clocks. Detailed experiment parameters are optimized through Monte Carlo (MC) simulations and experimentally validated by the loading behavior of the subsequent 3D-MOT. Specifically, theoretical modeling reveals significant asymmetry in atomic beam distribution across the differential pumping channel (DPC), indicating critical dependence of the pre-cooled efficiency on the pushing beam alignment. Numerical simulation shows that a deviation of approximately 5◦ between the pushing beam and the normal incidence axis can effectively mitigate the distribution asymmetry and then enhance the 3D-MOT capture efficiency. Experimental results demonstrate a maximum 3D-MOT loading rate of 1.5×10 8 atoms/s with steady-state atom number exceeding 8×10 7 , fully demonstrating the feasibility of this scheme for ytterbium atoms. The system offers a compact design coupled with significantly reduced power consumption. These inherent features establish a robust platform for developing portable optical clocks and other field-deployable quantum technologies.

Chinese Physics B•Apr 17, 2026•0 citations
We demonstrate the enhancement and optimization of a cold strontium atomic beam from a two-dimensional magneto-optical trap (2D MOT) transversely loaded from a collimated atomic beam by adding a sideband frequency to the cooling laser. The parameters of the cooling and sideband beams are scanned to achieve the maximum atomic beam flux and are compared with Monte Carlo simulations. We obtain a 2.3 times larger total atomic flux and a brightness increase of a factor 4 compared with a conventional, single-frequency 2D MOT for a given total power of 200 mW. We show that the sideband-enhanced 2D MOT can reach the loading-rate performances of space-demanding Zeeman-slower-based systems, while it can overcome systematic effects due to thermal-beam collisions and hot-black-body-radiation shift, making it suitable for both transportable and accurate optical lattice clocks. Finally, we numerically study possible extensions of the sideband-enhanced 2D MOT to other alkaline-earth species.
We present our study on enhancement and optimization of potassium-40 (K40) atomic beam flux from a two-dimensional magneto-optical trap (2D MOT) by modulating the frequency of cooling laser. The laser cooling beam frequencies of the 2D MOT were effectively broadened via electro-optical modulators at 10 MHz, with a modulation index ranging from β=0 to 7, depending on the laser intensity. Laser parameters of the 2D MOT beams and the magnetic field gradient were scanned for optimal settings for maximum atomic beam flux. When compared to a conventional 2D MOT with fixed laser frequencies, we were able to obtain a 3.7 times enhancement of the atomic flux when the total laser power was 640 mW. Numerical calculations predict further improvement for higher laser beam intensities.
We report on the realization of a transversely loaded two-dimensional magneto-optical trap serving as a source for cold strontium atoms. We analyze the dependence of the source's properties on various parameters, in particular the intensity of a pushing beam accelerating the atoms out of the source. An atomic flux exceeding 109atoms/s{10}^{9}\phantom{\rule{0.28em}{0ex}}\mathrm{atoms}/\mathrm{s}109atoms/s at a rather moderate oven temperature of $500{\phantom{\rule{0.16em}{0ex}}}^{\ensuremath{\circ}}\mathrm{C}$ is achieved. The longitudinal velocity of the atomic beam can be tuned over several tens of m/s by adjusting the power of the pushing laser beam. The beam divergence is around 60 mrad, determined by the transverse velocity distribution of the cold atoms. The slow atom source is used to load a three-dimensional magneto-optical trap realizing loading rates up to 109atoms/s{10}^{9}\phantom{\rule{0.16em}{0ex}}\mathrm{atoms}/\mathrm{s}109atoms/s without indication of saturation of the loading rate for increasing oven temperature. The compact setup avoids undesired effects found in alternative sources like, e.g., Zeeman slowers, such as vacuum contamination and black-body radiation due to the hot strontium oven.
A cold atom source is important for quantum metrology and precision measurement. To reduce the quantum projection noise limit in optical lattice clock, one can increase the number of cold atoms and reduce the dead time by enhancing the loading rate. In this work, we realize an enhanced cold mercury atom source based on a two-dimensional (2D) magneto-optical trap (MOT). The vacuum system is composed of two titanium chambers connected with a differential pumping tube. Two stable cooling laser systems are adopted for the 2D-MOT and the three-dimensional (3D)-MOT, respectively. Using an optimized 2D-MOT and push beam, about 1.3×106 atoms, which are almost an order of magnitude higher than using a pure 3D-MOT, are loaded into the 3D-MOT for 202Hg atoms. This enhanced cold mercury atom source is helpful in increasing the frequency stability of a neutral mercury lattice clock.
We present the design, construction, and characterization of an integrated cold atomic beam source for strontium (Sr), which is based on a compact Zeeman slower for slowing the thermal atomic beam and an atomic deflector for selecting the cold flux. By adopting arrays of permanent magnets to produce the magnetic fields of the slower and the deflector, we effectively reduce the system size and power compared to traditional systems with magnetic coils. After the slower cooling, one can employ additional transverse cooling in the radial direction and improve the atom collimation. The atomic deflectors employ two stages of two-dimensional magnetic-optical trapping (MOT) to deflect the cold flux, whose atomic speed is lower than 50 m/s, by 20° from the thermal atomic beam. We characterize the cold atomic beam flux of the source by measuring the loading rate of a three-dimensional MOT. The loading rates reach up to 109 atoms/s. The setup is compact, highly tunable, lightweight, and requires low electrical power, which addresses the challenge of reducing the complexity of building optical atomic clocks and quantum simulation devices based on Sr.
We demonstrate a two-dimensional magneto-optical trap (2D MOT) as a beam source for cold 6Li^{6}\text{L}\text{i}6Li atoms. The source is side loaded from an oven operated at temperatures in the range $600\ensuremath{\lesssim}T\ensuremath{\lesssim}700\text{ }\text{K}$. The performance is analyzed by loading the atoms into a three-dimensional MOT located 220 mm downstream from the source. The maximum recapture rate of $\ensuremath{\sim}{10}^{9}\text{ }{\text{s}}^{\ensuremath{-}1}$ is obtained for $T\ensuremath{\approx}700\text{ }\text{K}$ and results in a total of up to 1010{10}^{10}1010 trapped atoms. The recaptured fraction is estimated to be $30\ifmmode\pm\else\textpm\fi{}10%$ and limited by beam divergence. The most-probable velocity in the beam $({\ensuremath{\alpha}}_{z})$ is varied from 18 to 70 m/s by increasing the intensity of a push beam. The source is quite monochromatic with a full width at half maximum velocity spread of 11 m/s at ${\ensuremath{\alpha}}_{z}=36\text{ }\text{m}/\text{s}$, demonstrating that side loading completely eliminates beam contamination by hot vapor from the oven. We identify depletion of the low-velocity tail of the oven flux as the limiting loss mechanism. Our approach is suitable for other atomic species.
Abstract We present the first implementation of a slow ytterbium atomic beam source based on a compact two-dimensional magneto-optical trap (2D-MOT) for ytterbium optical clocks. Detailed experiment parameters are optimized through Monte Carlo (MC) simulations and experimentally validated by the loading behavior of the subsequent 3D-MOT. Specifically, theoretical modeling reveals significant asymmetry in atomic beam distribution across the differential pumping channel (DPC), indicating critical dependence of the pre-cooled efficiency on the pushing beam alignment. Numerical simulation shows that a deviation of approximately 5◦ between the pushing beam and the normal incidence axis can effectively mitigate the distribution asymmetry and then enhance the 3D-MOT capture efficiency. Experimental results demonstrate a maximum 3D-MOT loading rate of 1.5×10 8 atoms/s with steady-state atom number exceeding 8×10 7 , fully demonstrating the feasibility of this scheme for ytterbium atoms. The system offers a compact design coupled with significantly reduced power consumption. These inherent features establish a robust platform for developing portable optical clocks and other field-deployable quantum technologies.