Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:1811.11741 · New Journal of Physics

Unidirectional frequency conversion in microring resonators for on-chip frequency-multiplexed single-photon sources

Mikkel Heuck, Jacob G. Koefoed, Jesper B. Christensen, Yunhong Ding, Lars H. Frandsen, Karsten K. Rottwitt, Leif Katsuo Oxenløwe

Published Feb 22, 2019• 28 citations
arXivHTMLPDF

Abstract

Microring resonators are attractive for low-power frequency conversion via Bragg-scattering four-wave-mixing due to their comb-like resonance spectrum, which allows resonant enhancement of all four waves while maintaining energy and momentum conservation. However, the symmetry of such mode structures limits the conversion efficiency to 50% due to the equal probability of up- and down-conversion. Here, we demonstrate how two coupled microrings enable highly directional conversion between the spectral modes of one of the rings. An extinction between up- and down-conversion of more than 40 dB is experimentally observed. Based on this method, we propose a design for on-chip multiplexed single-photon sources that probabilistically generate photon pairs across many frequency modes of a ring resonator and subsequently convert them to a single frequency—thereby enabling quasi-deterministic photon emission. Our numerical analysis shows that once a photon is generated, it can be converted and emitted into a wave packet having a 90% overlap with a Gaussian with 99% efficiency for a ratio between intrinsic and coupling quality factors of 400.

DOI
10.1088/1367-2630/ab09a7

Related papers

Quantum frequency conversion and strong coupling of photonic modes using four-wave mixing in integrated microresonators

Z. Vernon, Marco Liscidini, John E. Sipe

Single-photon-level quantum frequency conversion has recently been demonstrated using silicon nitride microring resonators. The resonance enhancement offered by such systems enables high-efficiency translation of quantum states of light across wide frequency ranges at subwatt pump powers. We present a detailed theoretical analysis of the conversion dynamics in these systems and show that they are capable of converting single- and multiphoton quantum states. Analytic formulas for the conversion efficiency, spectral conversion probability density, and pump-power requirements are derived which are in good agreement with previous theoretical and experimental results. We show that with only modest improvement to the state of the art, efficiencies exceeding 95% are achievable using less than 100 mW of pump power. At the critical driving strength that yields maximum conversion efficiency, the spectral conversion probability density is shown to exhibit a flat-topped peak, indicating a range of insensitivity to the spectrum of a single-photon input. Two alternate theoretical approaches are presented to study the conversion dynamics: a dressed-mode approach that yields a better intuitive picture of the conversion process, and a study of the temporal dynamics of the participating modes in the resonator, which uncovers a regime of Rabi-like coherent oscillations of single photons between two different frequency modes. This oscillatory regime arises from the strong coupling of distinct frequency modes mediated by coherent pumps.

arXiv:1606.01582•Physical Review A•Aug 2, 2016•23 citations

Development of a High Performance Resonant Photon-Pair Source in Silicon

Jeffrey A. Steidle

One of the key building blocks of quantum photonic systems is a source of indistinguishable photons. Silicon ring resonators can be used as photon pair sources by taking advantage of silicon's large third order nonlinearity with a process known as spontaneous four wave mixing. These sources are capable of producing pairs of indistinguishable photons but typically suffer from an effective 50% loss. By slightly decoupling the input waveguide from the ring, the desired photons generated in the ring can be directed to the drop port. Thus, the ratio between the coincidences from the drop port and the total number of coincidences from all ports (coincidence efficiency) can be significantly increased, with the trade-off being that the pump is less efficiently coupled into the ring. This asymmetric coupling scheme was used to demonstrate a dual-bus microring source with a coincidence efficiency of ~96%. Unfortunately, the penalty to pump power was quite large, with a required ~10x increase in the pump power to maintain the same pair generation rate.\nTo further improve upon this result, a microring source was designed with multipoint evanescent couplers to induce a strong spectral dependence in the coupling coefficients. This coupler design can be used on both sides of the ring resonator so that resonances supported by one of the couplers are suppressed by the other. This is the ideal configuration for a ring-based photon-pair source as it can only support the pump photons at the input side while only allowing the generated photons to leave through the output side. Asymmetric coupling was also used in this configuration but in a different way than in the previous source. In this case, the input side of the ring was configured to be critically coupled for maximal resonance enhancement while the output side was configured to be over coupled to minimize photon-pair loss within the ring. This device design was used to demonstrate a photon-pair source with coincidence efficiencies of 0.9981+-6.425x10^-4 and 0.9979+-1.665x10^-3 for degenerate and non-degenerate pump configuration respectively.\nIn addition to the source development, work was done to move some of the pump rejection filtering onto the photonic chip. While the fabricated device only exhibited an extinction of 50 dB, the root cause of the limited extinction was explored and a new filter design was proposed to overcome these limitations. With the combination of the microring source with its greatly improved efficiency and the movement toward reducing the required off-chip filtering, this work represents a significant advancement in the scalability of integrated quantum photonic systems which can enable high performance quantum computing and communication systems.

•Jan 1, 2019•0 citations

Frequency Conversion of a Quantum Dot Single-Photon Source on a Nanophotonic Chip

Anshuman Singh, Qing Li, Jin Liu +3 more

We report frequency conversion of single photons from a quantum dot using four-wave-mixing Bragg scattering in a Si3N4 microring. We measure an on-chip conversion efficiency >10%, and frequency-converted light that is antibunched with g(2)(0) <0.5.

Conference on Lasers and Electro-Optics•Jan 1, 2018•1 citation

Generation of Entangled Photon Pairs from High-Quality-Factor Silicon Microring Resonator at Near-Zero Anomalous Dispersion

Muneeb Farooq, Francisco M. Soares, Francisco Diaz

The intrinsic third-order nonlinearity in silicon has proven it to be quite useful in the field of quantum optics. Silicon is suitable for producing time-correlated photon pairs that are sources of heralded single-photon states for quantum integrated circuits. A quantum signal source in the form of single photons is an inherent requirement for the principles of quantum key distribution technology for secure communications. Here, we present numerical simulations of a silicon ring with a 6 μ m radius side-coupled with a bus waveguide as the source for the generation of single photons. The photon pairs are generated by exploring the process of degenerate spontaneous four-wave mixing (SFWM). The free spectral range (FSR) of the ring is quite large, simplifying the extraction of the signal/idler pairs. The phase-matching condition is considered by studying relevant parameters like the dispersion and nonlinearity. We optimize the ring for a high quality factor by varying the gap between the bus and the ring waveguide. This is the smallest ring studied for photon pair generation with a quality factor in the order of 10 5 . The width of the waveguides is chosen such that the phase-matching condition is satisfied, allowing for the propagation of fundamental modes only. The bus waveguide is pumped at one of the ring resonances with the minimum dispersion (1543.5 nm in our case) to satisfy the principle of energy conservation. The photon pair generation rate achieved is comparable to the state of the art. The photon pair sources exploiting nonlinear frequency conversion/generation processes is a promising alternative to atom-like single-photon emitters in the field of integrated photonics. Such miniaturized structures will benefit future on-chip architectures where multiple single-photon source devices are required on the same chip.

•Nov 21, 2024•0 citations

Frequency multiplexing for quasi-deterministic heralded single-photon sources

Chaitali Joshi, Alessandro Farsi, Stéphane Clemmen +2 more

Abstract Parametric single-photon sources are well suited for large-scale quantum networks due to their potential for photonic integration. Active multiplexing of photons can overcome the intrinsically probabilistic nature of these sources, resulting in near-deterministic operation. However, previous implementations using spatial and temporal multiplexing scale unfavorably due to rapidly increasing switching losses. Here, we break this limitation via frequency multiplexing in which switching losses remain fixed irrespective of the number of multiplexed modes. We use low-noise optical frequency conversion for efficient frequency switching and demonstrate multiplexing of three modes. We achieve a generation rate of 4.6 × 104 photons per second with an ultra-low g(2)(0) = 0.07 indicating high single-photon purity. Our scalable, all-fiber multiplexing system has a total loss of just 1.3 dB, such that the 4.8 dB multiplexing enhancement markedly overcomes switching loss. Our approach offers a promising path to creating a deterministic photon source on an integrated chip-based platform.

arXiv:1707.00048•Nature Communications•Feb 21, 2018•157 citations

Silicon Microring Resonator Design with a Dispersive Directional Coupler for Spectrally Pure Photon Sources

Arnab Goswami, Bijoy Krishna Das

Heralded single photon sources generated through spontaneous four wave mixing in silicon microring resonators are highly demanding for large-scale integrated quantum photonics. However, the spectral purity of conventional microring resonators is limited to 93%, which impacts the quality of quantum interference within photonic circuits. The wavelength dependent coupling between ring and bus waveguides plays a significant role in the generation/heralding of single photons from the resonator. In this letter, we have presented a detailed investigation of the dispersive nature of relatively long directional couplers in order to design a microring resonator in all-pass configuration for chip-scale generation of single photons with maximum purity. In our studies, we have shown that a photon purity level close to 99% (λ ∼ 1550 nm) can be achieved by the use of a dispersive directional coupler in a race-track microring resonator in all-pass configuration, without affecting the photon heralding rate. The design parameters of the device are optimized such that it can be fabricated in commercial CMOS foundries.

•May 6, 2025•0 citations
Microring resonators are attractive for low-power frequency conversion via Bragg-scattering four-wave-mixing due to their comb-like resonance spectrum, which allows resonant enhancement of all four waves while maintaining energy and momentum conservation. However, the symmetry of such mode structures limits the conversion efficiency to 50% due to the equal probability of up- and down-conversion. Here, we demonstrate how two coupled microrings enable highly directional conversion between the spectral modes of one of the rings. An extinction between up- and down-conversion of more than 40 dB is experimentally observed. Based on this method, we propose a design for on-chip multiplexed single-photon sources that probabilistically generate photon pairs across many frequency modes of a ring resonator and subsequently convert them to a single frequency—thereby enabling quasi-deterministic photon emission. Our numerical analysis shows that once a photon is generated, it can be converted and emitted into a wave packet having a 90% overlap with a Gaussian with 99% efficiency for a ratio between intrinsic and coupling quality factors of 400.
Single-photon-level quantum frequency conversion has recently been demonstrated using silicon nitride microring resonators. The resonance enhancement offered by such systems enables high-efficiency translation of quantum states of light across wide frequency ranges at subwatt pump powers. We present a detailed theoretical analysis of the conversion dynamics in these systems and show that they are capable of converting single- and multiphoton quantum states. Analytic formulas for the conversion efficiency, spectral conversion probability density, and pump-power requirements are derived which are in good agreement with previous theoretical and experimental results. We show that with only modest improvement to the state of the art, efficiencies exceeding 95% are achievable using less than 100 mW of pump power. At the critical driving strength that yields maximum conversion efficiency, the spectral conversion probability density is shown to exhibit a flat-topped peak, indicating a range of insensitivity to the spectrum of a single-photon input. Two alternate theoretical approaches are presented to study the conversion dynamics: a dressed-mode approach that yields a better intuitive picture of the conversion process, and a study of the temporal dynamics of the participating modes in the resonator, which uncovers a regime of Rabi-like coherent oscillations of single photons between two different frequency modes. This oscillatory regime arises from the strong coupling of distinct frequency modes mediated by coherent pumps.
One of the key building blocks of quantum photonic systems is a source of indistinguishable photons. Silicon ring resonators can be used as photon pair sources by taking advantage of silicon's large third order nonlinearity with a process known as spontaneous four wave mixing. These sources are capable of producing pairs of indistinguishable photons but typically suffer from an effective 50% loss. By slightly decoupling the input waveguide from the ring, the desired photons generated in the ring can be directed to the drop port. Thus, the ratio between the coincidences from the drop port and the total number of coincidences from all ports (coincidence efficiency) can be significantly increased, with the trade-off being that the pump is less efficiently coupled into the ring. This asymmetric coupling scheme was used to demonstrate a dual-bus microring source with a coincidence efficiency of ~96%. Unfortunately, the penalty to pump power was quite large, with a required ~10x increase in the pump power to maintain the same pair generation rate.\nTo further improve upon this result, a microring source was designed with multipoint evanescent couplers to induce a strong spectral dependence in the coupling coefficients. This coupler design can be used on both sides of the ring resonator so that resonances supported by one of the couplers are suppressed by the other. This is the ideal configuration for a ring-based photon-pair source as it can only support the pump photons at the input side while only allowing the generated photons to leave through the output side. Asymmetric coupling was also used in this configuration but in a different way than in the previous source. In this case, the input side of the ring was configured to be critically coupled for maximal resonance enhancement while the output side was configured to be over coupled to minimize photon-pair loss within the ring. This device design was used to demonstrate a photon-pair source with coincidence efficiencies of 0.9981+-6.425x10^-4 and 0.9979+-1.665x10^-3 for degenerate and non-degenerate pump configuration respectively.\nIn addition to the source development, work was done to move some of the pump rejection filtering onto the photonic chip. While the fabricated device only exhibited an extinction of 50 dB, the root cause of the limited extinction was explored and a new filter design was proposed to overcome these limitations. With the combination of the microring source with its greatly improved efficiency and the movement toward reducing the required off-chip filtering, this work represents a significant advancement in the scalability of integrated quantum photonic systems which can enable high performance quantum computing and communication systems.
The intrinsic third-order nonlinearity in silicon has proven it to be quite useful in the field of quantum optics. Silicon is suitable for producing time-correlated photon pairs that are sources of heralded single-photon states for quantum integrated circuits. A quantum signal source in the form of single photons is an inherent requirement for the principles of quantum key distribution technology for secure communications. Here, we present numerical simulations of a silicon ring with a 6 μ m radius side-coupled with a bus waveguide as the source for the generation of single photons. The photon pairs are generated by exploring the process of degenerate spontaneous four-wave mixing (SFWM). The free spectral range (FSR) of the ring is quite large, simplifying the extraction of the signal/idler pairs. The phase-matching condition is considered by studying relevant parameters like the dispersion and nonlinearity. We optimize the ring for a high quality factor by varying the gap between the bus and the ring waveguide. This is the smallest ring studied for photon pair generation with a quality factor in the order of 10 5 . The width of the waveguides is chosen such that the phase-matching condition is satisfied, allowing for the propagation of fundamental modes only. The bus waveguide is pumped at one of the ring resonances with the minimum dispersion (1543.5 nm in our case) to satisfy the principle of energy conservation. The photon pair generation rate achieved is comparable to the state of the art. The photon pair sources exploiting nonlinear frequency conversion/generation processes is a promising alternative to atom-like single-photon emitters in the field of integrated photonics. Such miniaturized structures will benefit future on-chip architectures where multiple single-photon source devices are required on the same chip.
Abstract Parametric single-photon sources are well suited for large-scale quantum networks due to their potential for photonic integration. Active multiplexing of photons can overcome the intrinsically probabilistic nature of these sources, resulting in near-deterministic operation. However, previous implementations using spatial and temporal multiplexing scale unfavorably due to rapidly increasing switching losses. Here, we break this limitation via frequency multiplexing in which switching losses remain fixed irrespective of the number of multiplexed modes. We use low-noise optical frequency conversion for efficient frequency switching and demonstrate multiplexing of three modes. We achieve a generation rate of 4.6 × 104 photons per second with an ultra-low g(2)(0) = 0.07 indicating high single-photon purity. Our scalable, all-fiber multiplexing system has a total loss of just 1.3 dB, such that the 4.8 dB multiplexing enhancement markedly overcomes switching loss. Our approach offers a promising path to creating a deterministic photon source on an integrated chip-based platform.
Heralded single photon sources generated through spontaneous four wave mixing in silicon microring resonators are highly demanding for large-scale integrated quantum photonics. However, the spectral purity of conventional microring resonators is limited to 93%, which impacts the quality of quantum interference within photonic circuits. The wavelength dependent coupling between ring and bus waveguides plays a significant role in the generation/heralding of single photons from the resonator. In this letter, we have presented a detailed investigation of the dispersive nature of relatively long directional couplers in order to design a microring resonator in all-pass configuration for chip-scale generation of single photons with maximum purity. In our studies, we have shown that a photon purity level close to 99% (λ ∼ 1550 nm) can be achieved by the use of a dispersive directional coupler in a race-track microring resonator in all-pass configuration, without affecting the photon heralding rate. The design parameters of the device are optimized such that it can be fabricated in commercial CMOS foundries.