Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:1706.06137 · Applied Physics Letters

A low-power reversible alkali atom source

Songbai Kang, Russell P. Mott, Kevin A. Gilmore, Logan D. Sorenson, Matthew T. Rakher, Elizabeth A. Donley, John E. Kitching, Christopher S. Roper

Published Jun 12, 2017• 22 citations
arXivHTMLPDF

Abstract

An electrically controllable, solid-state, reversible device for sourcing and sinking alkali vapor is presented. When placed inside an alkali vapor cell, both an increase and decrease in the rubidium vapor density by a factor of two are demonstrated through laser absorption spectroscopy on 10–15 s time scales. The device requires low voltage (5 V), low power (<3.4 mW peak power), and low energy (<10.7 mJ per 10 s pulse). The absence of oxygen emission during operation is shown through residual gas analysis, indicating that Rb is not lost through chemical reaction but rather by ion transport through the designed channel. This device is of interest for atomic physics experiments and, in particular, for portable cold-atom systems where dynamic control of alkali vapor density can enable advances in science and technology.

DOI
10.1063/1.4986197

Related papers

Magneto-optic trap using a reversible, solid-state alkali-metal source

S. Kang, K. R. Moore, J. P. McGilligan +5 more

We demonstrate a novel way to form and deplete a vapor-cell magneto-optic trap (MOT) using a reversible, solid-state alkali-metal source via an applied polarized voltage. Using ∼100 mW of electrical power, a trapped-atom number of 5×106 has been achieved, starting from near zero and the timescales of the MOT formation and depletion of ∼1 s. This fast, reversible, and low-power alkali-atom source is desirable in both tabletop and portable cold-atom systems. The core technology of this device should translate readily to other alkali and alkaline-earth elements that could find a wide range of uses in cold-atom systems and instruments.

arXiv:1901.09186•Optics Letters•Jun 5, 2019•22 citations

A low-power, electrically-controllable alkali source for cold-atom microsystems

Songbai Kang, Russell P. Mott, Kevin Gilmore +5 more

We develop a low-power, solid-state electrochemical alkali source. Vapor-phase sinking and sourcing of Rb atoms have been demonstrated with just 5 V opposite-polarity voltages. The device is of considerable interest for cold-atom microsystems.

Frontiers in Optics•Jan 1, 2017•0 citations

Dynamic Characterization of an Alkali-Ion Battery as a Source for Laser-Cooled Atoms

J. P. McGilligan, Kaitlin Moore, S. Kang +5 more

We investigate a solid-state reversible alkali-ion battery (AIB) capable of regulating the density of alkali atoms in a vacuum system used for the production of laser-cooled atoms. The cold-atom sample can be used with in-vacuum chronoamperometry as a diagnostic for the voltage-controlled electrochemical reaction that sources or sinks alkali atoms into the vapor. In a combined reaction-diffusion-limited regime, we show that the number of laser-cooled atoms in a magneto-optical trap can be increased both by initially loading the AIB from the vapor for longer and by using higher voltages across the AIB when atoms are subsequently sourced back into the vapor. The time constants associated with the change in atom number in response to a change in AIB voltage are in the range of 0.5--40 s. The AIB alkali reservoir is demonstrated to survive oxidization during atmospheric exposure, simplifying reservoir loading prior to vacuum implementation as a replacement for traditional resistively heated dispensers. The AIB capabilities may provide an improved atom-number stability in next-generation atomic clocks and sensors, while also facilitating fast loading and increased interrogation times.

arXiv:1908.06898•Physical Review Applied•Apr 14, 2020•18 citations

Active stabilization of alkali-atom vapor density with a solid-state electrochemical alkali-atom source

Songbai Kang, Russell P. Mott, Allison V. Mis +3 more

). Active stabilization with this device is of high interest for portable cold-atom microsystems where large ambient temperature working ranges and low power consumption are required.

Optics Express•Feb 2, 2018•10 citations

Microfabricated Alkali Atom Vapor Cells for Chip Scale Atomic Clock

M.-Z. Huang, Jiashan Zhu, Guangfeng Shi +2 more

In this paper we present a novel fabrication technique for coherent population trapping based chip-sized alkali vapor cells. There are two cavities in the cell design, one is a reaction cavity for alkali dispenser and the other one is a working cavity for alkali storage. An alkali dispenser pill is placed in the reaction cavity and subsequently reacted to obtain pure alkali material. The alkali atoms can be transferred into the working cavity in vapor form once the cell is heated up to 70 degree. Since alkali reacts with many materials and cannot be handled in air, our method provides a low cost and high reproducible way to fabricate highly miniaturized vapor cells. Silicon micromachining and glass-Si-glass three-layer anodic bonding technology is applied to introduce alkali atoms and a buffer gas into the cell and effectively seal this environment within the cell. A rubidium vapor cell is demonstrated using our design. The cell size is 5×4×1.6 mm 3 , with hermetic seal leakage <5e −9 atm cc/s. Modulated optical absorption spectrum of the cell is obtained and matched with pure rubidium atom, indicating the suitability of these cells for use in highly miniaturized atomic frequency references based on CPT excitation scheme. In addition, the entire process is fabricated at the wafer level, with subsequent dicing into individual cells.

Annual Conference of the Chinese Society of Micro-Nano Technology (CSMNT)•Nov 22, 2017•0 citations

Preparation of microfabricated alkali atomic vapor cells with good hermeticity

Yali Liu, Wei Li

The microfabricated alkali atomic vapor cells are essential for the chip scale quantum sensing instruments which provide a robust, simple platform for precision measurement for a quantum system. In order to solve the problems of difficult quantitative filling of alkali atoms and poor hermeticity in the fabricated process of the cells, the preparation of microfabricated alkali atomic vapor cells with good hermeticity is studied. The cells are fabricated by the microelectromechanical system (MEMS) technology. Rubidium (Rb) atomic vapor cells with nitrogen (N 2 ) as buffer gas are successfully obtained by photolysis of rubidium azide (RbN 3 ), which is confirmed by the presence of Rb vapor in the cells through absorption spectroscopy for the 5S 1/2 → 5P 3/2 and 5S 1/2 → 5P 1/2 transitions in Rb atoms at 780 nm and 795 nm. The influences of filling amount and baking temperature of RbN 3 solution on the hermeticity of the microfabricated atomic vapor cells are demonstrated. Also, the influences of filling amount of Rb atoms and temperature on the absorption spectrum intensities of Rb vapor in the cells are studied through a theoretical analysis. This research provides a reference for the design and preparation of high quality microfabricated alkali atomic vapor cells.

Measurement Sensors•Feb 17, 2025•1 citation
An electrically controllable, solid-state, reversible device for sourcing and sinking alkali vapor is presented. When placed inside an alkali vapor cell, both an increase and decrease in the rubidium vapor density by a factor of two are demonstrated through laser absorption spectroscopy on 10–15 s time scales. The device requires low voltage (5 V), low power (<3.4 mW peak power), and low energy (<10.7 mJ per 10 s pulse). The absence of oxygen emission during operation is shown through residual gas analysis, indicating that Rb is not lost through chemical reaction but rather by ion transport through the designed channel. This device is of interest for atomic physics experiments and, in particular, for portable cold-atom systems where dynamic control of alkali vapor density can enable advances in science and technology.
We demonstrate a novel way to form and deplete a vapor-cell magneto-optic trap (MOT) using a reversible, solid-state alkali-metal source via an applied polarized voltage. Using ∼100 mW of electrical power, a trapped-atom number of 5×106 has been achieved, starting from near zero and the timescales of the MOT formation and depletion of ∼1 s. This fast, reversible, and low-power alkali-atom source is desirable in both tabletop and portable cold-atom systems. The core technology of this device should translate readily to other alkali and alkaline-earth elements that could find a wide range of uses in cold-atom systems and instruments.
We investigate a solid-state reversible alkali-ion battery (AIB) capable of regulating the density of alkali atoms in a vacuum system used for the production of laser-cooled atoms. The cold-atom sample can be used with in-vacuum chronoamperometry as a diagnostic for the voltage-controlled electrochemical reaction that sources or sinks alkali atoms into the vapor. In a combined reaction-diffusion-limited regime, we show that the number of laser-cooled atoms in a magneto-optical trap can be increased both by initially loading the AIB from the vapor for longer and by using higher voltages across the AIB when atoms are subsequently sourced back into the vapor. The time constants associated with the change in atom number in response to a change in AIB voltage are in the range of 0.5--40 s. The AIB alkali reservoir is demonstrated to survive oxidization during atmospheric exposure, simplifying reservoir loading prior to vacuum implementation as a replacement for traditional resistively heated dispensers. The AIB capabilities may provide an improved atom-number stability in next-generation atomic clocks and sensors, while also facilitating fast loading and increased interrogation times.
In this paper we present a novel fabrication technique for coherent population trapping based chip-sized alkali vapor cells. There are two cavities in the cell design, one is a reaction cavity for alkali dispenser and the other one is a working cavity for alkali storage. An alkali dispenser pill is placed in the reaction cavity and subsequently reacted to obtain pure alkali material. The alkali atoms can be transferred into the working cavity in vapor form once the cell is heated up to 70 degree. Since alkali reacts with many materials and cannot be handled in air, our method provides a low cost and high reproducible way to fabricate highly miniaturized vapor cells. Silicon micromachining and glass-Si-glass three-layer anodic bonding technology is applied to introduce alkali atoms and a buffer gas into the cell and effectively seal this environment within the cell. A rubidium vapor cell is demonstrated using our design. The cell size is 5×4×1.6 mm 3 , with hermetic seal leakage <5e −9 atm cc/s. Modulated optical absorption spectrum of the cell is obtained and matched with pure rubidium atom, indicating the suitability of these cells for use in highly miniaturized atomic frequency references based on CPT excitation scheme. In addition, the entire process is fabricated at the wafer level, with subsequent dicing into individual cells.
The microfabricated alkali atomic vapor cells are essential for the chip scale quantum sensing instruments which provide a robust, simple platform for precision measurement for a quantum system. In order to solve the problems of difficult quantitative filling of alkali atoms and poor hermeticity in the fabricated process of the cells, the preparation of microfabricated alkali atomic vapor cells with good hermeticity is studied. The cells are fabricated by the microelectromechanical system (MEMS) technology. Rubidium (Rb) atomic vapor cells with nitrogen (N 2 ) as buffer gas are successfully obtained by photolysis of rubidium azide (RbN 3 ), which is confirmed by the presence of Rb vapor in the cells through absorption spectroscopy for the 5S 1/2 → 5P 3/2 and 5S 1/2 → 5P 1/2 transitions in Rb atoms at 780 nm and 795 nm. The influences of filling amount and baking temperature of RbN 3 solution on the hermeticity of the microfabricated atomic vapor cells are demonstrated. Also, the influences of filling amount of Rb atoms and temperature on the absorption spectrum intensities of Rb vapor in the cells are studied through a theoretical analysis. This research provides a reference for the design and preparation of high quality microfabricated alkali atomic vapor cells.