We present a compact, transportable system that produces Bose–Einstein condensates near the surface of an integrated atom microchip. The system occupies a volume of 0.4 m3, operates at a repetition rate as high as 0.3 Hz, and consumes an average power of 525 W. Evaporative cooling in a chip trap with trap frequencies of several kilohertz leads to nearly pure condensates containing 1.9×104 R87b atoms. Partial condensates are observed at a temperature of 1.58(8) μK, close to the theoretical transition temperature of 1.1 μK.
Atom chips are an excellent tool for studying ultracold degenerate quantum gases, due to the high degree of controllability afforded by the precise potentials generated from the current-carrying microfabricated wires on the chip surface. The geometries of the trapping potentials are inherently capable of realising extreme aspect ratios, and therefore creating model systems with effectively reduced dimensionality, particularly the theoretically-tractable one-dimensional Bose gas. In addition, the temporal tunability makes it possible to impart non-adiabatic changes on the trapping potentials, allowing experimental investigation of samples which have been brought out of equilibrium - a situation which is not fully theoretically understood. This thesis describes the implementation, development and characterisation of an experimental system for producing the first Bose-Einstein condensates of atomic rubidium 87 gas trapped on the surface of an atom chip in Nottingham. Such an apparatus is very complex and requires careful characterisation in order to run in a stable and reliable way. Details of the experimental setup are thoroughly outlined, including the vacuum system, lasers, electronics, computer control and timing, and the optical imaging system. A newly installed compact two-dimensional magneto-optical trap provides an loading rate of 5e7 atoms per second for loading a three-dimensional mirror-magneto-optical trap with 1.5e8 atoms, at a temperature of 300uK within 10s. The cloud is then sub-Doppler cooled to 50uK, and spin-polarised with 96% purity into the |F=2,mF=+2> ground state within 5ms, in preparation for loading a purely magnetic trap. A millimeter sized copper Z-shaped conductor located beneath the atom chip surface creates a Ioffe-Pritchard magnetic trap, into which the laser cooled cloud is loaded with 70% efficiency, and can be held with a vacuum-limited lifetime of 40s. Evaporative cooling then pre-cools the sample to below 20uK within 10s, to allow the subsequent loading into potentials created by the atom chip with 100% efficiency. A final evaporation stage then cools the cloud below the phase transition temperature of 800nK, resulting finally in pure BECs with
105 atoms confined using the atom chip. Key measurements of various properties of the trapped condensates are presented, which are important in order to characterise the system fully, and to compare with theoretical expectations. In particular, included are the variation of condensate fraction with temperature, the BEC expansion dynamics, and the condensate lifetime in the trap, for example. Finally, it is demonstrated how BECs can be produced on the atom chip without the use of external macroscopic coils, achieved by using novel, integrated sheet structures located beneath the chip surface - unique to this experimental system - to create the necessary bias fields.
We construct a compact experimental apparatus for producing high-repetition-rate ultra cold 87Rb atom based on an external atom chip. Initially, we produce an atomic flux from a 2D+ MOT (magneto-optical trap) in a nearly isolated 2D+ MOT chamber and improve the flux by adjusting the cooling beam detuning of the 2D+ MOT. The flux is trapped in the 3D MOT for 1.2 s and is further cooled by performing compressing the MOT for 20 ms and using polarization gradient cooling for 6.2 ms. After optical pumping into the 5S F = 2 (m F = 2) ground state, we transport atoms toward the chip surface by performing external Z coil trapping. At 1 mm below the chip surface, the external Z coil trap is completely switched to an atom chip trap by using a Z wire and a dimple wire on the chip with external bias fields. The transport and the switching take totally 520 ms. The number of atoms trapped on the atom chip is measured to be about 2 × 107. After the atoms has been compressed for 100 ms to increase trap frequencies, we perform RF evaporative cooling in the RF frequency range from 32 MHz to 6.82 MHz for 2.4 seconds. The final number of atoms in the atomic cloud after RF cooling is 1.2 × 105 atoms, and we are able to observe some Bose-Einstein condensation. The repetition rate for producing the condensation is 0.234 Hz. In this paper, we describe our experimental apparatus and processes.
We present a dual chamber atom chip apparatus for generating ultracold (87)Rb and (39)K atomic gases. The apparatus produces quasi-pure Bose-Einstein condensates of 10(4) (87)Rb atoms in an atom chip trap that features a dimple and good optical access. We have also demonstrated production of ultracold (39)K and subsequent loading into the chip trap. We describe the details of the dual chamber vacuum system, the cooling lasers, the magnetic trap, the multicoil magnetic transport system, the atom chip, and two optical dipole traps. Due in part to the use of light-induced atom desorption, the laser cooling chamber features a sufficiently good vacuum to also support optical dipole trap-based experiments. The apparatus is well suited for studies of atom-surface forces, quantum pumping and transport experiments, atom interferometry, novel chip-based traps, and studies of one-dimensional many-body systems.
In this thesis I discuss work that has been carried out on the dynamics of a Bose Einstein condensate of Rb 87 produced near an atom chip. A Bose Einstein Condensate (BEC) is a quantum state of matter where a single quantum state becomes occupied by a macroscopic number of identical Bosons. In our case this is achieved by cooling a system of trapped identical rubidium 87 atoms to its ground state. To reach temperatures of condensation we initially laser cool atoms from room temperature, before loading them into a magnetic trap. The magnetic trap is produced through a combination of uniform magnetic fields from coils outside our vacuum chamber and currents running through wires on an atom chip. The atom chip is a microfabricated device, produced by a coating a silicon chip with a thin layer of gold and etching wires into it. Together, these fields create a magnetic field minimum 120μm from the surface of the chip which can be used to confine low field seeking hyperfine states of the atom in an elongated harmonic trap. Once the atoms are confined in the magnetic trap we used force evaporative cooling out to reach the phase space densities required for Bose Einstein condensation. The BEC is used to investigate the relative dynamics between the fraction of the atoms in the condensate to those not in the condensate. Our atom chip provided a suitable environment to investigate this due to fragmentation of the magnetic potential close to the chip. Small imperfections in the wires on our atom chip mean that the trapping potential isn’t smooth. Small regions of higher trapping frequency - or fragments - are formed. Due to the small size of these fragments it is possible to find a position where a condensate can form in the fragment, and see a potential of high frequency, whereas a non-condensed atom will see a lower frequency potential. We exploit this to set the condensed fraction moving relative to the non condensed part and investigate the subsequent damping of their motion relative to each other.
The work in this thesis falls into two broad categories: creating Bose-Einstein condensates (BECs) in compact and portable systems, and manipulating neutral atoms in small systems to facilitate a continuously running neutral Rydberg atom quantum computer. The work with BECs focused on the miniaturization of ultracold matter systems. Ultracold matter has potential uses in many practical applications, such as atomic clocks, inertial sensors, and electric and magnetic field sensing. Much of the potential of atom chip based systems relies on the ability for the system to make its way out of the lab. The BEC system created occupies a volume of 0.4m^3 and operates at a repetition rate as high as 0.3Hz, creating Rubidium BECs of around 20k atoms. The system contains all of the components needed to produce and image BECs, including the UHV system, lasers, data acquisition hardware, electronics, and imaging equipment. The system can be easily reconfigured for different applications simply by changing the atom chip. As such, the hope is that it can serve as a standardized platform for a variety of portable experiments that utilize ultracold matter. The quantum computing work focuses on the ongoing work in atom manipulation for neutral Rydberg atom quantum computing. Neutral Rydberg atom quantum computing has great potential and, by harnessing the tool kit developed working with cold atoms, has the potential of scalability and continuous operation. An entirely new laser system and vacuum cell was built to work with Cesium. We have currently built a state of the art vacuum cell and developed far-detuned optical trapping and transport techniques to facilitate continuous quantum computing. Ongoing efforts include optical lattice generation and single-atom manipulation and imaging.