Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:1311.6961 · Review of Scientific Instruments

Integrated fiber-mirror ion trap for strong ion-cavity coupling

B. Brandstätter, Andrew McClung, Klemens Schüppert, Bernardo Casabone, Konstantin Friebe, Andreas Stute, Piet O. Schmidt, Christian Deutsch, Jakob Reichel, R. Blatt, Tracy E. Northup

Published Dec 1, 2013• 89 citations
arXivHTMLPDF

Abstract

We present and characterize fiber mirrors and a miniaturized ion-trap design developed to integrate a fiber-based Fabry-Perot cavity (FFPC) with a linear Paul trap for use in cavity-QED experiments with trapped ions. Our fiber-mirror fabrication process not only enables the construction of FFPCs with small mode volumes, but also allows us to minimize the influence of the dielectric fiber mirrors on the trapped-ion pseudopotential. We discuss the effect of clipping losses for long FFPCs and the effect of angular and lateral displacements on the coupling efficiencies between cavity and fiber. Optical profilometry allows us to determine the radii of curvature and ellipticities of the fiber mirrors. From finesse measurements, we infer a single-atom cooperativity of up to 12 for FFPCs longer than 200 μm in length; comparison to cavities constructed with reference substrate mirrors produced in the same coating run indicates that our FFPCs have similar scattering losses. We characterize the birefringence of our fiber mirrors, finding that careful fiber-mirror selection enables us to construct FFPCs with degenerate polarization modes. As FFPCs are novel devices, we describe procedures developed for handling, aligning, and cleaning them. We discuss experiments to anneal fiber mirrors and explore the influence of the atmosphere under which annealing occurs on coating losses, finding that annealing under vacuum increases the losses for our reference substrate mirrors. X-ray photoelectron spectroscopy measurements indicate that these losses may be attributable to oxygen depletion in the mirror coating. Special design considerations enable us to introduce a FFPC into a trapped ion setup. Our unique linear Paul trap design provides clearance for such a cavity and is miniaturized to shield trapped ions from the dielectric fiber mirrors. We numerically calculate the trap potential in the absence of fibers. In the experiment additional electrodes can be used to compensate distortions of the potential due to the fibers. Home-built fiber feedthroughs connect the FFPC to external optics, and an integrated nanopositioning system affords the possibility of retracting or realigning the cavity without breaking vacuum.

DOI
10.1063/1.4838696

Related papers

Towards an integrated ion trap - cavity system with strong coupling for multiple ions

Jack Morphew

Precise control over internal states of atomic ions in ion traps has been possible for many years enabling high precision spectroscopy of atomic transitions. Trapped ions are suitable candidates for quantum information processing due to their long storage times, low decoherence rates and high readout efficiency. Recent advances in micro-machining fibre optic mirrors and integrated fibre optic-ion trap systems for cavity QED allows one to realise strong coupling between an ion and a cavity mode by reducing the mode volume. For strong ion-cavity coupling, deterministic transfer of quantum states between ions and photons is possible. We have designed and constructed a miniaturised linear Paul trap with an integrated optical cavity, intended for coupling multiple ions to the cavity mode. The RF-electrode separation is 50μm, while the endcap separation is 350μm. The endcap electrodes are narrow tubes of inner diameter 300μm allowing optical fibers through the tubes to form the cavity. The trap depth we calculate to be 650meV for a 10V applied potential at 20MHz. The 4P1⁄2→ 3D3⁄2 transition of the atomic ion 40Ca+ with Γ = 24π × 22MHz can be coupled to an optical fibre Fabry-Perot cavity with length of 380µm, finesse of 33,000 and cavity linewidth k = 2π ×11MHz.The ion-cavity coherent coupling g = 2π × 19:5MHz of this system will put it in single-ion strong coupling regime with cooperativity, C=1.5.

•Sep 1, 2016•0 citations

Design and fabrication of metal-shielded fiber-cavity mirrors for ion-trap systems

CHEN Wei-Bin, Ding Fang, Cheng-Hao Zhang +4 more

Abstract Trapped ions in micro-cavities constitute a key platform for advancing quantum information processing and quantum networking. By providing an efficient light–matter interface within a compact architecture, they serve as highly efficient quantum nodes with strong potential for a scalable quantum network. However, in such systems, ion trapping stability is often compromised by surface charging effects, and nearby dielectric materials are known to cause a dramatic increase in the ion heating rate by several orders of magnitude. These challenges significantly hinder the practical implementation of ion trap systems integrated with micro-cavities. To overcome these limitations, we present the design and fabrication of metal-shielded fiber-cavity mirrors, enabling the stable realization of ion trap systems integrated with fiber cavities. Using this method, we constructed a needle ion trap integrated with a fiber Fabry–Pérot cavity and successfully achieved stable trapping of a single ion within the cavity. The measured ion heating rate was reduced by more than an order of magnitude compared with unshielded configurations. This work establishes a key technique toward fully integrated ion–photon interfaces for scalable quantum networks.

Quantum Science and Technology•Jan 13, 2026•1 citation

Integrating a fiber cavity into a wheel trap for strong ion–cavity coupling

Markus Teller, Viktor Messerer, Klemens Schüppert +6 more

We present an ion trap with an integrated fiber cavity, designed for strong coupling at the level of single ions and photons. The cavity is aligned to the axis of a miniature linear Paul trap, enabling simultaneous coupling of multiple ions to the cavity field. We simulate how charges on the fiber mirrors affect the trap potential, and we test these predictions with an ion trapped in the cavity. Furthermore, we measure micromotion and heating rates in the setup.

AVS Quantum Science•Jan 25, 2023•19 citations

Design and characterization of an integrated surface ion trap and micromirror optical cavity

Andre J. Van Rynbach, George Schwartz, Robert Spivey +3 more

We have fabricated and characterized laser-ablated micromirrors on fused silica substrates for constructing stable Fabry–Perot optical cavities. We highlight several design features which allow these cavities to have lengths in the 250–300 μm range and be integrated directly with surface ion traps. We present a method to calculate the optical mode shape and losses of these micromirror cavities as functions of cavity length and mirror shape, and confirm that our simulation model is in good agreement with experimental measurements of the intracavity optical mode at a test wavelength of 780 nm. We have designed and tested a mechanical setup for dampening vibrations and stabilizing the cavity length, and explore applications for these cavities as efficient single-photon sources when combined with trapped Yb171+ ions.

Applied Optics•Aug 3, 2017•1 citation

High finesse optical fiber cavities: optimal alignment and robust stabilization (Conference Presentation)

Lothar Ratschbacher, Jose Gallego, Sutapa Ghosh +4 more

Fiber Fabry-Perot cavities, formed by micro-machined mirrors on the end-facets of optical fibers, are used in an increasing number of technical and scientific applications. Some of the most promising areas of application of these optical micro-resonators with high finesse and small mode volume are in the field of quantum communication and information. The resonator-enhanced light-matter interaction, for instance, provide basis for the realization of efficient optical interfaces between stationary matter-based quantum nodes and flying single-photon qubits. To date fiber Fabry-Perot cavities have been successfully applied in experiments interfacing single photons with a wide range of quantum systems, including cold atoms, ions and solid state emitters as well as quantum optomechanical experiments. Here we address some important practical questions that arise during the experimental implementation of high finesse fiber Fabry-Perot cavities: How can optimal fiber cavity alignment be achieved and how can the efficiency of coupling light from the optical fibers to the cavity mode and vice versa be characterized? How should optical fiber cavities be constructed and stabilized to fulfill their potential for miniaturization and integration into robust scientific and technological devices that can operate outside of dedicated laboratory environments in the future? The first two questions we answer with an analytic mode matching calculation that relates the alignment dependent fiber-to-cavity mode-matching efficiency to the easily measurable dip in the reflected light power at the cavity resonance. Our general analysis provides a simple recipe for the optimal alignment of fiber Fabry-Perot cavities and moreover for the first time explains the asymmetry in their reflective line shapes. The latter question we explore by investigating a novel, intrinsically rigid fiber cavity design that makes use of the high passive stability of a monolithic cavity spacer and employs thermal self-locking and external temperature tuning. The performance of this novel approach is compared to a more traditional, piezomechanically-actuated resonator that is feedback stabilized to a reference laser based on the Pound-Drever-Hall locking technique. Finally, with the application of single photon interfacing in mind we discuss the issue of fiber-generated background photons in Fiber Fabry-Perot cavities. We believe that, due to their simplicity, compactness and robustness, rigid fiber cavities could be a promising solution for miniaturized, integratable and scalable cavity quantum electrodynamic devices and further applications of FFPC with similar requirements.

•Aug 3, 2016•0 citations

Cavity-QED implementations for distributive quantum computation

Hamzah Shokeir

The coupling of a single ion to an optical cavity is a promising route towards scalable quantum technologies. This study presents the design, initial construction and simulations of two different ion traps for quantum computation with novel capabilities. The first system is an end cap system that utilises Fabry Perot cavities formed by the facets of fibres. The small mode volumes (cavity length ~ 300 µm) of the fibre cavities are ideal to achieve high cooperativity and coupling strength. This trap features the novel ability to mechanically adjust the position of the ion by perturbing/distorting the trapping potential with grounded side electrodes. A capability crucial to maximising the ion-cavity coupling. The design incorporates a number of improvements over the previous iteration by Takahashi et al. such as increased optical access, increased mode matching and improved mechanical stability of the cavity. To verify and test the design modifications; Pound-Drever-Hall cavity locking was set up. The test set up failed to lock to an error signal due to a mechanically unstable translation stage. The other design presented is a linear micro trap intended to trap strings of ions and does not use fibre based cavities. This design features multiple different regions reserved for storage, computation and communication and aims to implement a shuttling scheme that will allow the selective loading of single ions from a reservoir of ions into the desired regions. The fabrication process would utilise methods in microfabrication. Simulations of the trapping dynamics were used to optimise the electrode geometries and splitting protocol.

•Dec 9, 2020•0 citations
We present and characterize fiber mirrors and a miniaturized ion-trap design developed to integrate a fiber-based Fabry-Perot cavity (FFPC) with a linear Paul trap for use in cavity-QED experiments with trapped ions. Our fiber-mirror fabrication process not only enables the construction of FFPCs with small mode volumes, but also allows us to minimize the influence of the dielectric fiber mirrors on the trapped-ion pseudopotential. We discuss the effect of clipping losses for long FFPCs and the effect of angular and lateral displacements on the coupling efficiencies between cavity and fiber. Optical profilometry allows us to determine the radii of curvature and ellipticities of the fiber mirrors. From finesse measurements, we infer a single-atom cooperativity of up to 12 for FFPCs longer than 200 μm in length; comparison to cavities constructed with reference substrate mirrors produced in the same coating run indicates that our FFPCs have similar scattering losses. We characterize the birefringence of our fiber mirrors, finding that careful fiber-mirror selection enables us to construct FFPCs with degenerate polarization modes. As FFPCs are novel devices, we describe procedures developed for handling, aligning, and cleaning them. We discuss experiments to anneal fiber mirrors and explore the influence of the atmosphere under which annealing occurs on coating losses, finding that annealing under vacuum increases the losses for our reference substrate mirrors. X-ray photoelectron spectroscopy measurements indicate that these losses may be attributable to oxygen depletion in the mirror coating. Special design considerations enable us to introduce a FFPC into a trapped ion setup. Our unique linear Paul trap design provides clearance for such a cavity and is miniaturized to shield trapped ions from the dielectric fiber mirrors. We numerically calculate the trap potential in the absence of fibers. In the experiment additional electrodes can be used to compensate distortions of the potential due to the fibers. Home-built fiber feedthroughs connect the FFPC to external optics, and an integrated nanopositioning system affords the possibility of retracting or realigning the cavity without breaking vacuum.
Precise control over internal states of atomic ions in ion traps has been possible for many years enabling high precision spectroscopy of atomic transitions. Trapped ions are suitable candidates for quantum information processing due to their long storage times, low decoherence rates and high readout efficiency. Recent advances in micro-machining fibre optic mirrors and integrated fibre optic-ion trap systems for cavity QED allows one to realise strong coupling between an ion and a cavity mode by reducing the mode volume. For strong ion-cavity coupling, deterministic transfer of quantum states between ions and photons is possible. We have designed and constructed a miniaturised linear Paul trap with an integrated optical cavity, intended for coupling multiple ions to the cavity mode. The RF-electrode separation is 50μm, while the endcap separation is 350μm. The endcap electrodes are narrow tubes of inner diameter 300μm allowing optical fibers through the tubes to form the cavity. The trap depth we calculate to be 650meV for a 10V applied potential at 20MHz. The 4P1⁄2→ 3D3⁄2 transition of the atomic ion 40Ca+ with Γ = 24π × 22MHz can be coupled to an optical fibre Fabry-Perot cavity with length of 380µm, finesse of 33,000 and cavity linewidth k = 2π ×11MHz.The ion-cavity coherent coupling g = 2π × 19:5MHz of this system will put it in single-ion strong coupling regime with cooperativity, C=1.5.
Abstract Trapped ions in micro-cavities constitute a key platform for advancing quantum information processing and quantum networking. By providing an efficient light–matter interface within a compact architecture, they serve as highly efficient quantum nodes with strong potential for a scalable quantum network. However, in such systems, ion trapping stability is often compromised by surface charging effects, and nearby dielectric materials are known to cause a dramatic increase in the ion heating rate by several orders of magnitude. These challenges significantly hinder the practical implementation of ion trap systems integrated with micro-cavities. To overcome these limitations, we present the design and fabrication of metal-shielded fiber-cavity mirrors, enabling the stable realization of ion trap systems integrated with fiber cavities. Using this method, we constructed a needle ion trap integrated with a fiber Fabry–Pérot cavity and successfully achieved stable trapping of a single ion within the cavity. The measured ion heating rate was reduced by more than an order of magnitude compared with unshielded configurations. This work establishes a key technique toward fully integrated ion–photon interfaces for scalable quantum networks.
We have fabricated and characterized laser-ablated micromirrors on fused silica substrates for constructing stable Fabry–Perot optical cavities. We highlight several design features which allow these cavities to have lengths in the 250–300 μm range and be integrated directly with surface ion traps. We present a method to calculate the optical mode shape and losses of these micromirror cavities as functions of cavity length and mirror shape, and confirm that our simulation model is in good agreement with experimental measurements of the intracavity optical mode at a test wavelength of 780 nm. We have designed and tested a mechanical setup for dampening vibrations and stabilizing the cavity length, and explore applications for these cavities as efficient single-photon sources when combined with trapped Yb171+ ions.
Fiber Fabry-Perot cavities, formed by micro-machined mirrors on the end-facets of optical fibers, are used in an increasing number of technical and scientific applications. Some of the most promising areas of application of these optical micro-resonators with high finesse and small mode volume are in the field of quantum communication and information. The resonator-enhanced light-matter interaction, for instance, provide basis for the realization of efficient optical interfaces between stationary matter-based quantum nodes and flying single-photon qubits. To date fiber Fabry-Perot cavities have been successfully applied in experiments interfacing single photons with a wide range of quantum systems, including cold atoms, ions and solid state emitters as well as quantum optomechanical experiments. Here we address some important practical questions that arise during the experimental implementation of high finesse fiber Fabry-Perot cavities: How can optimal fiber cavity alignment be achieved and how can the efficiency of coupling light from the optical fibers to the cavity mode and vice versa be characterized? How should optical fiber cavities be constructed and stabilized to fulfill their potential for miniaturization and integration into robust scientific and technological devices that can operate outside of dedicated laboratory environments in the future? The first two questions we answer with an analytic mode matching calculation that relates the alignment dependent fiber-to-cavity mode-matching efficiency to the easily measurable dip in the reflected light power at the cavity resonance. Our general analysis provides a simple recipe for the optimal alignment of fiber Fabry-Perot cavities and moreover for the first time explains the asymmetry in their reflective line shapes. The latter question we explore by investigating a novel, intrinsically rigid fiber cavity design that makes use of the high passive stability of a monolithic cavity spacer and employs thermal self-locking and external temperature tuning. The performance of this novel approach is compared to a more traditional, piezomechanically-actuated resonator that is feedback stabilized to a reference laser based on the Pound-Drever-Hall locking technique. Finally, with the application of single photon interfacing in mind we discuss the issue of fiber-generated background photons in Fiber Fabry-Perot cavities. We believe that, due to their simplicity, compactness and robustness, rigid fiber cavities could be a promising solution for miniaturized, integratable and scalable cavity quantum electrodynamic devices and further applications of FFPC with similar requirements.
The coupling of a single ion to an optical cavity is a promising route towards scalable quantum technologies. This study presents the design, initial construction and simulations of two different ion traps for quantum computation with novel capabilities. The first system is an end cap system that utilises Fabry Perot cavities formed by the facets of fibres. The small mode volumes (cavity length ~ 300 µm) of the fibre cavities are ideal to achieve high cooperativity and coupling strength. This trap features the novel ability to mechanically adjust the position of the ion by perturbing/distorting the trapping potential with grounded side electrodes. A capability crucial to maximising the ion-cavity coupling. The design incorporates a number of improvements over the previous iteration by Takahashi et al. such as increased optical access, increased mode matching and improved mechanical stability of the cavity. To verify and test the design modifications; Pound-Drever-Hall cavity locking was set up. The test set up failed to lock to an error signal due to a mechanically unstable translation stage. The other design presented is a linear micro trap intended to trap strings of ions and does not use fibre based cavities. This design features multiple different regions reserved for storage, computation and communication and aims to implement a shuttling scheme that will allow the selective loading of single ions from a reservoir of ions into the desired regions. The fabrication process would utilise methods in microfabrication. Simulations of the trapping dynamics were used to optimise the electrode geometries and splitting protocol.