A quantum computer will use the properties of quantum physics to solve certain computational problems much faster than otherwise possible. One promising potential implementation is to use superconducting quantum bits in the circuit quantum electrodynamics (cQED) architecture. There, the low energy states of a nonlinear electronic oscillator are isolated and addressed as a qubit. These qubits are capacitively coupled to the modes of a microwave-frequency transmission line resonator which serves as a quantum communication bus. Microwave electrical pulses are applied to the resonator to manipulate or measure the qubit state. State control is calibrated using diagnostic sequences that expose systematic errors. Hybridization of the resonator with the qubit gives it a nonlinear response when driven strongly, useful for amplifying the measurement signal to enhance accuracy. Qubits coupled to the same bus may coherently interact with one another via the exchange of virtual photons. A two-qubit conditional phase gate mediated by this interaction can deterministically entangle its targets, and is used to generate two-qubit Bell states and three-qubit GHZ states. These three-qubit states are of particular interest because they redundantly encode quantum information. They are the basis of the quantum repetition code prototypical of more sophisticated schemes required for quantum computation. Using a three-qubit Toffoli gate, this code is demonstrated to autonomously correct either bit- or phase-flip errors. Despite observing the expected behavior, the overall fidelity is low because of decoherence. A superior implementation of cQED replaces the transmission-line resonator with a three-dimensional box mode, increasing lifetimes by an order of magnitude. In-situ qubit frequency control is enabled with control lines, which are used to fully characterize and control the system Hamiltonian.
A quantum computer will use the properties of quantum physics to solve certain computational problems much faster than otherwise possible. One promising potential implementation is to use superconducting quantum bits in the circuit quantum electrodynamics (cQED) architecture. There, the low energy states of a nonlinear electronic oscillator are isolated and addressed as a qubit. These qubits are capacitively coupled to the modes of a microwave-frequency transmission line resonator which serves as a quantum communication bus. Microwave electrical pulses are applied to the resonator to manipulate or measure the qubit state. State control is calibrated using diagnostic sequences that expose systematic errors. Hybridization of the resonator with the qubit gives it a nonlinear response when driven strongly, useful for amplifying the measurement signal to enhance accuracy. Qubits coupled to the same bus may coherently interact with one another via the exchange of virtual photons. A two-qubit conditional phase gate mediated by this interaction can deterministically entangle its targets, and is used to generate two-qubit Bell states and three-qubit GHZ states. These three-qubit states are of particular interest because they redundantly encode quantum information. They are the basis of the quantum repetition code prototypical of more sophisticated schemes required for quantum computation. Using a three-qubit Toffoli gate, this code is demonstrated to autonomously correct either bit- or phase-flip errors. Despite observing the expected behavior, the overall fidelity is low because of decoherence. A superior implementation of cQED replaces the transmission-line resonator with a three-dimensional box mode, increasing lifetimes by an order of magnitude. In-situ qubit frequency control is enabled with control lines, which are used to fully characterize and control the system Hamiltonian.
In a quantum computer, the information carriers, which are bits in ordinary computers, are implemented as devices that exhibit coherent superpositions of physical states and entanglement. Such components, known as quantum bits or qubits, can be realized with various different types of two-state quantum systems. Quantum computers will be built for computational speed, with hoped for applications especially in cryptography and in other tasks where classical computers remain inefficient. Circuit quantum electrodynamics (cQED) is a quantum-computer architecture which employs superconducting electronic components and microwave photon fields as building blocks. Compared to cavity quantum electrodynamics (CQED), where atoms are trapped in physical cavities, cQED is more attractive in that its qubits are tunable and conveniently integrable with the electronics already in use. This architecture has shown some of the most promising qubit designs, despite their coherence times reaching tens of microseconds, are still below the state of the art with spin qubits, which reach milliseconds. Coherence times are historically the most relevant parameters describing the fitness of a qubit, although these days not necessarily the limiting factor. This thesis presents a comprehensive set of theoretical and experimental methods for measuring the characteristic parameters of superconducting qubits. We especially study transmission-line-shunted plasma oscillation qubits, or transmons, and presents experimental results for a single sample. Transmon capacitively couples a superconducting quantum interference device (SQUID) with a coplanar waveguide (CPW) resonator, often with added frequency tunability utilizing an external magnet. The number of superconducting charge carriers tunnelled through a junction in the SQUID are used as qubit degrees of freedom. Readout of the qubit state is carried out by measuring transmission through the CPW. A cryogenic setup is employed with measurement and driving pulses delivered from microwave sources. Steady-state spectroscopy is employed to determine the resonance frequencies of the qubit and the resonator, qubit-resonator coupling constants, and the energy parameters of the qubit. Pulse-modulated measurements are employed to determine the coherence times of the qubit. The related analysis- and simulation programs and scripts are collected togithub.com/patomaki.
Circuit quantum electrodynamics (cQED), exemplified by a coupled system of a superconducting qubit and a microwave cavity, is a powerful framework for the quantum control and measurement of macroscopic quantum states in solid-state circuits. Quantum circuits based on superconducting qubits have emerged as one of the leading platforms in the pursuit of fault-tolerant quantum computing. Despite significant progress in extending qubit lifetimes, refining experimental protocols, and scaling up quantum processors, errors arising from the control and measurement of superconducting qubits continue to hinder the realization of a universal quantum computer. To investigate the error mechanisms for state-of-the-art qubits, we realize long-lived superconducting transmon qubits that exhibit fluctuating lifetimes, with an average of 0.2 ms and a maximum exceeding 0.4 ms. We then investigate their dominant error mechanism. By introducing novel time-resolved error measurements that are synchronized with the operation of the pulse tube cooler in a dilution refrigerator, we find that mechanical vibrations from the pulse tube induce nonequilibrium dynamics in highly coherent qubits, leading to their correlated bit-flip errors. Our findings not only deepen our understanding of qubit error mechanisms but also provide valuable insights into potential error-mitigation strategies for achieving fault tolerance by decoupling superconducting qubits from their mechanical environments. We also present a novel scheme for operating a cQED system in a regime where the cavity is largely displaced. We find that a qubit drive at the bare cavity frequency can effectively displace the cavity field while minimizing the cavity-drive-induced dephasing and the ac Stark shift. Furthermore, we demonstrate that standard cQED protocols, such as qubit control, readout, and cavity single-photon generation, remain compatible with largely displaced cavity fields, even beyond the critical photon number. These findings open new pathways for exploring cQED dynamics in large-photon-number regimes, including the study of nonlinear phenomena in microwave cavities, the saturation of two-level system baths for extending the coherence of microwave quantum states, and the acceleration of the dispersive readout. Finally, mechanical resonators have emerged as integral components in quantum computing for storing and transducing quantum information. Low-frequency mechanical resonators, with extremely low energy dissipation rates, are particularly interesting for extending the lifetimes of stored quantum information. However, integrating low-frequency mechanical resonators with qubits is challenging because their small energy gaps make coherent energy exchange and ground-state preparation difficult. In this thesis, we report the first steps towards the characterization of a hybrid quantum device, consisting of a Transmon qubit and a circuit optomechanical system, both coupled to a 3D microwave cavity.
The discovery of quantum mechanics in the 20th century forms the basis of many of the technologies that define our lives today. The ability to engineer and manipulate individual quantum systems -- even create artificial atoms -- promises a similar revolutionary leap in technology. A quantum technology of particular interest is quantum computing, which has the potential to solve problems that are intractable for classical computers, opening up new domains of computation. Meanwhile, an attractive approach to creating engineered quantum systems is circuit quantum electrodynamics (cQED). Where research initially focused on understanding the physics of cQED devices, focus has shifted to building systems capable of performing useful computations. However, this remains extremely challenging, in part due to the inherently fragile nature of the individual quantum bits, but also due to difficulties in controlling and scaling up these systems. This thesis focuses on the control aspects of building an extensible full-stack quantum computer based on superconducting transmon qubits. We define the demonstration of quantum fault-tolerance as our target application to give focus to our efforts. The QuSurf architecture for a full-stack quantum computer presented in this thesis is designed with this application in mind. We provide a detailed study of the error sources present in this system and give an overview of the relevant characterization techniques. In the second part of this thesis, we address several key challenges in the control of a quantum computer. To realize high-fidelity coherence limited gates, we present a novel tuneup protocol that achieves a tenfold speedup over the state-of-the-art. This is realized by eliminating the need for qubit initialization. We demonstrate this protocol by calibrating single-qubit gates to a coherence limited Clifford fidelity of 99.9% in one minute. Performing repeated parity checks, as is required for quantum error correction, requires reusing qubits quickly after they have been measured. By introducing a numerically optimized depletion pulse we are able to speeds up the depletion of measurement photons in a readout resonator without having to rely on specific symmetry conditions. Using this technique speed up photon depletion by more than six inverse resonator linewidths, reducing the error rate in an emulated ancilla parity check by a factor 75. Flux-pulsing based two-qubit gates are the fastest two-qubit gates. However, they are also very technically demanding. The key challenge in performing these gates is addressing the distortions that control signals experience as they traverse various electrical components. We have developed Cryoscope (short for cryogenic oscilloscope) to characterize and correct these distortions. Cryoscope is an in-situ technique that uses the qubit to sample control pulses of arbitrary shape. Even when correcting distortions to within sim0.1 two-qubit gates are history-dependent due to the long timescale upon which some of these distortions act. We have invented Net-Zero, a new type of flux-pulsing based two-qubit gate, to address this problem. It makes use of a symmetry condition of the transmon to have net-zero integral, making the gate resilient to long-timescale distortions. The gate suppresses leakage out of the computational subspace to 0.1% by making use of leakage interference and has a built-in echo effect that enhances the coherence of the gate, achieving a two-qubit gate fidelity of 99.1%. Custom software is required to perform the physics experiments needed to build and operate a quantum computer. PycQED is an open-source software framework we have developed for this purpose. We discuss the design choices and concepts of PycQED before turning our focus to characterization and calibration. Here we introduced dependency graphs as a useful abstraction and system emulation as an essential development tool for automating the characterization and calibration process. We conclude the thesis by reflecting on the limitations of our architecture and providing an outlook on the grand challenges of building a useful kilo-qubit sized quantum computer. We define these challenges as The Application Problem, The Fabrication Problem, and The Calibration Problem.
Quantum computing holds the promise of solving problems that are intractable for classical computers, with applications ranging from optimization and materials simulation to cryptography. It achieves this by leveraging the exponentially scaling dimensionality of the space encoding quantum information and by executing algorithms on quantum registers in superposition states – a feature often referred to as quantum parallelism. However, while encoding information in computational units capable of exploring a continuous set of quantum states enables exponential scaling of computational power with system size, quantum systems are also more susceptible to errors than their classical counterparts. These errors take the form of both control errors, where miscalibration of the control pulses causes coherent errors on the qubit states, as well as incoherent errors due to energy relaxation and dephasing. Scaling quantum systems to run useful algorithms involving hundreds or thousands of logical qubits will require quantum error correction. In this approach, quantum information is redundantly encoded across an entangled state of many physical qubits. This has enabled experimental demonstrations across various platforms – including ion traps, superconducting circuits, and neutral atoms – showing that encoded quantum states can be preserved beyond the coherence times of the constituting physical qubits. However, quantum state preservation is only one component needed for scalable quantum computing. To execute algorithms, it is also necessary to implement quantum gates on and between encoded qubits, in a way that maintains fault tolerance by preserving the ability to correct errors as they occur during the computation. In the first part of this thesis, we demonstrate the implementation of an error-corrected quantum operation that entangles two logical qubits. This is achieved by performing lattice surgery on a distance-three surface code qubit, resulting in a logical Bell state encoded in distance-three repetition codes, which enable the correction of single bit-flip errors. We further introduce techniques to benchmark and characterize the performance of logical operations, including applying the protocol to arbitrary logical input states and performing logical quantum process tomography. Together, these results constitute one of the first realizations of error-corrected lattice surgery in superconducting circuits. While quantum error correction can correct errors provided they occur with sufficiently low frequency, it may fail when many qubits experience errors simultaneously. In the second part of this thesis, we therefore shift focus to a specific error mechanism known to cause correlated errors in superconducting circuits – quasiparticle-induced decoherence. In this case, various forms of energy deposition on the quantum device can break Cooper pairs into quasiparticles, which may subsequently diffuse to the tunnel junction and interact with the qubit state, thereby causing decoherence. In this thesis, we investigate the impact of quasiparticle tunneling on qubit performance, with a focus on infrared-induced quasiparticles. We compare the sensitivity of niobium-based qubits to those made from tantalum – a material that has gained interest in recent years following demonstrations of qubits with improved coherence times based on this material. Using a thermal radiator source, we show that the performance of tantalum qubits may be limited by infrared-induced quasiparticles in typical superconducting circuit experimental setups. By employing both ambient and in-line infrared filters, we investigate the effectiveness of different filtering strategies and develop best practices for engineering cryogenic environments for superconducting quantum processors. The results presented in this thesis contribute to the advancement of quantum computing based on superconducting circuits by implementing and characterizing quantum error-corrected operations, and by investigating quasiparticles as a source of decoherence, along with strategies to improve infrared filtering and signal conditioning in cryogenic environments for future fault-tolerant quantum computing.
Quantum computing is a novel paradigm for information processing that promises computational speedup for certain computational tasks while not being driven by Moore's law. Superconducting circuits based on Josephson junctions are one of the leading approaches for implementing the quantum bits, or qubits, in a quantum processor. Most superconducting qubit architectures involve circuit quantum electrodynamics, where the qubits are analogous to artificial atoms that are coupled to superconducting linear resonant cavities. This scheme allows for the readout of individual qubits, the manipulation of single-qubit states, and the generation of entanglement between qubits. The performance of current state-of-the-art systems is limited by decoherence of the qubits and associated gate errors. Nonetheless, experiments have been performed that already demonstrate a significant computational speedup compared to classical processing. Future implementations of fault-tolerant quantum computers will require the development of quantum error correction. Initial tests of elements of error correction in superconducting qubit arrays are underway.
Quantum computing promises exponential advantages for simulating quantum systems and solving certain computational problems beyond the reach of classical computers, but the fragility of qubits and the resulting errors present a major challenge for scalable implementations. One promising approach is to engineer qubits whose physical noise processes are intrinsically biased, enabling more efficient quantum error correction. This dissertation investigates quantum computing with superconducting Kerr-cat qubits, a bosonic qubit architecture in which qubit states are encoded in coherent states of a nonlinear oscillator stabilized by a two-photon drive. This stabilization creates an effective double-well pseudo-potential that strongly suppresses bit-flip errors while enabling universal quantum control, leading to a noise-biased qubit. A superconducting device architecture based on SNAIL nonlinear oscillators is developed to realize Kerr-cat qubits with tunable parameters and high coherence, integrating readout resonators, dedicated filters, and microwave control lines for measurement and manipulation. Universal single-qubit gates are implemented using engineered single-photon and two-photon drives to deform the pseudo-potential, and a cat-quadrature readout method is employed to achieve high-fidelity quantum nondemolition measurement. The performance of the qubits is systematically characterized through lifetime measurements and benchmarking protocols, including quantum process tomography, gate set tomography, and dihedral randomized benchmarking, revealing a strongly biased noise structure with high performance. These results establish an experimental framework for the design, control, and characterization of Kerr-cat qubits and demonstrate their potential as hardware-efficient building blocks for scalable fault-tolerant quantum computing.