Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:1310.3966 · New Journal of Physics

Investigation of nonlinear effects in Josephson parametric oscillators used in circuit quantum electrodynamics

Philip Krantz, Yarema Reshitnyk, Waltraut Wustmann, Jonas Bylander, Simon Gustavsson, William D. Oliver, T. Duty, Vitaly Shumeiko, Per Delsing

Published Oct 7, 2013• 52 citations
arXivHTMLPDF

Abstract

We experimentally study the behavior of a parametrically pumped nonlinear oscillator, which is based on a superconducting λ /4 resonator, and is terminated by a flux-tunable superconducting quantum interference device. We extract parameters for two devices. In particular, we study the effect of the nonlinearities in the system and compare to theory. The Duffing nonlinearity, α , is determined from the probe-power dependent frequency shift of the oscillator, and the nonlinearity, β , related to the parametric flux pumping, is determined from the pump amplitude for the onset of parametric oscillations. Both nonlinearities depend on the parameters of the device and can be tuned in situ by the applied dc flux. We also suggest how to cancel the effect of β by adding a small dc flux and a pump tone at twice the pump frequency.

DOI
10.1088/1367-2630/15/10/105002

Related papers

Parametrically pumped superconducting circuits

Philip Krantz

In this licentiate thesis, I present the design, fabrication, and characterization of superconducting parametric resonators, for use in quantum information processing. These devices are quarter-wavelength coplanar waveguide resonators (~5 GHz), terminated at one end by a non-linear inductance provided by a SQUID (superconducting quantum interference device). The SQUID acts as a flux-controlled boundary condition, which effectively changes the electrical length of the resonator. This enables the modulation of the resonant frequency by coupling microwave magnetic flux into the SQUID, using on-chip transmission lines. The modulation occurs on a timescale much faster than the photon loss out of the resonator. The non-linearity provides several different regimes for operating this device. I focused on the parametric regime, in which the non-linear element was being modulated (pumped) at or near twice the resonant frequency. This pumping can lead to amplification and frequency conversion of an incoming signal. It can also give rise to instabilities and self-oscillations "parametric oscillations" - that is, the generation of an intense electric field in the resonator (the creation of photons). Parametric oscillations set in when the pumping strength exceeds a threshold value, and also depends on the pump-frequency detuning from twice the resonance and on the static flux through the SQUID. I characterized the devices over a wide parameter range by doing homodyne detection of the reflected signal or of the emitted field oscillations. In particular, I investigated the damping and two leading nonlinearities, dominating in different operating regimes, which influence the dynamics of the parametric resonator. First, I extracted the Duffing nonlinearity by studying the line width of the resonator as a function of the input signal (without pumping the SQUID). Second, with high pump amplitude, I extracted the pump-induced nonlinearity by determining the threshold parameters (pump amplitude and detuning) for the onset of parametric oscillations; this nonlinearity leads to the generation of higher-order pump terms that complicate the system dynamics, but can be mitigated now that they have been understood. My results validate a recent theoretical model for the classical, non-linear dynamics of parametric resonance, and helps determine workable design parameters. Finally, I helped develop a linearized model $-$ the "pumpistor" - describing this device in terms of a flux-controlled impedance. This will be useful when designing more complex circuits. One goal of this work is to demonstrate single-shot measurements on superconducting qubits (quantum bits of information). We will use the parametric resonator as a threshold discriminator, associating the qubit's two energy eigenstates with the parametric oscillations either turning on or not. This would be a very useful device in the quantum engineer's toolbox when designing systems for quantum information processing and communication.

•Jan 1, 2013•1 citation

Nondegenerate parametric oscillations in a tunable superconducting resonator

Andreas Bengtsson, Philip Krantz, Michaël Simoen +5 more

We investigate nondegenerate parametric oscillations in a superconducting microwave multimode resonator that is terminated by a superconducting quantum interference device (SQUID). The parametric effect is achieved by modulating magnetic flux through the SQUID at a frequency close to the sum of two resonator-mode frequencies. For modulation amplitudes exceeding an instability threshold, self-sustained oscillations are observed in both modes. The amplitudes of these oscillations show good quantitative agreement with a theoretical model. The oscillation phases are found to be correlated and exhibit strong fluctuations which broaden the oscillation spectral linewidths. These linewidths are significantly reduced by applying a weak on-resonant tone, which also suppresses the phase fluctuations. When the weak tone is detuned, we observe synchronization of the oscillation frequency with the frequency of the input. For the detuned input, we also observe an emergence of three idlers in the output. This observation is in agreement with theory indicating four-mode amplification and squeezing of a coherent input.

arXiv:1801.04566•Physical review. B./Physical review. B•Apr 4, 2018•18 citations

In situ tunable nonlinearity and competing signal paths in coupled superconducting resonators

Michael Fischer, Qiming Chen, Christian Besson +10 more

We have fabricated and studied a system of two tunable and coupled nonlinear superconducting resonators. The nonlinearity is introduced by galvanically coupled dc superconducting quantum interference devices. We simulate the system response by means of a circuit model, which includes an additional signal path introduced by the electromagnetic environment. Furthermore, we present two methods allowing us to experimentally determine the nonlinearity. First, we fit the measured frequency and flux dependence of the transmission data to simulations based on the equivalent circuit model. Second, we fit the power dependence of the transmission data to a model that is predicted by the nonlinear equation of motion describing the system. Our results show that we are able to tune the nonlinearity of the resonators by almost two orders of magnitude via an external coil and two on-chip antennas. The studied system represents a basic building block for larger systems, allowing for quantum simulations of bosonic many-body systems with a larger number of lattice sites.

arXiv:2009.13492•Physical review. B./Physical review. B•Mar 24, 2021•6 citations

Flux-driven Josephson parametric amplifier

Tsuyoshi Yamamoto, K. Inomata, 道生 渡部 +5 more

We have developed a Josephson parametric amplifier comprising a superconducting coplanar-waveguide resonator terminated by a dc superconducting quantum interference device (SQUID). An external field (the pump, ∼20 GHz) modulates the flux threading of the dc SQUID and, therefore, the resonant frequency of the cavity field (the signal, ∼10 GHz), which leads to the parametric signal amplification. We operated the amplifier at different band centers and observed amplification (17 dB at maximum) and deamplification depending on the relative phase between the pump and the signal. The noise temperature is estimated to be less than 0.87 K.

Applied Physics Letters•Jul 28, 2008•469 citations

Parametric Microwave Amplification using a Tunable Superconducting Resonator

C. W. Sandbo Chang

In this Master thesis, I present a theoretical description and experimental measurements of a tunable microwave resonator operated as a parametric amplifier. Superconducting parametric amplifiers have attracted great interest in recent years as it has been demonstrated that they can operate with a noise performance at the standard quantum limit. \nParametric amplification is achieved in the devices by modulating the electrical length of the resonator at twice the resonance frequency. The device measured in this thesis consists of a quarter-wavelength microwave resonator fabricated in a thin-film aluminum coplanar waveguide geometry. With a termination to ground through a Superconducting Quantum Interference Device (SQUID), the boundary condition of the resonator becomes sensitive to an applied magnetic field. This enables the tuning of the resonance frequencies, using a DC magnetic field, over a wide frequency range of 670MHz. Similarly, an AC magnetic field then allows for the modulation of the resonator electrical length at microwave frequencies. \nWe characterized the device by first measuring the DC tuning curves of the 2nd and 3rd harmonics of the resonator, around 4 GHz and 6 GHz respectively. We then studied parametric amplification in the device when the electrical length was modulated at approximately twice the resonance frequency of one of the modes. We scanned the pump frequency and pump power over a wide range to study the region in parameters which gives parametric gain. We performed an in-depth parameter sweep over this region, identifying pump parameters that provided maximum gain and maximum system noise improvements compared the following HEMT amplifier. \nWe find that the use of the parametric amplifier can improve the system noise temperature by more than 10 dB compared to a start-of-the-art commercial HEMT amplifier. This implies a performance near the standard quantum limit.

•Sep 2, 2015•0 citations

Spectroscopic observation of the crossover from a classical Duffing oscillator to a Kerr parametric oscillator

T. Yamaji, S. Kagami, Aiko Yamaguchi +6 more

We study microwave response of a Josephson parametric oscillator consisting of a superconducting transmission-line resonator with an embedded DC-superconducting quantum interference device (-SQUID). The DC-SQUID allows to control the magnitude of a Kerr nonlinearity over the ranges where it is smaller or larger than the photon loss rate. Spectroscopy measurements reveal the change in the microwave response from a classical Duffing oscillator to a Kerr parametric oscillator in a single device. In the single-photon Kerr regime, we observe parametric oscillations with a well-defined phase of either 0 or $\ensuremath{\pi}$, whose probability can be controlled by an externally injected signal.

arXiv:2010.02621•Physical Review A•Feb 23, 2022•44 citations
We experimentally study the behavior of a parametrically pumped nonlinear oscillator, which is based on a superconducting λ /4 resonator, and is terminated by a flux-tunable superconducting quantum interference device. We extract parameters for two devices. In particular, we study the effect of the nonlinearities in the system and compare to theory. The Duffing nonlinearity, α , is determined from the probe-power dependent frequency shift of the oscillator, and the nonlinearity, β , related to the parametric flux pumping, is determined from the pump amplitude for the onset of parametric oscillations. Both nonlinearities depend on the parameters of the device and can be tuned in situ by the applied dc flux. We also suggest how to cancel the effect of β by adding a small dc flux and a pump tone at twice the pump frequency.
In this licentiate thesis, I present the design, fabrication, and characterization of superconducting parametric resonators, for use in quantum information processing. These devices are quarter-wavelength coplanar waveguide resonators (~5 GHz), terminated at one end by a non-linear inductance provided by a SQUID (superconducting quantum interference device). The SQUID acts as a flux-controlled boundary condition, which effectively changes the electrical length of the resonator. This enables the modulation of the resonant frequency by coupling microwave magnetic flux into the SQUID, using on-chip transmission lines. The modulation occurs on a timescale much faster than the photon loss out of the resonator. The non-linearity provides several different regimes for operating this device. I focused on the parametric regime, in which the non-linear element was being modulated (pumped) at or near twice the resonant frequency. This pumping can lead to amplification and frequency conversion of an incoming signal. It can also give rise to instabilities and self-oscillations "parametric oscillations" - that is, the generation of an intense electric field in the resonator (the creation of photons). Parametric oscillations set in when the pumping strength exceeds a threshold value, and also depends on the pump-frequency detuning from twice the resonance and on the static flux through the SQUID. I characterized the devices over a wide parameter range by doing homodyne detection of the reflected signal or of the emitted field oscillations. In particular, I investigated the damping and two leading nonlinearities, dominating in different operating regimes, which influence the dynamics of the parametric resonator. First, I extracted the Duffing nonlinearity by studying the line width of the resonator as a function of the input signal (without pumping the SQUID). Second, with high pump amplitude, I extracted the pump-induced nonlinearity by determining the threshold parameters (pump amplitude and detuning) for the onset of parametric oscillations; this nonlinearity leads to the generation of higher-order pump terms that complicate the system dynamics, but can be mitigated now that they have been understood. My results validate a recent theoretical model for the classical, non-linear dynamics of parametric resonance, and helps determine workable design parameters. Finally, I helped develop a linearized model −-− the "pumpistor" - describing this device in terms of a flux-controlled impedance. This will be useful when designing more complex circuits. One goal of this work is to demonstrate single-shot measurements on superconducting qubits (quantum bits of information). We will use the parametric resonator as a threshold discriminator, associating the qubit's two energy eigenstates with the parametric oscillations either turning on or not. This would be a very useful device in the quantum engineer's toolbox when designing systems for quantum information processing and communication.
We investigate nondegenerate parametric oscillations in a superconducting microwave multimode resonator that is terminated by a superconducting quantum interference device (SQUID). The parametric effect is achieved by modulating magnetic flux through the SQUID at a frequency close to the sum of two resonator-mode frequencies. For modulation amplitudes exceeding an instability threshold, self-sustained oscillations are observed in both modes. The amplitudes of these oscillations show good quantitative agreement with a theoretical model. The oscillation phases are found to be correlated and exhibit strong fluctuations which broaden the oscillation spectral linewidths. These linewidths are significantly reduced by applying a weak on-resonant tone, which also suppresses the phase fluctuations. When the weak tone is detuned, we observe synchronization of the oscillation frequency with the frequency of the input. For the detuned input, we also observe an emergence of three idlers in the output. This observation is in agreement with theory indicating four-mode amplification and squeezing of a coherent input.
We have fabricated and studied a system of two tunable and coupled nonlinear superconducting resonators. The nonlinearity is introduced by galvanically coupled dc superconducting quantum interference devices. We simulate the system response by means of a circuit model, which includes an additional signal path introduced by the electromagnetic environment. Furthermore, we present two methods allowing us to experimentally determine the nonlinearity. First, we fit the measured frequency and flux dependence of the transmission data to simulations based on the equivalent circuit model. Second, we fit the power dependence of the transmission data to a model that is predicted by the nonlinear equation of motion describing the system. Our results show that we are able to tune the nonlinearity of the resonators by almost two orders of magnitude via an external coil and two on-chip antennas. The studied system represents a basic building block for larger systems, allowing for quantum simulations of bosonic many-body systems with a larger number of lattice sites.
We have developed a Josephson parametric amplifier comprising a superconducting coplanar-waveguide resonator terminated by a dc superconducting quantum interference device (SQUID). An external field (the pump, ∼20 GHz) modulates the flux threading of the dc SQUID and, therefore, the resonant frequency of the cavity field (the signal, ∼10 GHz), which leads to the parametric signal amplification. We operated the amplifier at different band centers and observed amplification (17 dB at maximum) and deamplification depending on the relative phase between the pump and the signal. The noise temperature is estimated to be less than 0.87 K.
In this Master thesis, I present a theoretical description and experimental measurements of a tunable microwave resonator operated as a parametric amplifier. Superconducting parametric amplifiers have attracted great interest in recent years as it has been demonstrated that they can operate with a noise performance at the standard quantum limit. \nParametric amplification is achieved in the devices by modulating the electrical length of the resonator at twice the resonance frequency. The device measured in this thesis consists of a quarter-wavelength microwave resonator fabricated in a thin-film aluminum coplanar waveguide geometry. With a termination to ground through a Superconducting Quantum Interference Device (SQUID), the boundary condition of the resonator becomes sensitive to an applied magnetic field. This enables the tuning of the resonance frequencies, using a DC magnetic field, over a wide frequency range of 670MHz. Similarly, an AC magnetic field then allows for the modulation of the resonator electrical length at microwave frequencies. \nWe characterized the device by first measuring the DC tuning curves of the 2nd and 3rd harmonics of the resonator, around 4 GHz and 6 GHz respectively. We then studied parametric amplification in the device when the electrical length was modulated at approximately twice the resonance frequency of one of the modes. We scanned the pump frequency and pump power over a wide range to study the region in parameters which gives parametric gain. We performed an in-depth parameter sweep over this region, identifying pump parameters that provided maximum gain and maximum system noise improvements compared the following HEMT amplifier. \nWe find that the use of the parametric amplifier can improve the system noise temperature by more than 10 dB compared to a start-of-the-art commercial HEMT amplifier. This implies a performance near the standard quantum limit.
We study microwave response of a Josephson parametric oscillator consisting of a superconducting transmission-line resonator with an embedded DC-superconducting quantum interference device (-SQUID). The DC-SQUID allows to control the magnitude of a Kerr nonlinearity over the ranges where it is smaller or larger than the photon loss rate. Spectroscopy measurements reveal the change in the microwave response from a classical Duffing oscillator to a Kerr parametric oscillator in a single device. In the single-photon Kerr regime, we observe parametric oscillations with a well-defined phase of either 0 or $\ensuremath{\pi}$, whose probability can be controlled by an externally injected signal.