Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:0812.4237 · Superconductor Science and Technology

Improving high-TCdc SQUID performance by means of junction asymmetry

Urbasi Sinha, Aninda Sinha, Frank K. Wilhelm

Published Mar 30, 2009• 3 citations
arXivHTMLPDF

Abstract

We study noise and noise energy of a high-T$_c$ dc SQUID fabricated on a high-$ε_R$ substrate whose conduction properties are given by transmission line physics. We show that transmission line resonances greatly enhance the noise. Remarkably, resistance asymmetry enhances these resonances even more. However, as the transfer function scales the same way, the noise energy is reduced by asymmetry greatly enhancing the flexibility and performance of the SQUID.

DOI
10.1088/0953-2048/22/5/055002

Related papers

On transmission line resonances in highTCdc SQUIDs

U Sinha, A Sinha, E J Tarte

In this paper, we study transmission line resonances in high T C dc SQUIDs (superconducting quantum interference devices). These resonances are exhibited in the characteristics of SQUIDs which are fabricated on substrates with high dielectric constant, such as strontium titanate. The power balance equation is analytically derived both for symmetric and for asymmetric SQUIDs. Using this, we investigate SQUID current–voltage I ( V ), voltage–flux V (Φ) and voltage modulation Δ V characteristics.

arXiv:0806.3187•Superconductor Science and Technology•Jun 18, 2008•3 citations

Performance of dc SQUIDs with resistively shunted inductance

Vittorio Foglietti, W. J. Gallagher, M. B. Ketchen +3 more

We have fabricated and characterized the noise performance of well-coupled Nb-Pb alloy edge junction dc superconducting quantum interference devices (SQUIDs) with a resistively shunted inductance. The extra damping resistor removes the resonances in the current-voltage characteristics resulting in a very low value of the extrinsic energy sensitivity in flux-locked-loop operation. Numerical simulations, with the junction capacitance included, indicate that the damping resistance does not degrade noise performance until it is significantly less than the junction-shunting resistance. We also tested different SQUID designs and demonstrated that a large SQUID inductance, proposed earlier to be desirable when resistively shunted, can seriously affect the low-frequency flux noise.

Applied Physics Letters•Oct 2, 1989•45 citations

Well coupled, low noise, dc SQUIDs

B. Muhlfelder, James A. Beall, Michael W. Cromar +2 more

We have designed, fabricated, and tested a Double Transformer (DT) coupled dc SQUID (Superconducting Quantum Interference Device) with low noise, an input inductance of 1μH and a smooth input-output characteristic. A transmission line model is presented to explain a resonance in the input-output characteristic of early versions of this device. Guided by the results of numerical simulations a new version of this device has been built and tested. Experimental results are presented that show that the resonance can be moved to a higher voltage by reducing the area of the SQUID loop. The voltage-external flux characteristic of some of these new devices agrees to within 10% with computer simulations. The minimum detectable energy per unit bandwidth (MDE) referred to the SQUID loop, is 10h, where h is Planck's constant. Computer simulations indicate an MDE of 6h.

IEEE Transactions on Magnetics•Mar 1, 1985•21 citations

Signal and white noise properties of edge junction dc SQUID’s

Ronald T. Wakai, Dale J. Van Harlingen

We have fabricated and characterized the noise performance of submicron edge junction dc superconducting quantum interference devices (SQUID’s) which exhibit excellent signal properties and extremely high flux sensitivity. At frequencies above about 3 MHz, the SQUID noise is white and is in reasonable agreement with computer simulations for a thermal noise-limited detector. In one device the measured flux energy resolution is 1.6±0.5ℏ at 1.5 K, within a factor of 2 of the quantum-limited value suggested by theoretical modeling.

Applied Physics Letters•Apr 4, 1988•21 citations

Noise characteristics of a dc SQUID with a resistively shunted inductance. II. Optimum damping

Keiji Enpuku, Keiji Yoshida, Satoshi Kohjiro

Effects of a damping resistance on noise characteristics of a dc SQUID are studied theoretically, where the damping resistance is in shunt with a loop inductance of the SQUID. An analytical expression for the energy resolution of the SQUID is obtained, with which the relation between the damping resistance and the energy resolution is studied in detail. It is shown that an optimum value of the damping resistance exists, which is determined by the tradeoff between the improvement of the transfer function and the additional noise due to the damping resistance. Optimum values of the damping resistance are about twice the shunt resistance of the SQUID and vary slightly with SQUID modulation parameter β. For optimum damping, the energy resolution is improved, compared with the case without the damping resistance. This means that the SQUID with large β can be used without significant degradation of the performance, i.e., the previous restriction of β=1 can be loosened. The analytical results agree quantitatively with numerical ones.

Journal of Applied Physics•Dec 15, 1986•66 citations

Excess low-frequency flux noise in dc SQUIDs

M. E. Huber, Michael W. Cromar, Ronald H. Ono

We have fabricated dc superconducting quantum interference devices (SQUIDs) incorporating Nb/Al-oxide/Nb Josephson junctions in both stripline and washer geometries. Low-frequency noise in excess of that predicted by the resistively-shunted junction model is present in both geometries and is demonstrated to be flux noise. This flux noise is not environmental. Improvements in fabrication processing over the past four years have reduced the level of this flux noise. SQUIDs are now fabricated with PdAu resistors, Nb wiring layers, and SiO/sub 2/ interlayer dielectric. In our best well-coupled SQUIDs, the white-noise energy sensitivity is 5/spl times/10/sup -31/ J/spl middot/s, with a 1/f knee below 0.1 Hz. We believe further reduction in the flux noise might be obtained with the use of on-chip flux shielding and/or trapping structures.

IEEE Transactions on Applied Superconductivity•Jun 1, 1997•6 citations
We study noise and noise energy of a high-Tc_cc​ dc SQUID fabricated on a high-εRε_RεR​ substrate whose conduction properties are given by transmission line physics. We show that transmission line resonances greatly enhance the noise. Remarkably, resistance asymmetry enhances these resonances even more. However, as the transfer function scales the same way, the noise energy is reduced by asymmetry greatly enhancing the flexibility and performance of the SQUID.
In this paper, we study transmission line resonances in high T C dc SQUIDs (superconducting quantum interference devices). These resonances are exhibited in the characteristics of SQUIDs which are fabricated on substrates with high dielectric constant, such as strontium titanate. The power balance equation is analytically derived both for symmetric and for asymmetric SQUIDs. Using this, we investigate SQUID current–voltage I ( V ), voltage–flux V (Φ) and voltage modulation Δ V characteristics.
We have fabricated and characterized the noise performance of well-coupled Nb-Pb alloy edge junction dc superconducting quantum interference devices (SQUIDs) with a resistively shunted inductance. The extra damping resistor removes the resonances in the current-voltage characteristics resulting in a very low value of the extrinsic energy sensitivity in flux-locked-loop operation. Numerical simulations, with the junction capacitance included, indicate that the damping resistance does not degrade noise performance until it is significantly less than the junction-shunting resistance. We also tested different SQUID designs and demonstrated that a large SQUID inductance, proposed earlier to be desirable when resistively shunted, can seriously affect the low-frequency flux noise.
We have designed, fabricated, and tested a Double Transformer (DT) coupled dc SQUID (Superconducting Quantum Interference Device) with low noise, an input inductance of 1μH and a smooth input-output characteristic. A transmission line model is presented to explain a resonance in the input-output characteristic of early versions of this device. Guided by the results of numerical simulations a new version of this device has been built and tested. Experimental results are presented that show that the resonance can be moved to a higher voltage by reducing the area of the SQUID loop. The voltage-external flux characteristic of some of these new devices agrees to within 10% with computer simulations. The minimum detectable energy per unit bandwidth (MDE) referred to the SQUID loop, is 10h, where h is Planck's constant. Computer simulations indicate an MDE of 6h.
We have fabricated and characterized the noise performance of submicron edge junction dc superconducting quantum interference devices (SQUID’s) which exhibit excellent signal properties and extremely high flux sensitivity. At frequencies above about 3 MHz, the SQUID noise is white and is in reasonable agreement with computer simulations for a thermal noise-limited detector. In one device the measured flux energy resolution is 1.6±0.5ℏ at 1.5 K, within a factor of 2 of the quantum-limited value suggested by theoretical modeling.
Effects of a damping resistance on noise characteristics of a dc SQUID are studied theoretically, where the damping resistance is in shunt with a loop inductance of the SQUID. An analytical expression for the energy resolution of the SQUID is obtained, with which the relation between the damping resistance and the energy resolution is studied in detail. It is shown that an optimum value of the damping resistance exists, which is determined by the tradeoff between the improvement of the transfer function and the additional noise due to the damping resistance. Optimum values of the damping resistance are about twice the shunt resistance of the SQUID and vary slightly with SQUID modulation parameter β. For optimum damping, the energy resolution is improved, compared with the case without the damping resistance. This means that the SQUID with large β can be used without significant degradation of the performance, i.e., the previous restriction of β=1 can be loosened. The analytical results agree quantitatively with numerical ones.
We have fabricated dc superconducting quantum interference devices (SQUIDs) incorporating Nb/Al-oxide/Nb Josephson junctions in both stripline and washer geometries. Low-frequency noise in excess of that predicted by the resistively-shunted junction model is present in both geometries and is demonstrated to be flux noise. This flux noise is not environmental. Improvements in fabrication processing over the past four years have reduced the level of this flux noise. SQUIDs are now fabricated with PdAu resistors, Nb wiring layers, and SiO/sub 2/ interlayer dielectric. In our best well-coupled SQUIDs, the white-noise energy sensitivity is 5/spl times/10/sup -31/ J/spl middot/s, with a 1/f knee below 0.1 Hz. We believe further reduction in the flux noise might be obtained with the use of on-chip flux shielding and/or trapping structures.