Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:0801.3761 · Low Temperature Physics

Magnetic flux noise in the three-Josephson-junction superconducting ring

Evgeni V. Il’ichev, A. N. Omelyanchouk

Published Jun 1, 2008• 2 citations
arXivHTMLPDF

Abstract

We analyze the influence of noise on magnetic properties of a superconducting loop which contains three Josephson junctions. This circuit is a classical analog of a persistent current (flux) qubit. A loop supercurrent induced by external magnetic field in the presence of thermal fluctuations is calculated. To connect with experiment, we calculate the impedance of a low-frequency tank circuit which is inductively coupled with the loop of interest. We compare the results with the results obtained in the quantum mode — when the three junction loop exhibits quantum tunneling of the magnetic flux. We demonstrate that the tank–loop impedance in the classical and quantum modes have different temperature dependence and can be easily distinguished experimentally.

DOI
10.1063/1.2920076

Related papers

Magnetic flux noise in SQUIDs and qubits

Steven M. Anton

For over three decades, the presence of magnetic flux noise with a power spectral density scaling roughly as $S_Phi(f) propto 1/f^alpha$, where $alpha lesssim 1$, has been known to limit the low-frequency performance of dc superconducting quantum interference devices (SQUIDs). In recent years, experiments indicate that this same noise persists to frequencies up to 1~GHz and is a dominant source of dephasing in flux-sensitive superconducting quantum bits (qubits). Thus, the reduction of flux noise presents a major hurdle towards the successful realization of scalable quantum computers that are based on flux-based qubits. In this thesis, we present experimental measurements, theoretical analyses, and numerical simulations that support a more detailed understanding of both the microscopic and macroscopic properties of flux noise.Our experimental work begins with flux noise measurements of a large number of SQUIDs in the temperature range from 0.1~K to 4~K. We report on measurements of ten SQUIDs with systematically varied geometries and show that $alpha$ increases as the temperature is lowered; in so doing, each spectrum pivots about a nearly constant frequency. The mean square flux noise, inferred by integrating the power spectra, grows rapidly with temperature and at a given temperature is approximately independent of the outer dimension of a given SQUID washer. We show that these results are incompatible with a model based on the random reversal of independent, spins that are located at the surface of the SQUID washer.In the course of our flux noise measurements, we became aware of a spurious contribution to low-frequency critical current noise in Josephson junctions---normally attributed to charge trapping in the barrier---arising from temperature instabilities inherent in cryogenic systems. These temperature fluctuations modify the critical current via its temperature dependence. By computing cross-correlations between measured temperature and critical current noise in Al-AlOx-Al junctions, we show that, despite excellent temperature stability, temperature fluctuations induce observable critical current fluctuations. Particularly, because $1/f$ critical current noise has decreased with improved fabrication techniques in recent years, it is important to understand and eliminate this additional noise source.Next, we introduce a numerical method of calculating the mean square flux noise $Phisq$ from independently fluctuating spins on the surface of thin-film loops of arbitrary geometry. By reciprocity, $Phisq$ is proportional to $langleBbf(rbf)^2rangle$, where $Bbf(rbf)$ is the magnetic field generated by a circulating current around the loop and $rbf$ varies over the loop surface. By discretizing the loop nonuniformly, we efficiently and accurately compute the current distribution and resulting magnetic field, which may vary rapidly across the loop. We use this method to compute $Phisq$ in a number of scenarios in which we systematically vary physical parameters of the loop. We compare our simulations to an earlier analytic result predicting that $Phisq propto R/W$ in the limit where the loop radius $R$ is much greater than the linewidth $W$. We further show that the previously neglected contribution of edge spins to $Phisq$ is significant---even dominant---in narrow-linewidth loops.To calculate theoretical dephasing rates in qubits, we consider flux noise with a spectral density $S_Phi(f) = A^2/(f/1~hbox{Hz})^alpha$, where $A$ is of the order of 1~$muPhi_0 , hbox{Hz}^{-1/2}$ and $0.6 leq alpha leq 1.2$; $Phi_{0}$ is the flux quantum. For a qubit with an energy level splitting linearly coupled to the applied flux, our calculations of the dependence of the pure dephasing time $tau_phi$ of Ramsey and echo pulse sequences on $alpha$ for fixed $A$ show that $tau_phi$ decreases rapidly as $alpha$ is reduced. We find that $tau_phi$ is relatively insensitive to the noise bandwidth, $f_1 leq f leq f_2$, for all $alpha$ provided the ultraviolet cutoff frequency $f_2 > 1/tau_phi$. We calculate the ratio $tau_{phi,E} / tau_{phi,R}$ of the echo ($E$) and Ramsey ($R$) sequences, and the dependence of the decay function on $alpha$ and $f_2$. We investigate the case in which $S_Phi(f_0)$ is fixed at the ``pivot frequency'' $f_0 neq 1$~Hz while $alpha$ is varied, and find that the choice of $f_0$ can greatly influence the sensitivity of $tau_{phi,E}$ and $tau_{phi,R}$ to the value of $alpha$.Finally, we conclude with a brief review of our principal results and conclusions. We also comment on promising avenues of future research.

•Jan 1, 2013•0 citations

Coupling Effect in Dual Three-Josephson-Junction Loops in Classical Regime

Yoshihiro Shimazu

We investigate the behavior of dual three-Josephson-junction loops coupled through a mutual inductance in the classical regime. The energy levels and the circulating currents in the loops are calculated as a function of applied external magnetic flux. The calculation shows that the coupling effect leads to the sequential reversal of the circulating currents in the loops. We measured the magnetic flux due to the circulating currents with a DC-SQUID in a flux-locked loop configuration. We demonstrate that the states of the coupled system can be manipulated with a magnetic field. The observed magnetic flux agrees very well with the simulation results based on the measurement of an inductance associated with a superconducting wire. The observed reversal of the circulating currents is explained in terms of the noise-activated escape from the metastable state in a six-dimensional potential.

Journal of the Physical Society of Japan•Jul 15, 2004•2 citations

Characterization of superconducting structures designed for qubit realizations

Evgeni V. Il’ichev, Th. Wagner, Ludwig Fritzsch +10 more

We implement the impedance measurement technique in order to characterize superconducting structures designed for applications in quantum computing. We report an experimental study of the circuit consisting of three small Josephson junctions incorporated in a low-inductance superconducting loop. Measurements of the circuit response to an applied weak ac bias as a function of the external magnetic flux φe yield complete information on the properties of the circuit. We found that the system displays two metastable states. From experimental data, we have determined the magnetic field dependent Josephson energy U(φe) of these states, the potential barrier ΔU between these states, as well as the difference of the critical currents of the junction in the loop.

Applied Physics Letters•Jun 3, 2002•34 citations

Low-frequency characterization of quantum tunneling in flux qubits

Ya. S. Greenberg, A. Izmalkov, M. Grajcar +5 more

We propose to investigate flux qubits by the impedance measurement technique (IMT), currently used to determine the current-phase relation in Josephson junctions. We analyze in detail the case of a high-quality tank circuit coupled to a persistent-current qubit, to which the IMT was successfully applied in the classical regime. It is shown that the low-frequency IMT can give considerable information about the level anticrossing, in particular the value of the tunneling amplitude. An interesting difference exists between applying the ac bias directly to the tank and indirectly via the qubit. In the latter case, a convenient way to find the degeneracy point in situ is described. Our design only involves existing technology, and its noise tolerance is quantitatively estimated to be realistic.

arXiv:cond-mat/0208076•Physical review. B, Condensed matter•Dec 31, 2002•63 citations

Josephson Persistent Current Qubit and Quantum Flux Measurements

Caspar H. van der Wal, Johan E. Mooij, A. C. Wallast +10 more

. In circuits of underdamped, small-capacitance Josephson junctions, the charge and phase variables behave quantum mechanically. Superpositions of charge states and flux states have been demonstrated, as well as microwave induced quantum dynamics (see e.g. refs [3, 4]). These e#ects have their origin in the conjugation of the phase and charge variables of Josephson circuits. The qubit design that we present here also contains small-capacitance Josephson junctions. However, even though charge-phase conjugation underlies the quantum behavior of the qubit, it was explicitly designed to be very insensitive to charge e#ects. In practice, random background charges and 1/f charge noise are always present in Josephson circuits, but these charge e#ects have negligible influence on the qubit. The qubit loop contains three Josephson junctions. Two junctions have Josephson coupling E J , the third junction has a coupling of #E J .Weaim

•Nov 21, 2007•0 citations

Measurements of 1∕f noise in Josephson junctions at zero voltage: Implications for decoherence in superconducting quantum bits

Michael Mück, Matthias Korn, Chas Mugford +2 more

Critical current fluctuations with a 1∕f spectral density (f is frequency) are potentially a limiting source of intrinsic decoherence in superconducting quantum bits (qubits) based on Josephson tunnel junctions. Prior measurements of this noise were made at nonzero voltages whereas qubits are operated in the zero voltage state. We report measurements of 1∕f noise in a dc superconducting quantum interference device first, coupled to a resonant tank circuit and operated in a dispersive mode at zero voltage, and, second, operated conventionally with a current bias in the voltage regime. Both measurements yield essentially the same magnitude of critical current 1∕f noise.

arXiv:cond-mat/0501153•Applied Physics Letters•Dec 27, 2004•19 citations
We analyze the influence of noise on magnetic properties of a superconducting loop which contains three Josephson junctions. This circuit is a classical analog of a persistent current (flux) qubit. A loop supercurrent induced by external magnetic field in the presence of thermal fluctuations is calculated. To connect with experiment, we calculate the impedance of a low-frequency tank circuit which is inductively coupled with the loop of interest. We compare the results with the results obtained in the quantum mode — when the three junction loop exhibits quantum tunneling of the magnetic flux. We demonstrate that the tank–loop impedance in the classical and quantum modes have different temperature dependence and can be easily distinguished experimentally.
For over three decades, the presence of magnetic flux noise with a power spectral density scaling roughly as SPhi(f)propto1/falphaS_Phi(f) propto 1/f^alphaSP​hi(f)propto1/falpha, where alphalesssim1alpha lesssim 1alphalesssim1, has been known to limit the low-frequency performance of dc superconducting quantum interference devices (SQUIDs). In recent years, experiments indicate that this same noise persists to frequencies up to 1~GHz and is a dominant source of dephasing in flux-sensitive superconducting quantum bits (qubits). Thus, the reduction of flux noise presents a major hurdle towards the successful realization of scalable quantum computers that are based on flux-based qubits. In this thesis, we present experimental measurements, theoretical analyses, and numerical simulations that support a more detailed understanding of both the microscopic and macroscopic properties of flux noise.Our experimental work begins with flux noise measurements of a large number of SQUIDs in the temperature range from 0.1~K to 4~K. We report on measurements of ten SQUIDs with systematically varied geometries and show that alphaalphaalpha increases as the temperature is lowered; in so doing, each spectrum pivots about a nearly constant frequency. The mean square flux noise, inferred by integrating the power spectra, grows rapidly with temperature and at a given temperature is approximately independent of the outer dimension of a given SQUID washer. We show that these results are incompatible with a model based on the random reversal of independent, spins that are located at the surface of the SQUID washer.In the course of our flux noise measurements, we became aware of a spurious contribution to low-frequency critical current noise in Josephson junctions---normally attributed to charge trapping in the barrier---arising from temperature instabilities inherent in cryogenic systems. These temperature fluctuations modify the critical current via its temperature dependence. By computing cross-correlations between measured temperature and critical current noise in Al-AlOx-Al junctions, we show that, despite excellent temperature stability, temperature fluctuations induce observable critical current fluctuations. Particularly, because 1/f1/f1/f critical current noise has decreased with improved fabrication techniques in recent years, it is important to understand and eliminate this additional noise source.Next, we introduce a numerical method of calculating the mean square flux noise PhisqPhisqPhisq from independently fluctuating spins on the surface of thin-film loops of arbitrary geometry. By reciprocity, PhisqPhisqPhisq is proportional to langleBbf(rbf)2ranglelangleBbf(rbf)^2ranglelangleBbf(rbf)2rangle, where Bbf(rbf)Bbf(rbf)Bbf(rbf) is the magnetic field generated by a circulating current around the loop and rbfrbfrbf varies over the loop surface. By discretizing the loop nonuniformly, we efficiently and accurately compute the current distribution and resulting magnetic field, which may vary rapidly across the loop. We use this method to compute PhisqPhisqPhisq in a number of scenarios in which we systematically vary physical parameters of the loop. We compare our simulations to an earlier analytic result predicting that PhisqproptoR/WPhisq propto R/WPhisqproptoR/W in the limit where the loop radius RRR is much greater than the linewidth WWW. We further show that the previously neglected contribution of edge spins to PhisqPhisqPhisq is significant---even dominant---in narrow-linewidth loops.To calculate theoretical dephasing rates in qubits, we consider flux noise with a spectral density SPhi(f)=A2/(f/1 hboxHz)alphaS_Phi(f) = A^2/(f/1~hbox{Hz})^alphaSP​hi(f)=A2/(f/1 hboxHz)alpha, where AAA is of the order of 1~muPhi0,hboxHz−1/2muPhi_0 , hbox{Hz}^{-1/2}muPhi0​,hboxHz−1/2 and 0.6leqalphaleq1.20.6 leq alpha leq 1.20.6leqalphaleq1.2; Phi0Phi_{0}Phi0​ is the flux quantum. For a qubit with an energy level splitting linearly coupled to the applied flux, our calculations of the dependence of the pure dephasing time tauphitau_phitaup​hi of Ramsey and echo pulse sequences on alphaalphaalpha for fixed AAA show that tauphitau_phitaup​hi decreases rapidly as alphaalphaalpha is reduced. We find that tauphitau_phitaup​hi is relatively insensitive to the noise bandwidth, f1leqfleqf2f_1 leq f leq f_2f1​leqfleqf2​, for all alphaalphaalpha provided the ultraviolet cutoff frequency f2>1/tauphif_2 > 1/tau_phif2​>1/taup​hi. We calculate the ratio tauphi,E/tauphi,Rtau_{phi,E} / tau_{phi,R}tauphi,E​/tauphi,R​ of the echo (EEE) and Ramsey (RRR) sequences, and the dependence of the decay function on alphaalphaalpha and f2f_2f2​. We investigate the case in which SPhi(f0)S_Phi(f_0)SP​hi(f0​) is fixed at the ``pivot frequency'' f0neq1f_0 neq 1f0​neq1~Hz while alphaalphaalpha is varied, and find that the choice of f0f_0f0​ can greatly influence the sensitivity of tauphi,Etau_{phi,E}tauphi,E​ and tauphi,Rtau_{phi,R}tauphi,R​ to the value of alphaalphaalpha.Finally, we conclude with a brief review of our principal results and conclusions. We also comment on promising avenues of future research.
We investigate the behavior of dual three-Josephson-junction loops coupled through a mutual inductance in the classical regime. The energy levels and the circulating currents in the loops are calculated as a function of applied external magnetic flux. The calculation shows that the coupling effect leads to the sequential reversal of the circulating currents in the loops. We measured the magnetic flux due to the circulating currents with a DC-SQUID in a flux-locked loop configuration. We demonstrate that the states of the coupled system can be manipulated with a magnetic field. The observed magnetic flux agrees very well with the simulation results based on the measurement of an inductance associated with a superconducting wire. The observed reversal of the circulating currents is explained in terms of the noise-activated escape from the metastable state in a six-dimensional potential.
We implement the impedance measurement technique in order to characterize superconducting structures designed for applications in quantum computing. We report an experimental study of the circuit consisting of three small Josephson junctions incorporated in a low-inductance superconducting loop. Measurements of the circuit response to an applied weak ac bias as a function of the external magnetic flux φe yield complete information on the properties of the circuit. We found that the system displays two metastable states. From experimental data, we have determined the magnetic field dependent Josephson energy U(φe) of these states, the potential barrier ΔU between these states, as well as the difference of the critical currents of the junction in the loop.
We propose to investigate flux qubits by the impedance measurement technique (IMT), currently used to determine the current-phase relation in Josephson junctions. We analyze in detail the case of a high-quality tank circuit coupled to a persistent-current qubit, to which the IMT was successfully applied in the classical regime. It is shown that the low-frequency IMT can give considerable information about the level anticrossing, in particular the value of the tunneling amplitude. An interesting difference exists between applying the ac bias directly to the tank and indirectly via the qubit. In the latter case, a convenient way to find the degeneracy point in situ is described. Our design only involves existing technology, and its noise tolerance is quantitatively estimated to be realistic.
. In circuits of underdamped, small-capacitance Josephson junctions, the charge and phase variables behave quantum mechanically. Superpositions of charge states and flux states have been demonstrated, as well as microwave induced quantum dynamics (see e.g. refs [3, 4]). These e#ects have their origin in the conjugation of the phase and charge variables of Josephson circuits. The qubit design that we present here also contains small-capacitance Josephson junctions. However, even though charge-phase conjugation underlies the quantum behavior of the qubit, it was explicitly designed to be very insensitive to charge e#ects. In practice, random background charges and 1/f charge noise are always present in Josephson circuits, but these charge e#ects have negligible influence on the qubit. The qubit loop contains three Josephson junctions. Two junctions have Josephson coupling E J , the third junction has a coupling of #E J .Weaim
Critical current fluctuations with a 1∕f spectral density (f is frequency) are potentially a limiting source of intrinsic decoherence in superconducting quantum bits (qubits) based on Josephson tunnel junctions. Prior measurements of this noise were made at nonzero voltages whereas qubits are operated in the zero voltage state. We report measurements of 1∕f noise in a dc superconducting quantum interference device first, coupled to a resonant tank circuit and operated in a dispersive mode at zero voltage, and, second, operated conventionally with a current bias in the voltage regime. Both measurements yield essentially the same magnitude of critical current 1∕f noise.